scholarly journals Application of 3D Laser Scanning for Digitization, Design and Analysis of Multistoried Building

2021 ◽  
Author(s):  
Abdul Qadir Bhatti ◽  
◽  
Abdul Wahab ◽  
Wadea Sindi ◽  
◽  
...  
Keyword(s):  
Structural Damage ◽  
Point Cloud ◽  
Laser Scanning ◽  
Passive Control ◽  
Complex Geometry ◽  
Laser Scanner ◽  
Point Clouds ◽  
Historical Building ◽  
Laser Scanners ◽  
Original Construction

Laser scanning is a fast-developing technology, which collects millions of points and creates a framework within a few minutes, generating a 'point cloud' of the structure. Laser scanning is a quite new but rapidly evolving technology that has been reviewed. this research study has used most modern models of laser scanners and their accompanying software that are capable of accurate capture and alignment of point clouds. Consequently, the laser scans have precisely captured the current geometry of each structure, which is irregular in many cases due to inherently complex geometry, anomalies during the original construction, aging, deterioration, and structural damage. As both the exterior and interior of the structure have been scanned, the point cloud became a digital 3D image of the historical building, which can be virtually toured from inside and outside. A 4-story public building was scanned using a 3D laser scanner to determine the architectural and structural drawings of the response to an earthquake. The application of passive control using a damper with the laser scanner has been modelled in this study. The results corroborate that this technique provides the best outcomes for reducing seismic damage collapses.

Influence of ULS data acquisition characteristics on the achievable stem reconstruction accuracies

2020 ◽  
Author(s):  
Moritz Bruggisser ◽  
Johannes Otepka ◽  
Norbert Pfeifer ◽  
Markus Hollaus
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Stem Diameter ◽  
Forest Monitoring ◽  
Individual Tree ◽  
Detection Rates ◽  
Point Count ◽  
Tree Stem

<p>Unmanned aerial vehicles-borne laser scanning (ULS) allows time-efficient acquisition of high-resolution point clouds on regional extents at moderate costs. The quality of ULS-point clouds facilitates the 3D modelling of individual tree stems, what opens new possibilities in the context of forest monitoring and management. In our study, we developed and tested an algorithm which allows for i) the autonomous detection of potential stem locations within the point clouds, ii) the estimation of the diameter at breast height (DBH) and iii) the reconstruction of the tree stem. In our experiments on point clouds from both, a RIEGL miniVUX-1DL and a VUX-1UAV, respectively, we could detect 91.0 % and 77.6 % of the stems within our study area automatically. The DBH could be modelled with biases of 3.1 cm and 1.1 cm, respectively, from the two point cloud sets with respective detection rates of 80.6 % and 61.2 % of the trees present in the field inventory. The lowest 12 m of the tree stem could be reconstructed with absolute stem diameter differences below 5 cm and 2 cm, respectively, compared to stem diameters from a point cloud from terrestrial laser scanning. The accuracy of larger tree stems thereby was higher in general than the accuracy for smaller trees. Furthermore, we recognized a small influence only of the completeness with which a stem is covered with points, as long as half of the stem circumference was captured. Likewise, the absolute point count did not impact the accuracy, but, in contrast, was critical to the completeness with which a scene could be reconstructed. The precision of the laser scanner, on the other hand, was a key factor for the accuracy of the stem diameter estimation. <br>The findings of this study are highly relevant for the flight planning and the sensor selection of future ULS acquisition missions in the context of forest inventories.</p>

scholarly journals POTENTIAL OF FULL WAVEFORM AIRBORNE LASER SCANNING DATA FOR URBAN AREA CLASSIFICATION – TRANSFER OF CLASSIFICATION APPROACHES BETWEEN MISSIONS

2015 ◽  
Vol XL-7/W3 ◽  
pp. 1317-1323 ◽  
Author(s):  
G. Tran ◽  
D. Nguyen ◽  
M. Milenkovic ◽  
N. Pfeifer
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Surface Model ◽  
Knowledge Based ◽  
Full Waveform ◽  
Airborne Laser ◽  
Point Density ◽  
Area Classification

