scholarly journals POTENTIAL OF FULL WAVEFORM AIRBORNE LASER SCANNING DATA FOR URBAN AREA CLASSIFICATION – TRANSFER OF CLASSIFICATION APPROACHES BETWEEN MISSIONS

2015 ◽  
Vol XL-7/W3 ◽  
pp. 1317-1323 ◽  
Author(s):  
G. Tran ◽  
D. Nguyen ◽  
M. Milenkovic ◽  
N. Pfeifer
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Surface Model ◽  
Knowledge Based ◽  
Full Waveform ◽  
Airborne Laser ◽  
Point Density ◽  
Area Classification

Full-waveform (FWF) LiDAR (Light Detection and Ranging) systems have their advantage in recording the entire backscattered signal of each emitted laser pulse compared to conventional airborne discrete-return laser scanner systems. The FWF systems can provide point clouds which contain extra attributes like amplitude and echo width, etc. In this study, a FWF data collected in 2010 for Eisenstadt, a city in the eastern part of Austria was used to classify four main classes: buildings, trees, waterbody and ground by employing a decision tree. Point density, echo ratio, echo width, normalised digital surface model and point cloud roughness are the main inputs for classification. The accuracy of the final results, correctness and completeness measures, were assessed by comparison of the classified output to a knowledge-based labelling of the points. Completeness and correctness between 90% and 97% was reached, depending on the class. While such results and methods were presented before, we are investigating additionally the transferability of the classification method (features, thresholds …) to another urban FWF lidar point cloud. Our conclusions are that from the features used, only echo width requires new thresholds. A data-driven adaptation of thresholds is suggested.

scholarly journals COMPARISON OF UAV IMAGERY-DERIVED POINT CLOUD TO TERRESTRIAL LASER SCANNER POINT CLOUD

2019 ◽  
Vol IV-2/W5 ◽  
pp. 149-155 ◽  
Author(s):  
S. Peterson ◽  
J. Lopez ◽  
R. Munjy
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Focal Length ◽  
Laser Scanner ◽  
Digital Camera ◽  
Point Clouds ◽  
Surface Model ◽  
Control Points ◽  
Ground Control Points ◽  
Aerial Vehicle

<p><strong>Abstract.</strong> A small unmanned aerial vehicle (UAV) with survey-grade GNSS positioning is used to produce a point cloud for topographic mapping and 3D reconstruction. The objective of this study is to assess the accuracy of a UAV imagery-derived point cloud by comparing a point cloud generated by terrestrial laser scanning (TLS). Imagery was collected over a 320&amp;thinsp;m by 320&amp;thinsp;m area with undulating terrain, containing 80 ground control points. A SenseFly eBee Plus fixed-wing platform with PPK positioning with a 10.6&amp;thinsp;mm focal length and a 20&amp;thinsp;MP digital camera was used to fly the area. Pix4Dmapper, a computer vision based commercial software, was used to process a photogrammetric block, constrained by 5 GCPs while obtaining cm-level RMSE based on the remaining 75 checkpoints. Based on results of automatic aerial triangulation, a point cloud and digital surface model (DSM) (2.5&amp;thinsp;cm/pixel) are generated and their accuracy assessed. A bias less than 1 pixel was observed in elevations from the UAV DSM at the checkpoints. 31 registered TLS scans made up a point cloud of the same area with an observed horizontal root mean square error (RMSE) of 0.006m, and negligible vertical RMSE. Comparisons were made between fitted planes of extracted roof features of 2 buildings and centreline profile comparison of a road in both UAV and TLS point clouds. Comparisons showed an average +8&amp;thinsp;cm bias with UAV point cloud computing too high in two features. No bias was observed in the roof features of the southernmost building.</p>

scholarly journals Regional Modeling of Forest Fuels and Structural Attributes Using Airborne Laser Scanning Data in Oregon

2021 ◽  
Vol 13 (2) ◽  
pp. 261
Author(s):  
Francisco Mauro ◽  
Andrew T. Hudak ◽  
Patrick A. Fekety ◽  
Bryce Frank ◽  
Hailemariam Temesgen ◽  
...  
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Field Measurements ◽  
Point Clouds ◽  
Semiparametric Models ◽  
Airborne Laser Scanning ◽  
Parametric Models ◽  
Fuel Load ◽  
Forest Fuels ◽  
Airborne Laser

