SINGLE CYLINDER ENGINE STUDIES WITH IMPINGING DIRECT INJECTION FUEL INJECTOR

2017 ◽  
Author(s):  
Ankur Gupta
Keyword(s):  
Direct Injection ◽  
Fuel Injector ◽  
Single Cylinder ◽  
Single Cylinder Engine

Performance Evaluation of Low Heat Rejection Engines

1994 ◽  
Vol 116 (4) ◽  
pp. 758-764 ◽  
Author(s):  
X. Sun ◽  
W. G. Wang ◽  
R. M. Bata ◽  
X. Gao
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Engine Performance ◽  
Injection System ◽  
Fuel Injection System ◽  
Heat Rejection ◽  
Single Cylinder ◽  
Single Cylinder Engine ◽  
Low Heat Rejection Engine

Improving the performance of the Chinese B135 six-cylinder direct injection turbocharged and turbocompounded Low Heat Rejection Engine (LHRE) was based on experimental and analytical studies. The studies were primarily applied on a B1135 single-cylinder LHR engine and a conventional water-cooled B1135 single cylinder engine. Performance of the B1135 LHRE was worse than that of the conventional B1135 due to a deterioration in the combustion process of the B1135 LHRE. The combustion process was improved and the fuel injection system was redesigned and applied to the B135 six-cylinder LHRE. The new design improved the performance of the LHRE and better fuel economy was realized by the thermal energy recovered from the exhaust gases by the turbocompounding system.

scholarly journals Experimental investigation on n-butanol/methyl oleate dual fuel RCCI combustion in a single cylinder engine at high-load condition

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Xin Wang ◽  
Qian Zhang ◽  
Fangjie Liu ◽  
Yifan Jin ◽  
Xin Li
Keyword(s):  
Methyl Oleate ◽  
Direct Injection ◽  
Dual Fuel ◽  
Pilot Injection ◽  
Cylinder Pressure ◽  
Engine Load ◽  
Single Cylinder ◽  
Single Cylinder Engine ◽  
Test Conditions ◽  
Hc Emissions

AbstractReactivity controlled compression ignition (RCCI) engines have a high thermal efficiency as well as low emissions of soot and nitrogen oxides (NOx). However, there is a conflict between combustion stability and harmful emissions at high engine load. Therefore, this work presented a novel approach for regulating n-butanol/methyl oleate dual fuel RCCI at high engine load in attaining lower pollutant emissions while maintaining stable combustion and avoiding excessive in-cylinder pressure. The tests were conducted on a single cylinder engine under rated speed and 90% full load. In this study, n-butanol was selected as a low-reactivity fuel for port injection, and n-butanol/methyl oleate blended fuel was used for in-cylinder direct injection. Combustion and emission characteristics of the engine were first investigated with varied ratios of n-butanol port injection (PFI) and direct injection (DI). Results showed that as the ratio of n-butanol PFI and DI rose, the peak cylinder pressure and heat release rate increased, while NOx and soot emissions reduced, and carbon monoxide (CO) and hydrocarbon (HC) emissions increased under most test conditions. When RNBPI = 40% and RNBDI = 20%, the soot and NOx emissions of the engine were near the lowest values of all test conditions, yet the peak in-cylinder pressure and fuel consumption could not increase significantly. Therefore, the possibility of optimizing the combustion process and lowering emissions by adjusting the pilot injection strategy was investigated utilizing these fuel injection ratios. The results revealed that with an appropriate pilot injection ratio and interval, the peak in-cylinder pressure and NOx emission were definitely reduced, while soot, CO, and HC emissions did not significantly increase.

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

A Transient Single Cylinder Test System for Engine Research and Control Development

2005 ◽  
Author(s):  
John L. Lahti ◽  
Matthew W. Snyder ◽  
John J. Moskwa
Keyword(s):  
Test System ◽  
Intake Manifold ◽  
Test Accuracy ◽  
Test Configuration ◽  
Single Cylinder ◽  
Cylinder Test ◽  
Single Cylinder Engine ◽  
Wide Range ◽  
Reduce Development Time ◽  
High Bandwidth

A transient test system was developed for a single cylinder research engine that greatly improves test accuracy by allowing the single cylinder to operate as though it were part of a multi-cylinder engine. The system contains two unique test components: a high bandwidth transient hydrostatic dynamometer, and an intake airflow simulator. The high bandwidth dynamometer is used to produce a speed trajectory for the single cylinder engine that is equivalent to that produced by a multi-cylinder engine. The dynamometer has high torque capacity and low inertia allowing it to simulate the speed ripple of a multi-cylinder engine while the single cylinder engine is firing. Hardware in loop models of the drivetrain and other components can be used to test the engine as though it were part of a complete vehicle, allowing standardized emissions tests to be run. The intake airflow simulator is a specialized intake manifold that uses solenoid air valves and a vacuum pump to draw air from the manifold plenum in a manner that simulates flow to other engine cylinders, which are not present in the single cylinder test configuration. By regulating this flow from the intake manifold, the pressure in the manifold and the flow through the induction system are nearly identical to that of the multi-cylinder application. The intake airflow simulator allows the intake runner wave dynamics to be more representative of the intended multi-cylinder application because the appropriate pressure trajectory is maintained in the intake manifold plenum throughout the engine cycle. The system is ideally suited for engine control development because an actual engine cylinder is used along with a test system capable of generating a wide range of transient test conditions. The ability to perform transient tests with a single cylinder engine may open up new areas of research exploring combustion and flow under transient conditions. The system can also be used for testing the engine under conditions such as cylinder deactivation, fuel cut-off, and engine restart. The improved rotational dynamics and improved intake manifold dynamics of the test system allow the single cylinder engine to be used for control development and emissions testing early in the engine development process. This can reduce development time and cost because it allows hardware problems to be identified before building more expensive multi-cylinder engines.

Sign in / Sign up

Export Citation Format

Share Document