Effect of Carbon Dioxide Injection on the Mechanical Properties of Synthetic Brown Coal

Author(s):  
Dileeka Jasinge ◽  
Pathegama Ranjith ◽  
Sing Choi ◽  
Jayantha Kodikara
2019 ◽  
Vol 2 (3) ◽  
pp. 141-151
Author(s):  
O. E. Gnezdova ◽  
E. S. Chugunkova

Introduction: greenhouses need microclimate control systems to grow agricultural crops. The method of carbon dioxide injection, which is currently used by agricultural companies, causes particular problems. Co-generation power plants may boost the greenhouse efficiency, as they are capable of producing electric energy, heat and cold, as well as carbon dioxide designated for greenhouse plants.Methods: the co-authors provide their estimates of the future gas/electricity rates growth in the short term; they have made a breakdown of the costs of greenhouse products, and they have also compiled the diagrams describing electricity consumption in case of traditional and non-traditional patterns of power supply; they also provide a power distribution pattern typical for greenhouse businesses, as well as the structure and the principle of operation of a co-generation unit used by a greenhouse facility.Results and discussion: the co-authors highlight the strengths of co-generation units used by greenhouse facilities. They have also identified the biological features of carbon dioxide generation and consumption, and they have listed the consequences of using carbon dioxide to enrich vegetable crops.Conclusion: the co-authors have formulated the expediency of using co-generation power plants as part of power generation facilities that serve greenhouses.


2018 ◽  
Vol 216 ◽  
pp. 03001 ◽  
Author(s):  
Evgeny Ivanayskiy ◽  
Aleksei Ishkov ◽  
Aleksandr Ivanayskiy ◽  
Iakov Ochakovskii

The paper studies the influence of shielding gas on the composition and the structure of weld joint metal of 30MnB5 steel applied in essential parts of automobiles and tractors. The welding was performed in inert, oxidizing and reducing atmospheres. It was established that TIG welding with argon used as shielding gas did not provide the required mechanical properties when using conventional welding materials. Carbon dioxide during MAG welding caused partial burning of alloying elements. Carbon monoxide used as shielding gas was proved to form reducing atmosphere enabling to obtain chemical composition close to the base metal composition. Metallographic examinations were carried out. The obtained results provided full-strength weld, as well as the required reliability and durability of welded components and joints.


2017 ◽  
Vol 883 ◽  
pp. 75-84 ◽  
Author(s):  
Nireeksha Karode ◽  
Laurence Fitzhenry ◽  
Siobhán Matthews ◽  
Philip Walsh ◽  
Austin Coffey

Medical tubing used in minimally invasive devices presents a number of design considerations depending on the material used, design requirements (such as sufficient stiffness, flexibility and biocompatibility) and processing conditions. Currently, manufacturing industries adopt co-extrusion systems to meet design specifications, by using multilayer configuration leading to higher cost per device and increased complexity. This paper investigates the mechanical performance of nanocomposites using supercritical carbon dioxide assisted polymer processing technique. The use of innovative medical compounds such as PEBAX graphene nanocomposites have resulted in measurable improvements in mechanical properties. This study also presents the effect of supercritical carbon dioxide on the mechanical and physical properties of the polymer matrix. The mechanical properties have been investigated using dynamic mechanical analysis (DMA) and mechanical tensile test, where sufficient reinforcement was observed depending on the composition of graphene within PEBAX matrix. ATR-FTIR was used to further analyze the effect of supercritical carbon dioxide and interactions within the polymer composite matrix.


2013 ◽  
Vol 46 ◽  
pp. 201-209 ◽  
Author(s):  
Weiguo Liu ◽  
Jiafei Zhao ◽  
Yuan Luo ◽  
Yongchen Song ◽  
Yanghui Li ◽  
...  

2013 ◽  
Vol 856 ◽  
pp. 338-342 ◽  
Author(s):  
Chin Yee Sing ◽  
Mohd Shiraz Aris

Burning fossil fuel like coal in power plants released carbon dioxide that had been absorbed millions of years ago. Unfortunately, excessive carbon dioxide emission had led to global warming. Malaysia, as one of the major exporters of palm oil, has abundant oil palm mill residues that could be converted into value-added product like biomass fuel briquettes. Fuel briquette with palm kernel shell and palm mesocarp fibre as its main ingredients showed satisfactory fuel characteristics and mechanical properties as a pure biomass fuel briquette. The effects of adding some coal of higher calorific value to the satisfactory biomass fuel briquette were focused in this study. Various coal-biomass fuel blends were used, ranging from 0wt% coal to 50wt% coal. The fuel properties and mechanical properties of pure biomass briquette and briquettes with different amount of coal added were compared experimentally. From the fuel properties tests, it was found that as the coal content in the briquette was increased, the carbon content and calorific value increased. Mechanical property tests on the fuel briquettes showed a mixture of results, with some favored higher portion of coal in the briquette for better handling, transport and storage properties while some favored greater amount of biomass.


Sign in / Sign up

Export Citation Format

Share Document