The Effect of Compression Ratio on Performance of Generator Set Fuelled with Raw Biogas

In order to utilize a raw biogas as a fuel of generator set (gen-set), it is important to figure out optimum operating parameter of the gen-set, i.e. compression ratio. The present work aims to investigate the effect of compression ratio on performance of 3 kW gen-set fuelled with raw biogas and to obtain optimum compression ratio for operation of the gen-set on raw biogas. The gen-set used in the present work is bi-fuel engine, i.e. fuelled with gasoline or LPG. The performance of the engine fuelled with raw biogas in terms of brake power, brake torque, brake specific fuel consumption, and thermal efficiency is evaluated at compression ratio of 7.5, 8.5, 9.5, and 10.5. The work is carried out under electrical load of 240, 420, and 600 Watt. The result indicates that compression ratio affects the rotational speed, brake power, brake torque, brake specific fuel consumption, and thermal efficiency of the gen-set. Optimum compression ratio for the gen-set fuelled with raw biogas is 9.5. At the optimum compression ratio, maximum brake power, brake torque, and thermal efficiency of are 450.37 W, 1.66 Nm, and 46.93%, respectively. Minimum brake specific fuel is 0.59 kg/kWh at the optimum compression ratio.

The experimental investigation of diesel fuel-biofuel blends at different injection pressures in a DI diesel engine

In this study, it was aimed to investigate the effects of a diesel-biodiesel blend (B20) and a diesel-biodiesel-bioethanol blend (BE5) on combustion parameters in addition to engine performance and exhaust emissions compared with diesel fuel. Parameters included in the evaluation was brake specific fuel consumption, brake thermal efficiency, CO, CO2, HC, NOx, smoke opacity emissions and finally cylinder pressure, heat release rate, ignition delay, some key points of the combustion phases such as start of ignition, start of combustion, CA50 and CA90 and combustion duration. Engine tests were conducted at different injection pressures of 170 bar, 190 bar, which is the original injection pressure, and 220 bar by the engine being loaded by 25, 50, 75 and 100% for the assessment of engine performance and exhaust emissions. For combustion evaluation, the data obtained at 1400 rpm, maximum torque-speed, and 2800 rpm, maximum power-speed were used, while the injection pressures were set to 170, 190 and 220 bar under full load condition. According to test results, the better performance characteristics, exhaust emissions and combustion behaviour of engine were obtained with the use of BE5 at high injection pressure. So, BE5 fuel improved brake specific fuel consumption by about 7% and brake thermal efficiency by about 6% compared to B20. In addition, while the emission values of BE5 gave better results than diesel fuel, it reduced the NOx and smoke emissions of B20 by approximately 1.4% and 6.4% respectively. Moreover, it has achieved a reduction in smoke emission of up to 45% compared to diesel fuel.

Biodiesel Extraction from Chicken Fat and Its Effect on the Performance and Emission Characteristics of the Diesel Engine

This study focuses on the conversion of chicken fat into chicken fat methyl ester (CFME) and its use in the diesel engine. Baseline fuel i.e., diesel and chicken fat biodiesel are the fuels tested to study their effect on the performance and emission characteristics of diesel engines. To enhance the performance and emission characteristics, ethanol up to 20% is added as an additive to the chicken fat biodiesel. The physiochemical properties revealed that the fuel blends properties are closer to the diesel fuel. The experimental investigations revealed that additive blended biodiesel enhanced the performance by reducing the brake-specific fuel consumption and increasing the brake thermal efficiency. Moreover, the emissions are considerably reduced by the additive blended chicken fat biodiesel. Therefore, chicken fat biodiesel can be considered as a substitute fuel to be used in the diesel engine without any modifications.

Effects of Different Biodiesel-Diesel Blend Fuel on Combustion and Emission Characteristics of a Diesel Engine

In this paper, biodiesel was used as an alternative fuel to investigate the combustion and emission characteristics of a four-stroke diesel engine, in terms of cylinder pressure, heat release rate, cylinder temperature, brake thermal efficiency, brake specific fuel consumption, nitrogen oxide, soot, carbon monoxide, and hydrocarbon. Firstly, a diesel engine cylinder model was developed by AVL-Fire software coupled with CHEMKIN code to simulate the injection and combustion of biodiesel with a kinetic mechanism with 106 species and 263 reactions. Then, the simulation model was validated by experimental results under 100% and 50% load conditions and used to simulate the combustion process of a diesel engine fueled with pure diesel, biodiesel, and biodiesel–diesel blends with 10%, 20%, 30% biodiesel by volume, respectively. The results showed that the brake specific fuel consumption increased with the increase of mixed biodiesel ratio. The brake specific fuel consumptions of B10, B20 and B30 increased by 1.1%, 2.3% and 3.3%, respectively, compared with that of D100. The combustion and emission characteristics of the diesel engine are improved. Therefore, biodiesel can be used as an alternative fuel for the diesel engine. The diesel–biodiesel fuel can improve the combustion and emission characteristics of the diesel engine.

