scholarly journals Erythrosine and Rhodamine Dyes as a Solar Cell Concentrator

2019 ◽  
Vol 54 (4) ◽  
Author(s):  
Suhad Hassan Mohsen ◽  
Luma Hafedh Abed Oneizah ◽  
Warood Kream Alaarage
Keyword(s):  
Solar Cell ◽  
Fill Factor ◽  
Organic Dyes ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Photovoltaic Cell ◽  
Open Circuit ◽  
Solar Cell Efficiency ◽  
Cell Efficiency ◽  
Rhodamine Dyes

In this work, a solar and flash center was created by combining two organic dyes, erythrosine and rhodamine, with completely different concentrations. Throughout the spectra of fluorescence (F) and absorbance (A), the quantitative efficiency of the dye mixture was determined. It was manufactured from a panel of epoxy containing a mixture of the two dyes using open-circuit voltage (Voc), short-circuit current (Isc), fill factor (FF), and solar cell efficiency (η). It was found that a 1 mm thickness of the panel works best in increasing the efficiency of the photovoltaic cell.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals Simulation Effect of Ga2O3 layer thickness on CdTe solar cell by SCAPS-1D

2019 ◽  
Vol 24 (6) ◽  
pp. 110
Author(s):  
Adnan Alwan Mouhammed ◽  
Ayed N. Saleh
Keyword(s):  
Optical Properties ◽  
Solar Cell ◽  
Oxide Layer ◽  
Gallium Oxide ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Open Circuit ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

The effect of Ga2O3 thickness on CdTe cells was studied using the SCAPS-1D simulator. The best solar cell efficiency (14.65%) was found at the thickness of the gallium oxide layer (1-10nm) and the cell efficiency (η) decrease with an increase in the thickness of the oxide layer and the decrease of the fill factor, thus decreasing the voltage current (I-V) and decreasing the current of the short circuit (Isc). The value of the open circuit voltage (VOC) is approximately constant and at 0.76V. The optical properties of the cell of quantitative efficiency are 86% and decrease within 18nm   http://dx.doi.org/10.25130/tjps.24.2019.116

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

2013 ◽  
Vol 665 ◽  
pp. 330-335 ◽  
Author(s):  
Ripal Parmar ◽  
Dipak Sahay ◽  
R.J. Pathak ◽  
R.K. Shah
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Energy ◽  
Open Circuit ◽  
Cell Parameters ◽  
Photoelectrochemical Solar Cell ◽  
Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

Design and Numerical Simulation on the Optical and Electrical Behavior of a ZnO:Al Nanowire Array a-Si pin Solar Cell

2008 ◽  
Vol 1101 ◽  
Author(s):  
Chang-Wei Liu ◽  
Zingway Pei ◽  
Shu-Tong Chang ◽  
Ren-Yui Ho ◽  
Min-Wei Ho ◽  
...  
Keyword(s):  
Solar Cell ◽  
Carrier Transport ◽  
Fill Factor ◽  
Cell Structure ◽  
Short Circuit ◽  
Nanowire Array ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Si Solar Cell ◽  
Sun Light

AbstractOne of the parameters that limit the efficiency of a thin film solar cell, especially the a-Si and the nc-Si solar cell is the cell thickness. Although thicker film can absorb most of the sun light, the optical generated carriers will recombination through the numerous gap states in the film that obtained lower short circuit current and fill factor. In the controversy, thinner film could not absorb enough sun light that also limit the short circuit current. In this works, we utilize nanowire structure to solve the conflict between the light absorption and the carrier transport. The designed structure has ZnO:Al nanowire array on the substrate. The p-i-n a-Si solar cell structure is grown along the surface of each ZnO: Al nanowire sequentially. Under sunlight illumination, the light is absorbed in the axis direction of the nanowire. However, the carrier transport is along the radial direction of the solar cell. Therefore, the long nanowire could absorb most of the solar light. In the mean time, the thickness of the solar cell still is thin enough for photo-generated carrier transport. The dependence of short circuit current, open circuit voltage and fill factor to the length, diameter and density of ZnO:Al nanowires were simulated.