Full-waveform (FWF) LiDAR (Light Detection and Ranging) systems have their advantage in recording the entire backscattered signal of each emitted laser pulse compared to conventional airborne discrete-return laser scanner systems. The FWF systems can provide point clouds which contain extra attributes like amplitude and echo width, etc. In this study, a FWF data collected in 2010 for Eisenstadt, a city in the eastern part of Austria was used to classify four main classes: buildings, trees, waterbody and ground by employing a decision tree. Point density, echo ratio, echo width, normalised digital surface model and point cloud roughness are the main inputs for classification. The accuracy of the final results, correctness and completeness measures, were assessed by comparison of the classified output to a knowledge-based labelling of the points. Completeness and correctness between 90% and 97% was reached, depending on the class. While such results and methods were presented before, we are investigating additionally the transferability of the classification method (features, thresholds …) to another urban FWF lidar point cloud. Our conclusions are that from the features used, only echo width requires new thresholds. A data-driven adaptation of thresholds is suggested.

scholarly journals INDOOR MAPPING OF A COMPLEX CULTURAL HERITAGE SCENE USING TLS AND HMLS LASER SCANNING

2021 ◽  
Vol XLIII-B2-2021 ◽  
pp. 605-612
Author(s):  
V. E. Oniga ◽  
A. I. Breaban ◽  
E. I. Alexe ◽  
C. Văsii
Keyword(s):  
Standard Deviation ◽  
Cultural Heritage ◽  
Long Range ◽  
Interior Design ◽  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Acquisition Time ◽  
Wide Range

Abstract. Indoor mapping and modelling is an important research subject with application in a wide range of domains including interior design, real estate, cultural heritage conservation and restoration. There are multiple sensors applicable for 3D indoor modelling, but the laser scanning technique is frequently used because of the acquisition time, detailed information and accuracy. In this paper, the efficiency of the Maptek I-Site 8820 terrestrial scanner, which is a long-range laser scanner and the accuracy of a HMLS point cloud acquired with a mobile scanner, namely GeoSlam Zeb Horizon were tested for indoor mapping. Aula Magna “Carmen Silva” of the “Gheorghe Asachi” Technical University of Iasi is studied in the current paper since the auditorium interior creates a distinct environment that combines complex geometric structures with architectural lighting and for preserving its great cultural value, the monument has a national historical significance. The registration process of the TLS point clouds was done using two methods: a semi-automatic one with artificial targets and a completely automatic one, based on Iterative Closest Point (ICP) algorithm. The resulted TLS point cloud was analysed in relation to the HMLS point cloud by computing the M3C2 (Multiscale Model to Model Cloud Comparison), obtaining a standard deviation of 2.1 cm and by investigating the Hausdorff distances from which resulted a standard deviation (σ) of 1.6 cm. Cross-sections have been extracted from the HMLS and TLS point clouds and after comparing the sections, 80% of the sigma values are less or equal to 1 cm. The results show high potential of using HMLS and also a long-range laser scanner for 3D modelling of complex scenes, the occlusion effect in the case of TLS being only 5% of the scanned area.

scholarly journals Reality Capture of Buildings Using 3D Laser Scanners

2021 ◽  
Author(s):  
Avar Almukhtar ◽  
Henry Abanda ◽  
Zaid O. Saeed ◽  
Joseph H.M. Tah
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Construction Project ◽  
Laser Scanner ◽  
Data File ◽  
Point Cloud Data ◽  
Cloud Data ◽  
Laser Scanners ◽  
Project Data

The urgent need to improve performance in the construction industry has led to the adoption of many innovative technologies. 3D laser scanners are amongst the leading technologies being used to capture and process assets or construction project data for use in various applications. Due to its nascent nature, many questions are still unanswered about 3D laser scanning, which in turn contribute to the slow adaptation of the technology. Some of these include the role of 3D laser scanners in capturing and processing raw construction project data. How accurate is the 3D laser scanner or point cloud data? How does laser scanning fit with other wider emerging technologies such as Building Information Modelling (BIM)? This study adopts a proof-of-concept approach, which in addition to answering the afore-mentioned questions, illustrates the application of the technology in practice. The study finds that the quality of the data, commonly referred to as point cloud data is still a major issue as it depends on the distance between the target object and 3D laser scanner’s station. Additionally, the quality of the data is still very dependent on data file sizes and the computational power of the processing machine. Lastly, the connection between laser scanning and BIM approaches is still weak as what can be done with a point cloud data model in a BIM environment is still very limited. The aforementioned findings reinforce existing views on the use of 3D laser scanners in capturing and processing construction project data.

