scholarly journals Analytical Solutions to Conservative and Non-Conservative Water Quality Constituents in Water Distribution System Storage Tanks

Water ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 3502
Author(s):  
Biniam Abrha ◽  
Avi Ostfeld
Keyword(s):  
Water Quality ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Compartment Model ◽  
Storage Tanks ◽  
Water Quality Simulation ◽  
Negative Impacts ◽  
Critical Components

Water storage tanks are one of the primary and most critical components of water distribution systems (WDSs), which aim to manage water supply by maintaining pressure. In addition, storage provides a surplus source of water in case of an emergency. To gain the mentioned advantages, storage tanks are incorporated in most WDSs. Despite these advantages, storage can also pose negative impacts on water quality, thereby affecting water utilities. Water quality problems are a result of longer residency times and inadequate water mixing. This study aimed to construct a model of a tank’s water quantity and quality by formulating and solving governing equations based on inlet/outlet configurations and processes that influence the movement of water and chemical substances inside it. We used a compartment model to characterize the mixing behavior inside a tank. A water quality simulation model with different compartment arrangements was explored for extended filling and draining of storage, which was further validated using a previously published case study.

scholarly journals Water quality event detection and customer complaint clustering analysis in distribution systems

2012 ◽  
Vol 12 (5) ◽  
pp. 580-587 ◽  
Author(s):  
Stephen Mounce ◽  
John Machell ◽  
Joby Boxall
Keyword(s):  
Water Quality ◽  
Drinking Water ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Source ◽  
Water Quality Monitoring ◽  
Water Utility ◽  
Drinking Water Distribution ◽  
Historic Data

Safe, clean drinking water is a foundation of society and water quality monitoring can contribute to ensuring this. A case study application of the CANARY software to historic data from a UK drinking water distribution system is described. Sensitivity studies explored appropriate choice of algorithmic parameter settings for a baseline site, performance was evaluated with artificial events and the system then transferred to all sites. Results are presented for analysis of nine water quality sensors measuring six parameters and deployed in three connected district meter areas (DMAs), fed from a single water source (service reservoir), for a 1 year period and evaluated using comprehensive water utility records with 86% of event clusters successfully correlated to causes (spatially limited to DMA level). False negatives, defined by temporal clusters of water quality complaints in the pilot area not corresponding to detections, were only approximately 25%. It was demonstrated that the software could be configured and applied retrospectively (with potential for future near real time application) to detect various water quality event types (with a wider remit than contamination alone) for further interpretation.

scholarly journals Management of water distribution systems in PDA conditions using isolation valves: case studies of real networks

2019 ◽  
Vol 22 (4) ◽  
pp. 681-690 ◽  
Author(s):  
A. Fiorini Morosini ◽  
O. Caruso ◽  
P. Veltri
Keyword(s):  
Case Studies ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Distribution System ◽  
Water Distribution Network ◽  
Optimal Number ◽  
System Management ◽  
System Control

Abstract The current paper reports on a case study investigating water distribution system management in emergency conditions when it is necessary to seal off a zone with isolation valves to allow repair. In these conditions, the pressure-driven analysis (PDA) is considered to be the most efficient approach for the analysis of a water distribution network (WDN), as it takes into account whether the head in a node is adequate to ensure service. The topics of this paper are innovative because, until now, previous approaches were based on the analysis of the network behaviour in normal conditions. In emergency conditions, it is possible to measure the reliable functioning of the system by defining an objective function (OF) that helps to choose the optimal number of additional valves in order to obtain adequate system control. The OF takes into account the new network topology by excluding the zone where the broken pipe is located. The results show that the solution did not improve significantly when the number of valves reached a threshold. The procedure applied to other real case studies seems to confirm the efficiency of the methodology even if further examination of other cases in different conditions is necessary.

Determination of cast iron pipe wall decay coefficient for combined chlorine in a municipal water distribution system

2015 ◽  
Vol 42 (4) ◽  
pp. 250-258 ◽  
Author(s):  
Megan J. Liu ◽  
Stephen Craik ◽  
David Z. Zhu
Keyword(s):  
Water Quality ◽  
Cast Iron ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Distribution System ◽  
Water Quality Model ◽  
Quality Model ◽  
Decay Coefficient ◽  
Municipal Water