CHARACTERISTICS OF PHOSPHORUS-DOPED AMORPHOUS CARBON FILMS GROWN BY R. F. PLASMA-ENHANCED CVD WITH A NOVEL PHOSPHORUS SOLID TARGET

2005 ◽  
Vol 12 (01) ◽  
pp. 19-25 ◽  
Author(s):  
M. RUSOP ◽  
M. ADACHI ◽  
T. SOGA ◽  
T. JIMBO
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Amorphous Carbon ◽  
Current Density ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Phosphorus Doped

Phosphorus-doped amorphous carbon (n-C:P) films were grown by r. f.-power-assisted plasma-enhanced chemical vapor deposition at room temperature using a novel solid red phosphorus target. The influence of phosphorus doping on material properties of n-C:P based on the results of simultaneous characterization are reported. Moreover, the solar cell properties such as series resistance, short circuit current density, open circuit current voltage, fill factor and conversion efficiency along with the spectral response are reported for the fabricated carbon-based n-C:P/p-Si heterojunction solar cell that was measured by standard measurement technique. The cells performances have been given in the dark I–V rectifying curve and I–V working curve under illumination when exposed to AM 1.5 illumination condition (100 mW/cm 2, 25°C). The maximum of open-circuit voltage (V oc ) and short-circuit current density (J sc ) for the cells are observed to be approximately 236 V and 7.34, mAcm 2 respectively for the n-C:P/p-Si cell grown at lower r. f. power of 100 W. The highest energy conversion efficiency (η) and fill factor (FF) were found to be approximately 0.84% and 49%, respectively. We have observed that the rectifying nature of the heterojunction structures is due to the nature of n-C:P films.

Characteristics of Dye-Sensitized Solar Cells Using Dye from Pitaya Fruit

2015 ◽  
Vol 793 ◽  
pp. 450-454 ◽  
Author(s):  
N. Gomesh ◽  
R. Syafinar ◽  
Muhamad Irwanto ◽  
Y.M. Irwan ◽  
M. Fareq ◽  
...  
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Liquid Electrolyte ◽  
Open Circuit ◽  
Dye Sensitized Solar Cell ◽  
Photoelectrochemical Performance ◽  
Cell Efficiency ◽  
Dye Sensitized

Dye-sensitized solar cell (DSSC) consists of TiO2 nanoporous coating which acts as a photo electrode, a sensitizer of dye molecules soaked in the TiO2 film, liquid electrolyte and a counter electrode. This paper focuses on the usage of a sensitizer from the Pitaya fruit. Pitaya or commonly known as dragon fruit (Hylocereus polyrhizus) was extracted and used as a sensitizer to fabricate the dye sensitized solar cell (DSSC). The photoelectrochemical performance of Pitaya based solar cell shows an open circuit voltage (VOC) of 237 mV, short circuit current (ISC) of 4.98 mA, fill factor (FF) of 0.51, solar cell efficiency (η) of 0.70 % and has a peak absorbance rate of 2.7 at 550 nm. The photoelectrochemical and UV-Visible light absorbance performance of Pitaya-DSSC shows good potential in future solar cell fabrication.

scholarly journals Measurement Uncertainty Propagation through Basic Photovoltaic Cell Models

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1029 ◽  
Author(s):  
Ivan Tolić ◽  
Mario Primorac ◽  
Kruno Miličević
Keyword(s):  
Measurement Uncertainty ◽  
Fill Factor ◽  
Short Circuit ◽  
Renewable Energy Sources ◽  
Uncertainty Propagation ◽  
Short Circuit Current ◽  
Photovoltaic Cell ◽  
Open Circuit ◽  
Cell Models ◽  
Global Irradiance