The Advantages of Using Laser Scanners in Surveying in Protected Sites

2015 ◽  
pp. 382-402
Author(s):  
Gülhan Benli
Keyword(s):  
Protected Areas ◽  
Point Cloud ◽  
Laser Scanning ◽  
Three Dimensional ◽  
Terrestrial Laser Scanning ◽  
Point Clouds ◽  
Point Cloud Data ◽  
Cloud Data ◽  
Laser Scanners ◽  
Point Data

Since the 2000s, terrestrial laser scanning, as one of the methods used to document historical edifices in protected areas, has taken on greater importance because it mitigates the difficulties associated with working on large areas and saves time while also making it possible to better understand all the particularities of the area. Through this technology, comprehensive point data (point clouds) about the surface of an object can be generated in a highly accurate three-dimensional manner. Furthermore, with the proper software this three-dimensional point cloud data can be transformed into three-dimensional rendering/mapping/modeling and quantitative orthophotographs. In this chapter, the study will present the results of terrestrial laser scanning and surveying which was used to obtain three-dimensional point clouds through three-dimensional survey measurements and scans of silhouettes of streets in Fatih in Historic Peninsula in Istanbul, which were then transposed into survey images and drawings. The study will also cite examples of the facade mapping using terrestrial laser scanning data in Istanbul Historic Peninsula Project.

Replica Fabrication of a Greek Paleontological Find Utilising Laser Scanning and Fused Deposition Modeling

2014 ◽  
Vol 657 ◽  
pp. 795-799 ◽  
Author(s):  
Anastasios Chatzikonstantinou ◽  
Dimitrios Tzetzis ◽  
Panagiotis Kyratsis ◽  
Nikolaos Bilalis
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Fused Deposition Modeling ◽  
Complex Geometry ◽  
Low Cost ◽  
Three Dimensional ◽  
Laser Scanner ◽  
Analytical Methodology ◽  
Fused Deposition ◽  
Deposition Modeling

The current work demonstrates a feasibility study on the generation of a copy, having a highly complex geometry, of a Greek paleontological find utilising reverse engineering and low-cost rapid prototyping techniques. A part of the jaw bone of a cave bear (Ursus spelaeus) that lived during the Pleistocene and became extinct about 10,000 years ago was digitized using a three-dimensional laser scanner. The resulting point-cloud of the scans was treated with a series of advanced software for the creation of surfaces and ultimately for a digital model. The generated model was three-dimensionally built by the aid of a Fused Deposition Modeling (FDM) apparatus. An analytical methodology is presented revealing the step by step approach from the scanning to the prototyping. It is believed that a variety of interested parties could benefit from such an analytical approach, including, production engineers, three-dimensional CAD users and designers, paleontologists and museum curators.

scholarly journals System analysis of the quality of meshes in HBIM

2018 ◽  
Vol 170 ◽  
pp. 03033 ◽  
Author(s):  
Elizaveta Fateeva ◽  
Vladimir Badenko ◽  
Alexandr Fedotov ◽  
Ivan Kochetkov
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
System Analysis ◽  
Point Clouds ◽  
Rational Solutions ◽  
Historical Building ◽  
Architectural Styles ◽  
Architectural Features ◽  
Building Information

Historical Building Information Modelling (HBIM) is nowadays used as a means to collect, store and preserve information about historical buildings and structures. The information is often collected via laser scanning. The resulting point cloud is manipulated and transformed into a polygon mesh, which is a type of model very easy to work with. This paper looks at the problems associated with creating mesh out of point clouds depending on various characteristics in context of façade reconstruction. The study is based on a point cloud recorded via terrestrial laser scanning in downtown Bremen, Germany that contains buildings completed in a number of different architectural styles, allowing to extract multiple architectural features. Analysis of meshes' quality depending on point cloud density was carried out. Conclusions were drawn as to what the rational solutions for effective surface extraction can be for each individual building in question. Recommendations on preprocessing of point clouds were given.

scholarly journals COMPARISON WITH ACCURACY OF TERRESTRIAL LASER SCANNER BY USING POINT CLOUD ALIGNED WITH SHAPE MATCHING AND BEST FITTING METHODS

2019 ◽  
Vol XLII-2/W9 ◽  
pp. 535-541 ◽  
Author(s):  
T. Ogawa ◽  
Y. Hori
Keyword(s):  
Laser Scanning ◽  
Shape Matching ◽  
Laser Scanner ◽  
Point Clouds ◽  
Random Errors ◽  
Laser Scanners ◽  
Error Distributions ◽  
Best Fitting ◽  
Scan Data ◽  
Fitting In