Airborne laser scanning (ALS) acquisitions provide piecemeal coverage across the western US, as collections are organized by local managers of individual project areas. In this study, we analyze different factors that can contribute to developing a regional strategy to use information from completed ALS data acquisitions and develop maps of multiple forest attributes in new ALS project areas in a rapid manner. This study is located in Oregon, USA, and analyzes six forest structural attributes for differences between: (1) synthetic (i.e., not-calibrated), and calibrated predictions, (2) parametric linear and semiparametric models, and (3) models developed with predictors computed for point clouds enclosed in the areas where field measurements were taken, i.e., “point-cloud predictors”, and models developed using predictors extracted from pre-rasterized layers, i.e., “rasterized predictors”. Forest structural attributes under consideration are aboveground biomass, downed woody biomass, canopy bulk density, canopy height, canopy base height, and canopy fuel load. Results from our study indicate that semiparametric models perform better than parametric models if no calibration is performed. However, the effect of the calibration is substantial in reducing the bias of parametric models but minimal for the semiparametric models and, once calibrations are performed, differences between parametric and semiparametric models become negligible for all responses. In addition, minimal differences between models using point-cloud predictors and models using rasterized predictors were found. We conclude that the approach that applies semiparametric models and rasterized predictors, which represents the easiest workflow and leads to the most rapid results, is justified with little loss in accuracy or precision even if no calibration is performed.

scholarly journals Segmentation and Multi-Scale Convolutional Neural Network-Based Classification of Airborne Laser Scanner Data

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3347 ◽  
Author(s):  
Zhishuang Yang ◽  
Bo Tan ◽  
Huikun Pei ◽  
Wanshou Jiang
Keyword(s):  
Neural Network ◽  
Convolutional Neural Network ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Region Growing ◽  
Point Clouds ◽  
Classification Method ◽  
Multi Scale ◽  
Airborne Laser

The classification of point clouds is a basic task in airborne laser scanning (ALS) point cloud processing. It is quite a challenge when facing complex observed scenes and irregular point distributions. In order to reduce the computational burden of the point-based classification method and improve the classification accuracy, we present a segmentation and multi-scale convolutional neural network-based classification method. Firstly, a three-step region-growing segmentation method was proposed to reduce both under-segmentation and over-segmentation. Then, a feature image generation method was used to transform the 3D neighborhood features of a point into a 2D image. Finally, feature images were treated as the input of a multi-scale convolutional neural network for training and testing tasks. In order to obtain performance comparisons with existing approaches, we evaluated our framework using the International Society for Photogrammetry and Remote Sensing Working Groups II/4 (ISPRS WG II/4) 3D labeling benchmark tests. The experiment result, which achieved 84.9% overall accuracy and 69.2% of average F1 scores, has a satisfactory performance over all participating approaches analyzed.

scholarly journals MULTISPECTRAL AIRBORNE LASER SCANNING FOR AUTOMATED MAP UPDATING

2016 ◽  
Vol XLI-B3 ◽  
pp. 323-330 ◽  
Author(s):  
Leena Matikainen ◽  
Juha Hyyppä ◽  
Paula Litkey
Keyword(s):  
Change Detection ◽  
Laser Scanning ◽  
Point Clouds ◽  
Airborne Laser Scanning ◽  
Aerial Images ◽  
Sensor Technology ◽  
Classification Error ◽  
Surface Model ◽  
Airborne Laser ◽  
Map Updating

During the last 20 years, airborne laser scanning (ALS), often combined with multispectral information from aerial images, has shown its high feasibility for automated mapping processes. Recently, the first multispectral airborne laser scanners have been launched, and multispectral information is for the first time directly available for 3D ALS point clouds. This article discusses the potential of this new single-sensor technology in map updating, especially in automated object detection and change detection. For our study, Optech Titan multispectral ALS data over a suburban area in Finland were acquired. Results from a random forests analysis suggest that the multispectral intensity information is useful for land cover classification, also when considering ground surface objects and classes, such as roads. An out-of-bag estimate for classification error was about 3% for separating classes asphalt, gravel, rocky areas and low vegetation from each other. For buildings and trees, it was under 1%. According to feature importance analyses, multispectral features based on several channels were more useful that those based on one channel. Automatic change detection utilizing the new multispectral ALS data, an old digital surface model (DSM) and old building vectors was also demonstrated. Overall, our first analyses suggest that the new data are very promising for further increasing the automation level in mapping. The multispectral ALS technology is independent of external illumination conditions, and intensity images produced from the data do not include shadows. These are significant advantages when the development of automated classification and change detection procedures is considered.