This paper presents measurement uncertainty propagation through four basic photovoltaic cell models: One-diode model without resistances, with one resistance and with two resistances and two-diode model with two resistances. The expressions for the output current of all photovoltaic cell models is presented as a function of global irradiance G and temperature T. Next, the expressions for all fill factor parameters: short-circuit current, open-circuit voltage, current and voltage at the maximum power point, depending on the global irradiance G and temperature T are derived as well. For each parameter, Monte Carlo simulations to calculate the measurement uncertainty of the parameter are performed and the results were used as input values for the calculation of measurement uncertainty of fill factor. Practical calculations are performed in laboratory for renewable energy sources located on 45°32′ N and 18°44′ E. Final fill factor calculations are compared for three different module technologies.

In Situ Quaternized Gel Electrolyte for Quasi-Solid-State Dye-Sensitized Solar Cell

2011 ◽  
Vol 415-417 ◽  
pp. 1586-1589
Author(s):  
Yu Hua Dai ◽  
Xiao Lei Sun ◽  
Jing Lian Wang ◽  
Ming Shan Yang
Keyword(s):  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Liquid Electrolyte ◽  
Open Circuit ◽  
Gel Electrolyte ◽  
Dye Sensitized Solar Cell ◽  
Dye Sensitized

A series of copolymers P(VP-HEMA) composed of hydroxyl ethyl methacrylate (HEMA) and 4-vinyl pyridine (VP) were prepared by a solution copolymerization technique. Based on the copolymer P(VP-HEMA) prepared by the content of VP 50%, the amount of AIBN 3% and the optimized liquid electrolyte, a polymer solution electrolyte with concentration of 9.0% was formed. By addition of 1,4-dibromobutane into the solution, the copolymer gel electrolyte with higher conductivity 6.14mS/cm was prepared. Gelation is caused by the quaterisation between the group of pyridine in P(HEMA-VP) and 1,4-dibromobutane. Based on the copolymer gel electrolyte, a dye-sensitized solar cell was fabricated with short-circuit current of 13.62mA/cm2,open circuit voltage of 0.72V, fill factor of 0.5465 and an overall conversion efficiency of 5.24% under irradiation 100mW/cm2(AM1.5).

scholarly journals Efficiency enhancement of natural dye sensitized solar cell by optimizing electrode fabrication parameters

2018 ◽  
Vol 35 (4) ◽  
pp. 816-823 ◽  
Author(s):  
M. Khalid Hossain ◽  
M.F. Pervez ◽  
S. Tayyaba ◽  
M. Jalal Uddin ◽  
A.A. Mortuza ◽  
...  
Keyword(s):  
Solar Cell ◽  
Counter Electrode ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized Solar Cell ◽  
Cell Efficiency ◽  
Dye Sensitized ◽  
Candle Flame

Abstract Efficiency of dye-sensitized solar cell (DSSC) depends on several interrelated factors such as type and concentration of dye, type and thickness of photoelectrode and counter electrode. Optimized combination of these factors leads to a more efficient cell. This paper presents the effect of these parameters on cell efficiency. TiO2 nanoporous thin films of different thicknesses (5 μm to 25 μm) were fabricated on indium doped tin oxide (ITO) coated glass by doctor blading method and characterized by inverted microscope, stylus surface profiler and scanning electron microscope (SEM). Natural organic dye of different concentrations, extracted from turmeric, was prepared with ethanol solvent. Different combinations of dye concentrations and film thicknesses along with different types of carbon catalyst have been investigated by I-V characterization. The result shows that the cell made of a counter electrode catalyst material prepared by candle flame carbon combined with about 15 μm thick photoelectrode and 100 mg/mL dye in ethanol solvent, achieves the highest efficiency of 0.45 %, with open circuit voltage of 566 mV and short circuit current density of 1.02 mA/cm2.

Sign in / Sign up

Export Citation Format

Share Document