scholarly journals Biosurfactan Injection of “U-Champ” on Heavy Oil Sample in Laboratory for Preliminary to Pilot Project

2020 ◽  
Vol 9 (4) ◽  
pp. 46-50
Keyword(s):  
Interfacial Tension ◽  
Laboratory Experiment ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Pilot Project ◽  
Recovery Factor ◽  
Fluid Characteristics

Biosurfactants “U-Champ” is made by microorganisms, it could be changes the fluid characteristics which are, viscosity and Interfacial tension (IFT). In this study, will be presented the effect of Biosurfactan “U-Champ” injection into the heavy oil sample on laboratory experiment. Viscosity and IFT measurement was carried out in this experiment to analyze the characteristic changes. Coreflooding experiment also occur to measure the incremental of oil recovery. We used some of concetration of Biousrfactant “U-Champ” (1%;2,5%;5%;10%). In this experiment, we found 5% concetration of Biosurfactant “U-Champ” as the CMC value. The result of observation indicates the reduction of viscosity from 5.57 cp to 1.76 cp at 30oC, and from 1 cp to 0.95 cp at 80oC, and reduced the IFT value from 10.05 mN/m to 3.81 mN/m. Based on the result, Coreflooding experiment was occur to measure the incremental of oil recovery and obtained the increasing of recovery factor from 37,5% after waterflooding process to 81,25%. Finally, this studies feasible to continue in pilot project.

Pilot Project Evaluating WAG Efficiency for Carbonate Reservoir in Eastern Siberia

2021 ◽  
Author(s):  
Valentina Zharko ◽  
Dmitriy Burdakov
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Oil Production ◽  
Pilot Project ◽  
Carbonate Reservoir ◽  
Recovery Factor ◽  
Eastern Siberia ◽  
Water Cut ◽  
Wag Injection ◽  
Injection Rates

Abstract The paper presents the results of a pilot project implementing WAG injection at the oilfield with carbonate reservoir, characterized by low efficiency of traditional waterflooding. The objective of the pilot project was to evaluate the efficiency of this enhanced oil recovery method for conditions of the specific oil field. For the initial introduction of WAG, an area of the reservoir with minimal potential risks has been identified. During the test injections of water and gas, production parameters were monitored, including the oil production rates of the reacting wells and the water and gas injection rates of injection wells, the change in the density and composition of the produced fluids. With first positive results, the pilot area of the reservoir was expanded. In accordance with the responses of the producing wells to the injection of displacing agents, the injection rates were adjusted, and the production intensified, with the aim of maximizing the effect of WAG. The results obtained in practice were reproduced in the simulation model sector in order to obtain a project curve characterizing an increase in oil recovery due to water-alternating gas injection. Practical results obtained during pilot testing of the technology show that the injection of gas and water alternately can reduce the water cut of the reacting wells and increase overall oil production, providing more efficient displacement compared to traditional waterflooding. The use of WAG after the waterflooding provides an increase in oil recovery and a decrease in residual oil saturation. The water cut of the produced liquid decreased from 98% to 80%, an increase in oil production rate of 100 tons/day was obtained. The increase in the oil recovery factor is estimated at approximately 7.5% at gas injection of 1.5 hydrocarbon pore volumes. Based on the received results, the displacement characteristic was constructed. Methods for monitoring the effectiveness of WAG have been determined, and studies are planned to be carried out when designing a full-scale WAG project at the field. This project is the first pilot project in Russia implementing WAG injection in a field with a carbonate reservoir. During the pilot project, the technical feasibility of implementing this EOR method was confirmed, as well as its efficiency in terms of increasing the oil recovery factor for the conditions of the carbonate reservoir of Eastern Siberia, characterized by high water cut and low values of oil displacement coefficients during waterflooding.

Indoor Study of Viscosity Reducer for Thickened Oil of Huancai

2012 ◽  
Vol 268-270 ◽  
pp. 547-550
Author(s):  
Qing Wang Liu ◽  
Xin Wang ◽  
Zhen Zhong Fan ◽  
Jiao Wang ◽  
Rui Gao ◽  
...  
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Heavy Oil ◽  
High Viscosity ◽  
Oil Field ◽  
Viscosity Reduction ◽  
Oil Viscosity ◽  
Low Viscosity ◽  
Viscosity Reducer ◽  
Oil Water

Liaohe oil field block 58 for Huancai, the efficiency of production of thickened oil is low, and the efficiency of displacement is worse, likely to cause other issues. Researching and developing an type of Heavy Oil Viscosity Reducer for exploiting. The high viscosity of W/O emulsion changed into low viscosity O/W emulsion to facilitate recovery, enhanced oil recovery. Through the experiment determine the viscosity properties of Heavy Oil Viscosity Reducer. The oil/water interfacial tension is lower than 0.0031mN•m-1, salt-resisting is good. The efficiency of viscosity reduction is higher than 90%, and also good at 180°C.