<p><strong>Abstract.</strong> Recently operation systems of laser scanning have been obviously improved; for instance shape matching has been equipped with software on a post processing stage so measurement without any targets is a prerequisite condition of field surveying with laser scanners. Moreover a shape matching method enables us to easily register a pair of point clouds with some errors even if those data are scanned by several type scanners. Those slightly errors can influence accuracy of alignments if the object is large to require a lot of scans. Laser scanning data has random errors and accuracy of alignments can be improved by matching error distributions of pairs of point clouds to natural distributions. This method is called “best fitting” in contrast “shape matching” in a software, PolyWorks |Inspector. In this paper, accuracy of alignments between shape matching and best fitting is discussed. The scan data of three phaseshift laser scanners (FARO Focus 3D MS120, FARO Focus 3D X330 and Z+F Imager 5016) and two time-of-flight scanners (Leica BLK 360 and Leica Scan station C5) are used for analyses. Accuracy of alignments by using shape matching and best fitting methods is demonstrated by showing points of scan data with histograms of error distributions.</p>

scholarly journals PERSPECTIVE INTENSITY IMAGES FOR CO-REGISTRATION OF TERRESTRIAL LASER SCANNER AND DIGITAL CAMERA

2016 ◽  
Vol XLI-B3 ◽  
pp. 295-300
Author(s):  
Yubin Liang ◽  
Yan Qiu ◽  
Tiejun Cui
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Least Squares Method ◽  
Laser Scanner ◽  
Digital Camera ◽  
Point Clouds ◽  
Terrestrial Laser Scanner ◽  
Automatic Registration ◽  
Intensity Images ◽  
Intensity Image

Co-registration of terrestrial laser scanner and digital camera has been an important topic of research, since reconstruction of visually appealing and measurable models of the scanned objects can be achieved by using both point clouds and digital images. This paper presents an approach for co-registration of terrestrial laser scanner and digital camera. A perspective intensity image of the point cloud is firstly generated by using the collinearity equation. Then corner points are extracted from the generated perspective intensity image and the camera image. The fundamental matrix F is then estimated using several interactively selected tie points and used to obtain more matches with RANSAC. The 3D coordinates of all the matched tie points are directly obtained or estimated using the least squares method. The robustness and effectiveness of the presented methodology is demonstrated by the experimental results. Methods presented in this work may also be used for automatic registration of terrestrial laser scanning point clouds.

scholarly journals COMPARISON OF ZEB1 AND LEICA C10 INDOOR LASER SCANNING POINT CLOUDS

2016 ◽  
Vol III-1 ◽  
pp. 143-149
Author(s):  
Beril Sirmacek ◽  
Yueqian Shen ◽  
Roderik Lindenbergh ◽  
Sisi Zlatanova ◽  
Abdoulaye Diakite
Keyword(s):  
Data Acquisition ◽  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Quality Of Data ◽  
Local Point ◽  
Measurement Planning ◽  
Data Acquisition And Processing

We present a comparison of point cloud generation and quality of data acquired by Zebedee (Zeb1) and Leica C10 devices which are used in the same building interior. Both sensor devices come with different practical and technical advantages. As it could be expected, these advantages come with some drawbacks. Therefore, depending on the requirements of the project, it is important to have a vision about what to expect from different sensors. In this paper, we provide a detailed analysis of the point clouds of the same room interior acquired from Zeb1 and Leica C10 sensors. First, it is visually assessed how different features appear in both the Zeb1 and Leica C10 point clouds. Next, a quantitative analysis is given by comparing local point density, local noise level and stability of local normals. Finally, a simple 3D room plan is extracted from both the Zeb1 and the Leica C10 point clouds and the lengths of constructed line segments connecting corners of the room are compared. The results show that Zeb1 is far superior in ease of data acquisition. No heavy handling, hardly no measurement planning and no point cloud registration is required from the operator. The resulting point cloud has a quality in the order of centimeters, which is fine for generating a 3D interior model of a building. Our results also clearly show that fine details of for example ornaments are invisible in the Zeb1 data. If point clouds with a quality in the order of millimeters are required, still a high-end laser scanner like the Leica C10 is required, in combination with a more sophisticated, time-consuming and elaborative data acquisition and processing approach.

Sign in / Sign up

Export Citation Format

Share Document