Comparison between PEE10 and PEE10-Bioethanol Blends on Performance and Emission Characteristics of a HSDI Diesel Engine

Biofuels are an alternative fuel currently being developed to reduce the diesel-engine environmental impact. The release of carbon dioxide (CO2), nitric oxide (NO) and black smoke (BS) becomes an issue derived from diesel engines even in lean-mixture combustion causing an adverse effect to human health. The main aim of the research study is to present the use of biofuels, a mixture of diesel and 10 % palm oil ethyl ester (PEE10) and PEE10 blended with bioethanol from 5 to 20 %, compared with conventional diesel fuel. The biofuels were run on a high-speed direct injection diesel engine at a constant speed of 3,000 rpm under various loads. The use of PEE10 resulted in brake thermal efficiency (BTE) reduction by 2 % and brake specific fuel consumption (BSFC) incrementation by 8 %, but the exhaust emissions were lower than diesel, except for CO2 and NO. However, PEE10 engine performance was better and exhaust gas emissions were lower for both pollutants than diesel mixed with 10 % bioethanol. The investigation of PEE10 with increasing bioethanol revealed that the use of PEE10 blended with 5 % bioethanol (PEE10E5) can improve engine performance, while the BTE and BSFC were close to that of diesel, and exhaust emissions, especially CO2, NO and BS reduced. Moreover, BTE from PEE10E5 fueling increased by 2 % but BSFC was subtle increased, compared to PEE10. On the other hand, the increasing bioethanol from 10 to 20 % in PEE10 led to the more reduction in engine performance, but the engine pollutants were also continuously decreased. Specifically, the blend of PEE10 and 20 % bioethanol indicates that CO2, NO and BS were reduced by 10, 15 and 33 %, respectively, compared to diesel fuel. HIGHLIGHTS A mixture of diesel and 10 % palm oil ethyl ester (PEE10) has less exhaust emissions than diesel blended with 10 % palm oil methyl ester (PME10) PEE10 blended with 5 % bioethanol can improve engine performance, while the brake thermal efficiency and brake specific fuel consumption are close to that of diesel and PME10 The increasing bioethanol from 10 to 20 % in PEE10 leads to the more reduction in engine performance, but the engine pollutants, especially carbon dioxide, nitric oxide and black smoke, are also continuously decreased GRAPHICAL ABSTRACT

Metal Oxides as Soluble Nano Catalyst on Biodiesel: A Review

Nano particles of metal oxide developed as soluble nano additive in liquid fuels to improve fuel quality. One application of nano metal oxide particles is an additive to biodiesel. Biodiesel is an alternative fuel that can reduce dependence on fossil fuels. Pure biodiesel has a relatively lower calorific value compared to fossil fuels. Low calorific value results in increased brake specific fuel consumption. Moreover, biodiesel has a higher density and viscosity compared to fossil fuel. The content of carbon monoxide (CO), unburned hydrocarbons (HC) and nitrogen oxide (NOx) in exhaust gases with biodiesel is higher than fossil fuels. Metal oxide nanoparticles are added to biodiesel between 6 to 80 nm with concentrations about 50 to 500 ppm. Addition of metal oxide nanoparticles to biodiesel can improve brake thermal efficiency, reduce brake specific fuel consumption, carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxide (NOx) and improve carbon dioxide (CO2) emission due to the catalytic effect of metal oxide nanoparticles. Metal oxide acts as an oxidation catalyst thereby reduce the carbon combustion activation temperature and thus enhances hydrocarbon oxidation, promoting complete combustion. Nanoparticles that are often used in various studies are nickel (II) oxide (NiO), cerium (IV) oxide (CeO2), titanium oxide (TiO2), zinc oxide (ZnO), aluminum oxide (Al2O3), and silicon dioxide (SiO2). This review paper describes the progress and development of nano metal oxide applications as additives for biodiesel, and the discussion in this paper is divided into 3 main topics, including the effects of nanoparticles on the properties of biodiesel, engine performance, and emission characteristics.

An Assessment on Performance Characteristics of Diesel Engine Using Lemongrass-Diesel Oil Fuel Blends

Indeed, the development of alternative fuels for use in internal combustion engines has become an essential requirement to meet the energy demand and to deal with the different problems related to fuel. The research in this domain leads to the identification of adverse fuel properties and for their solution standard limits are being defined. This paper outlines an investigation of performance and combustion characteristics of a 4-stroke diesel engine using different cymbopogon (lemongrass) - diesel fuel blends. 10% to 40% cymbopogon is mixed with diesel fuel and tested for performance characteristics like brake specific fuel consumption and brake thermal efficiency. To obtain emission characteristics smoke density in the terms of HSU has been measured. In result, it has observed that there is an increase of 5% in brake thermal efficiency and 16.33% decrease in brake specific fuel consumption. Regarding emission characteristics, a 12.9% decrease in smoke emission has been found.