Predicting disinfectant concentrations in water distribution systems using water quality models requires the input of the wall decay coefficient of the disinfectant. In this study, field water sampling data was integrated with network hydraulic and water quality model simulations of a section of the municipal water distribution system in the City of Edmonton, composed of predominantly cast iron piping, to determine a wall decay coefficient for combined chlorine (chloramine). Unique combined chlorine wall decay coefficients that provided the best fit of model-predicted chlorine concentrations to the field data were determined at two temperatures. Using the determined wall decay coefficients, the water quality model can be used to predict combined chlorine concentrations.

scholarly journals The Impacts of Spatially Variable Demand Patterns on Water Distribution System Design and Operation

Water ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 567 ◽  
Author(s):  
Kegong Diao ◽  
Robert Sitzenfrei ◽  
Wolfgang Rauch
Keyword(s):  
Water Quality ◽  
System Design ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Distribution System ◽  
Service Failure ◽  
Design Flow ◽  
Level Of Service ◽  
Demand Patterns

Resilient water distribution systems (WDSs) need to minimize the level of service failure in terms of magnitude and duration over its design life when subject to exceptional conditions. This requires WDS design to consider scenarios as close as possible to real conditions of the WDS to avoid any unexpected level of service failure in future operation (e.g., insufficient pressure, much higher operational cost, water quality issues, etc.). Thus, this research aims at exploring the impacts of design flow scenarios (i.e., spatial-variant demand patterns) on water distribution system design and operation. WDSs are traditionally designed by using a uniform demand pattern for the whole system. Nevertheless, in reality, the patterns are highly related to the number of consumers, service areas, and the duration of peak flows. Thus, water distribution systems are comprised of distribution blocks (communities) organized in a hierarchical structure. As each community may be significantly different from the others in scale and water use, the WDSs have spatially variable demand patterns. Hence, there might be considerable variability of real flow patterns for different parts of the system. Consequently, the system operation might not reach the expected performance determined during the design stage, since all corresponding facilities are commonly tailor-made to serve the design flow scenario instead of the real situation. To quantify the impacts, WDSs’ performances under both uniform and spatial distributed patterns are compared based on case studies. The corresponding impacts on system performances are then quantified based on three major metrics; i.e., capital cost, energy cost, and water quality. This study exemplifies that designing a WDS using spatial distributed demand patterns might result in decreased life-cycle cost (i.e., lower capital cost and nearly the same pump operating cost) and longer water ages. The outcomes of this study provide valuable information regarding design and operation of water supply infrastructures; e.g., assisting the optimal design.

Multi-stage response to contaminant ingress into water distribution systems and probability quantification

2009 ◽  
Vol 36 (11) ◽  
pp. 1764-1772 ◽  
Author(s):  
Hailiang Shen ◽  
Edward A. McBean ◽  
Mirnader Ghazali
Keyword(s):  
Data Mining ◽  
Distribution System ◽  
Euclidean Distance ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Distribution System ◽  
Location Information ◽  
Multi Stage ◽  
Actual Point

A multi-stage response procedure for identifying possible ingress nodes (PINs) and quantifying the likelihood that a PIN in a given water distribution system is the actual point of ingress is described. The procedure uses data mining to successively decrease the number of PINs based on a pre-constructed database. In each stage, query sentences are executed to locate the PINs and a Euclidean distance is proposed to estimate the probability, to allow the identification of locations with the highest probabilities of being the true ingress location. As demonstrated in a case study, the ranges of PINs are reduced in the 1st, 2nd, and 3rd stages; except the first sensor alarm, the Euclidean distance metric can identify the true ingress node with the program run-time of less than 2 min; the multi-stage procedure saves roughly 3 h in identifying the true ingress node after the second sensor alarm, instead of waiting for a third sensor alarm to provide the location information. The multi-stage response procedure is shown to be an effective and efficient way for identification and probability quantification of PINs.

scholarly journals Assessment of probable causes of chlorine decay in water distribution systems of Gaborone city, Botswana

Water SA ◽  
2019 ◽  
Vol 45 (2 April) ◽  
Author(s):  
Denis Nono ◽  
Phillimon T Odirile ◽  
Innocent Basupi ◽  
Bhagabat P Parida
Keyword(s):  
Water Quality ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Inorganic Compounds ◽  
Quality Parameters ◽  
Water Quality Parameters ◽  
Biofilm Growth ◽  
Reaction Rate Constants ◽  
Chlorine Decay