Improvement of Displacement Efficiency in Heavy Oil Reservoirs with Enzyme

2021 ◽  
pp. 1-30
Author(s):  
Yu Shi ◽  
Yanan Ding ◽  
Qianghan Feng ◽  
Daoyong Yang
Keyword(s):  
Oil Recovery ◽  
Heavy Oil ◽  
Contact Time ◽  
Enzyme Concentration ◽  
Oil Reservoirs ◽  
Recovery Factor ◽  
Displacement Efficiency ◽  
Oil Viscosity ◽  
Enzyme Solution ◽  
Heavy Oil Reservoirs

Abstract In this study, a systematical technique has been developed to experimentally and numerically evaluate the displacement efficiency in heavy oil reservoirs with enzyme under different conditions. Firstly, dynamic interfacial tensions (IFTs) between enzyme solution and heavy oil are measured with a pendant-drop tensiometer, while effects of pressure, temperature, enzyme concentration, and contact time of enzyme and heavy oil on equilibrium IFT were systematically examined and analyzed. After waterflooding, enzyme flooding was carried out in sandpacks to evaluate its potential to enhance heavy oil recovery at high water-cut stage. Numerical simulation was then performed to identify the underlying mechanisms accounting for the enzyme flooding performance. Subsequently, a total of 18 scenarios were designed to simulate and examine effects of the injection modes and temperature on oil recovery. Except for pressure, temperature, enzyme concentration, and contact time are found to impose a great impact on the equilibrium IFTs, i.e., a high temperature, a high enzyme concentration, and a long contact time reduce the equilibrium IFTs. All three enzyme flooding tests with different enzyme concentrations show the superior recovery performance in comparison to that of pure waterflooding. In addition to the IFT reduction, modification of relative permeability curves is found to be the main reason responsible for further mobilizing the residual heavy oil. A large slug size of enzyme solution usually leads to a high recovery factor, although its incremental oil production is gradually decreased. Plus, temperature is found to have a great effect on the recovery factor of enzyme flooding likely owing to reduction of both oil viscosity and IFT.

Applied Research of Heat Self-Generated CO2 Technology in Steam Huff and Puff

2014 ◽  
Vol 1010-1012 ◽  
pp. 1693-1698
Author(s):  
Yi Ding ◽  
Guo Wei Qin ◽  
Peng Liu ◽  
Zi Li Fan ◽  
Hong Wei Xiao ◽  
...  
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Field Experiments ◽  
Reduction Rate ◽  
Viscosity Reduction ◽  
Oil Viscosity ◽  
Blowing Agent ◽  
Steam Flooding ◽  
Gas Flooding

Heat self-generated CO2 technique is proposed, which is focused on the problems of recovery difficulty, poor effect steam soaking and so on for heavy oil reservoirs. This technology is combining of steam flooding and gas flooding and so on. Its main mechanism is the application of steam heating blowing agent to generate a large volume of gases (including CO2, NH3, etc) in the formation. While some of these gases acting with the oil to reduce the oil viscosity, some form miscible flooding to reduce water interfacial tension, so as to achieve the purpose of enhancing oil recovery. An optimized selection of the heat blowing agents was performed. By comparison the difference before and after the reaction of blowing agent solution, the increase of alkaline is occurred after the reaction, and is helpful to reduce oil viscosity and lower interfacial tension, etc. Studies indicate that heat-generating CO2 flooding technology can get a maximum viscosity reduction rate of 76.7%, oil-water interfacial tension decreased by 54.77%, further improve oil recovery by 4.17% based on the steam drive, which shows a technical advantage toward conventional EOR method. The field experiments indicate that the technique can greatly improve the oil production, which will provide a powerful technical supporting for the efficient development of heavy oil.

Foam Flooding with Ultra-Low Interfacial Tension to Enhance Heavy Oil Recovery

2014 ◽  
Vol 35 (3) ◽  
pp. 403-410 ◽  
Author(s):  
Shuo Zhang ◽  
Guan-Cheng Jiang ◽  
Le Wang ◽  
Hai-Tao Guo ◽  
Xin-guo Tang ◽  
...  
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Heavy Oil Recovery ◽  
Low Interfacial Tension ◽  
Foam Flooding
Sign in / Sign up

Export Citation Format

Share Document