Effects of Different Mixture Ratios of Methanol-Diesel on the Performance Enhancement and Emission Reduction for a Diesel Engine

To improve the combustion and emission characteristics of diesel engines, methanol-diesel fuels with different mixing ratios (DM0, DM10, DM20, DM30, and DM40) were used to investigate the effects of methanol addition on the combustion and emission of a four-stroke diesel engine in terms of cylinder pressure, brake power, brake-specific fuel consumption, and nitrogen oxides, soot, and carbon monoxide emissions. Firstly, an improved entire diesel engine model was developed using AVL-BOOST software and validated by the experimental results. The results showed that the increase of methanol content in the fuel mixture had a negative impact on the performance characteristic of the diesel engine, but significantly improved the emission characteristic of the diesel engine. With the methanol ratio in the mixed fuel increased to 10%, 20%, 30%, and 40%, the cylinder pressure of the engine increased by 0.89%, 1.48%, 2.29%, and 3.17%, respectively. However, the power decreased by 3.76%, 6.74%, 11.35%, and 15.45%, the torque decreased by 3.76%, 6.74%, 11.35%, and 15.45%, respectively, and the brake specific fuel consumption increased by 3.77%, 6.92%, 12.33%, and 17.61%, respectively. In addition, with the methanol ratio in the mixed fuel increased to 10%, 20%, 30%, and 40%, the carbon monoxide emission decreased by 21.32%, 39.04%, 49.81%, and 56.59% and the soot emission decreased by 0.25%, 8.69%, 16.81%, and 25.28%, respectively. Therefore, the addition of methanol to the fuel can improve the combustion and emission characteristics of the engine.

EXPERIMENTAL ANALYSIS OF THE COMBUSTION CHAMBER COATED WITH Mo AND Al2O3-TiO2 IN A DIESEL ENGINE

The effect of thermal-barrier coatings (TBCs) reduces fuel consumption, effectively improving the engine efficiency. This research focused on a TBC with a thickness of 300 µm insulating the combustion chamber of a direct ignition (DI) engine. The piston crown, inlet and exhaust-valve head were coated using air-plasma-spray coating. Ceramic powder materials such as molybdenum (Mo) and aluminum oxide titanium dioxide (Al2O3-TiO2) were used. A performance test of the engine with the coated combustion chamber was carried out to investigate the brake power, brake thermal efficiency, volumetric efficiency, brake specific fuel consumption and air-fuel ratio. Also, an emission-characteristic test was carried out to investigate the emissions of unburned hydrocarbon (HC), carbon monoxide (CO), nitrogen oxides (NO, NO2, NO3) and smoke opacity (SO). The results reveal that the brake thermal efficiency and brake specific fuel consumption show significant increases because of these coating materials. The effect of the Al2O3-TiO2 coating significantly reduces the HC and CO engine emissions.

Effects of Different Diesel-Ethanol Dual Fuel Ratio on Performance and Emission Characteristics of Diesel Engine

In this paper, a four-stroke engine diesel was employed to investigate the effects of different fuel mixture ratios of diesel and ethanol on engine performance and emission characteristics in terms of cylinder temperature, heat release rate, brake power, brake thermal efficiency, brake specific fuel consumption, and cylinder pressure. The corresponding simulation model of diesel engine was developed by AVL-Fire coupled CHEMKIN code, and an improved chemical kinetics mechanism containing 34 reactions and 19 species was employed to simulate the fuel spray process and combustion process. The simulation model was validated by experimental results under 100% and 50% load conditions and used to simulate the combustion process of diesel engine fueled with pure diesel and diesel–ethanol blends with 10%, 20%, and 30% ethanol by volume, respectively. The results showed that the increase of ethanol content in the blended fuel had a certain negative impact on the performance characteristic of diesel engine and significantly improved the emission characteristic of the engine. With the ethanol proportion in the blended fuel increased to 10%, 20%, and 30%, the brake thermal efficiency of the engine increased by 2.24%, 4.33%, and 6.37% respectively. However, the brake-specific fuel consumption increased by 1.56%, 3.49%, and 5.74% and the power decreased by 1.58%, 3.46%, and 5.54% respectively. In addition, with the ethanol proportion in the blended fuel increased to 10%, 20%, and 30%, the carbon monoxide emission decreased by 34.69%, 47.60%, and 56.58%, and the soot emission decreased by 7.83%, 15.24%, and 22.52% respectively. Finally, based on the combining fuzzy and grey correlation theory, nitrogen oxide emission has the highest correlation with engine power and brake-specific fuel consumption. The values reach 0.9103 and 0.8945 respectively. It shows that nitrogen oxide emission and cylinder pressure have a significant relationship on engine power and brake-specific fuel consumption.