Assessment of probable causes of chlorine decay in water distribution systems of Gaborone city, Botswana Gaborone city water distribution system (GCWDS) is rapidly expanding and has been faced with the major problems of high water losses due to leakage, water shortages due to drought and inadequate chlorine residuals at remote areas of the network. This study investigated the probable causes of chlorine decay, due to pipe wall conditions and distribution system water quality in the GCWDS. An experimental approach, which applied a pipe-loop network model to estimate biofilm growth and chlorine reaction rate constants, was used to analyse pipe wall chlorine decay. Also, effects of key water quality parameters on chlorine decay were analysed. The water quality parameters considered were: natural organic matter (measured by total organic carbon, TOC; dissolved organic carbon, DOC; and ultraviolet absorbance at wavelength 254, UVA-254, as surrogates), inorganic compounds (iron and manganese) and heterotrophic plate count (HPC). Samples were collected from selected locations in the GCWDS for analysis of water quality parameters. The results of biofilm growth and chlorine reaction rate constants revealed that chlorine decay was higher in pipe walls than in the bulk of water in the GCWDS. The analysis of key water quality parameters revealed the presence of TOC, DOC and significant levels of organics (measured by UVA-254), which suggests that organic compounds contributed to chlorine decay in the GCWDS. However, low amounts of iron and manganese (< 0.3 mg/L) indicated that inorganic compounds may have had insignificant contributions to chlorine decay. The knowledge gained on chlorine decay would be useful for improving water treatment and network operating conditions so that appropriate chlorine residuals are maintained to protect the network from the risks of poor water quality that may occur due to the aforementioned problems.

scholarly journals Evaluation of corrosion and scaling tendency indices in a drinking water distribution system: a case study of Bandar Abbas city, Iran

2014 ◽  
Vol 13 (1) ◽  
pp. 203-209 ◽  
Author(s):  
Vali Alipour ◽  
Kavoos Dindarloo ◽  
Amir Hossein Mahvi ◽  
Leila Rezaei
Keyword(s):  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Distribution System ◽  
Total Hardness ◽  
Test Results ◽  
System A ◽  
Drinking Water Distribution ◽  
Bandar Abbas

Corrosion and scaling is a major problem in water distribution systems, thus evaluation of water corrosivity properties is a routine test in water networks. To evaluate water stability in the Bandar Abbas water distribution system, the network was divided into 15 clusters and 45 samples were taken. Langelier, Ryznar, Puckorius, Larson–Skold (LS) and Aggressive indices were determined and compared to the marble test. The mean parameters included were pH (7.8 ± 0.1), electrical conductivity (1,083.9 ± 108.7 μS/cm), total dissolved solids (595.7 ± 54.7 mg/L), Cl (203.5 ± 18.7 mg/L), SO4 (174.7 ± 16.0 mg/L), alkalinity (134.5 ± 9.7 mg/L), total hardness (156.5 ± 9.3 mg/L), HCO3 (137.4 ± 13.0 mg/L) and calcium hardness (71.8 ± 4.3 mg/L). According to the Ryznar, Puckorius and Aggressive Indices, all samples were stable; based on the Langelier Index, 73% of samples were slightly corrosive and the rest were scale forming; according to the LS index, all samples were corrosive. Marble test results showed tested water of all 15 clusters tended to scale formation. Water in Bandar Abbas is slightly scale forming. The most appropriate indices for the network conditions are the Aggressive, Puckorius and Ryznar indices that were consistent with the marble test.

scholarly journals Water Quality Correction Within Water Distribution System

2015 ◽  
Vol 22 (3) ◽  
pp. 401-410 ◽  
Author(s):  
Dariusz Kowalski ◽  
Beata Kowalska ◽  
Ewa Hołota ◽  
Artur Choma
Keyword(s):  
Water Quality ◽  
Water Loss ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Manufacturing Industry ◽  
Water Distribution Systems ◽  
Special Treatment ◽  
Management Processes ◽  
Secondary Contamination

Abstract Water suppliers can be treated as production companies whose main product is water delivered to their customers. The article presents problems connected with management of such companies in the conditions of secondary contamination in water distribution systems. This phenomenon exists in water networks all over the world. Its’ presence is particularly visible in countries of former communistic block. In the article particular attention was devoted to the issue of water quality correction in the analysed systems. In the case of water distribution systems, former quality correction methods consisted in special treatment of water pumped into the system, flushing and cleaning of water pipes. In both these cases identification of water quality deficiencies resulted in significant water loss. The situation reflects management processes applied in the manufacturing industry of the 1940s. The authors of this paper put forward the concept of three water quality correction methods which would not entail such considerable water loss. The methods in question are intended for different network types. The implementation of proposed solutions could set new standards in management of distribution systems of water providers.

Sign in / Sign up

Export Citation Format

Share Document