scholarly journals ON A KNOWLEDGE-BASED APPROACH TO THE CLASSIFICATION OF MOBILE LASER SCANNING POINT CLOUDS

2018 ◽  
Vol XLII-4 ◽  
pp. 343-349 ◽  
Author(s):  
M. Lemmens
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Decision Rules ◽  
Point Clouds ◽  
Bench Mark ◽  
Automated Classification ◽  
Initial Experiment ◽  
Data Set ◽  
Knowledge Based

<p><strong>Abstract.</strong> A knowledge-based system exploits the knowledge, which a human expert uses for completing a complex task, through a database containing decision rules, and an inference engine. Already in the early nineties knowledge-based systems have been proposed for automated image classification. Lack of success faded out initial interest and enthusiasm, the same fate neural networks struck at that time. Today the latter enjoy a steady revival. This paper aims at demonstrating that a knowledge-based approach to automated classification of mobile laser scanning point clouds has promising prospects. An initial experiment exploiting only two features, height and reflectance value, resulted in an overall accuracy of 79<span class="thinspace"></span>% for the Paris-rue-Madame point cloud bench mark data set.</p>

scholarly journals ANALYSIS OF 3D BUILDING MODELS ACCURACY BASED ON THE AIRBORNE LASER SCANNING POINT CLOUDS

2018 ◽  
Vol XLII-2 ◽  
pp. 797-804 ◽  
Author(s):  
W. Ostrowski ◽  
M. Pilarska ◽  
J. Charyton ◽  
K. Bakuła
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Large Scale ◽  
Point Clouds ◽  
3D Models ◽  
Airborne Laser Scanning ◽  
Aerial Images ◽  
Statistical Parameters ◽  
Airborne Laser ◽  
Building Models

Creating 3D building models in large scale is becoming more popular and finds many applications. Nowadays, a wide term “3D building models” can be applied to several types of products: well-known CityGML solid models (available on few Levels of Detail), which are mainly generated from Airborne Laser Scanning (ALS) data, as well as 3D mesh models that can be created from both nadir and oblique aerial images. City authorities and national mapping agencies are interested in obtaining the 3D building models. Apart from the completeness of the models, the accuracy aspect is also important. Final accuracy of a building model depends on various factors (accuracy of the source data, complexity of the roof shapes, etc.). In this paper the methodology of inspection of dataset containing 3D models is presented. The proposed approach check all building in dataset with comparison to ALS point clouds testing both: accuracy and level of details. Using analysis of statistical parameters for normal heights for reference point cloud and tested planes and segmentation of point cloud provides the tool that can indicate which building and which roof plane in do not fulfill requirement of model accuracy and detail correctness. Proposed method was tested on two datasets: solid and mesh model.

Detection of Building in Airborne Laser Scanner Data and Aerial Images

2012 ◽  
Vol 11 ◽  
pp. 7-13
Author(s):  
Dilli Raj Bhandari
Keyword(s):  
Point Cloud ◽  
Laser Scanner ◽  
Aerial Images ◽  
Spectral Information ◽  
Surface Model ◽  
World Population ◽  
Data Sets ◽  
Scanner Data ◽  
Airborne Laser Scanner ◽  
Airborne Laser

The automatic extraction of the objects from airborne laser scanner data and aerial images has been a topic of research for decades. Airborne laser scanner data are very efficient source for the detection of the buildings. Half of the world population lives in urban/suburban areas, so detailed, accurate and up-to-date building information is of great importance to every resident, government agencies, and private companies. The main objective of this paper is to extract the features for the detection of building using airborne laser scanner data and aerial images. To achieve this objective, a method of integration both LiDAR and aerial images has been explored: thus the advantages of both data sets are utilized to derive the buildings with high accuracy. Airborne laser scanner data contains accurate elevation information in high resolution which is very important feature to detect the elevated objects like buildings and the aerial image has spectral information and this spectral information is an appropriate feature to separate buildings from the trees. Planner region growing segmentation of LiDAR point cloud has been performed and normalized digital surface model (nDSM) is obtained by subtracting DTM from the DSM. Integration of the nDSM, aerial images and the segmented polygon features from the LiDAR point cloud has been carried out. The optimal features for the building detection have been extracted from the integration result. Mean height value of the nDSM, Normalized difference vegetation index (NDVI) and the standard deviation of the nDSM are the effective features. The accuracy assessment of the classification results obtained using the calculated attributes was done. Assessment result yielded an accuracy of almost 92 % explaining the features which are extracted by integrating the two data sets was large extent, effective for the automatic detection of the buildings.

Influence of ULS data acquisition characteristics on the achievable stem reconstruction accuracies

2020 ◽  
Author(s):  
Moritz Bruggisser ◽  
Johannes Otepka ◽  
Norbert Pfeifer ◽  
Markus Hollaus
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Stem Diameter ◽  
Forest Monitoring ◽  
Individual Tree ◽  
Detection Rates ◽  
Point Count ◽  
Tree Stem

&lt;p&gt;Unmanned aerial vehicles-borne laser scanning (ULS) allows time-efficient acquisition of high-resolution point clouds on regional extents at moderate costs. The quality of ULS-point clouds facilitates the 3D modelling of individual tree stems, what opens new possibilities in the context of forest monitoring and management. In our study, we developed and tested an algorithm which allows for i) the autonomous detection of potential stem locations within the point clouds, ii) the estimation of the diameter at breast height (DBH) and iii) the reconstruction of the tree stem. In our experiments on point clouds from both, a RIEGL miniVUX-1DL and a VUX-1UAV, respectively, we could detect 91.0 % and 77.6 % of the stems within our study area automatically. The DBH could be modelled with biases of 3.1 cm and 1.1 cm, respectively, from the two point cloud sets with respective detection rates of 80.6 % and 61.2 % of the trees present in the field inventory. The lowest 12 m of the tree stem could be reconstructed with absolute stem diameter differences below 5 cm and 2 cm, respectively, compared to stem diameters from a point cloud from terrestrial laser scanning. The accuracy of larger tree stems thereby was higher in general than the accuracy for smaller trees. Furthermore, we recognized a small influence only of the completeness with which a stem is covered with points, as long as half of the stem circumference was captured. Likewise, the absolute point count did not impact the accuracy, but, in contrast, was critical to the completeness with which a scene could be reconstructed. The precision of the laser scanner, on the other hand, was a key factor for the accuracy of the stem diameter estimation.&amp;#160;&lt;br&gt;The findings of this study are highly relevant for the flight planning and the sensor selection of future ULS acquisition missions in the context of forest inventories.&lt;/p&gt;

scholarly journals INDOOR MAPPING OF A COMPLEX CULTURAL HERITAGE SCENE USING TLS AND HMLS LASER SCANNING

2021 ◽  
Vol XLIII-B2-2021 ◽  
pp. 605-612
Author(s):  
V. E. Oniga ◽  
A. I. Breaban ◽  
E. I. Alexe ◽  
C. Văsii
Keyword(s):  
Standard Deviation ◽  
Cultural Heritage ◽  
Long Range ◽  
Interior Design ◽  
Point Cloud ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Point Clouds ◽  
Acquisition Time ◽  
Wide Range

Abstract. Indoor mapping and modelling is an important research subject with application in a wide range of domains including interior design, real estate, cultural heritage conservation and restoration. There are multiple sensors applicable for 3D indoor modelling, but the laser scanning technique is frequently used because of the acquisition time, detailed information and accuracy. In this paper, the efficiency of the Maptek I-Site 8820 terrestrial scanner, which is a long-range laser scanner and the accuracy of a HMLS point cloud acquired with a mobile scanner, namely GeoSlam Zeb Horizon were tested for indoor mapping. Aula Magna “Carmen Silva” of the “Gheorghe Asachi” Technical University of Iasi is studied in the current paper since the auditorium interior creates a distinct environment that combines complex geometric structures with architectural lighting and for preserving its great cultural value, the monument has a national historical significance. The registration process of the TLS point clouds was done using two methods: a semi-automatic one with artificial targets and a completely automatic one, based on Iterative Closest Point (ICP) algorithm. The resulted TLS point cloud was analysed in relation to the HMLS point cloud by computing the M3C2 (Multiscale Model to Model Cloud Comparison), obtaining a standard deviation of 2.1 cm and by investigating the Hausdorff distances from which resulted a standard deviation (σ) of 1.6 cm. Cross-sections have been extracted from the HMLS and TLS point clouds and after comparing the sections, 80% of the sigma values are less or equal to 1 cm. The results show high potential of using HMLS and also a long-range laser scanner for 3D modelling of complex scenes, the occlusion effect in the case of TLS being only 5% of the scanned area.

Sign in / Sign up

Export Citation Format

Share Document