scholarly journals Influence of the preparation method on the photocatalytic activity of Nd-modified TiO2

2018 ◽  
Vol 9 ◽  
pp. 447-459 ◽  
Author(s):  
Patrycja Parnicka ◽  
Paweł Mazierski ◽  
Tomasz Grzyb ◽  
Wojciech Lisowski ◽  
Ewa Kowalska ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Surface Defects ◽  
Diffuse Reflectance Spectroscopy ◽  
Bet Surface Area ◽  
Luminescence Spectroscopy ◽  
X Ray ◽  
Gaseous Toluene

Nd-modified TiO2 photocatalysts have been obtained via hydrothermal (HT) and sol–hydrothermal (SHT) methods. The as-prepared samples were characterized by X-ray diffraction (XRD), BET surface area measurements, scanning electron microscopy (SEM), diffuse reflectance spectroscopy (DRS), luminescence spectroscopy and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity of the synthesized samples was evaluated by the degradation of phenol in aqueous solution under irradiation with UV–vis (λ > 350 nm) and vis (λ > 420 nm) light, as well as by the degradation of gaseous toluene under irradiation with vis (λmax = 415 nm) light. It was found that Nd-modified TiO2 is an efficient photocatalyst for the degradation of phenol and toluene under visible light. XPS analysis revealed that the photocatalyst prepared via HT method contains a three-times higher amount of hydroxy groups at the surface layer and a two-times higher amount of surface defects than that obtained by the SHT method. The photocatalytic efficiency of phenol and toluene degradation under vis irradiation in the presence of 0.25% Nd-TiO2(HT) reached 0.62 and 3.36 μmol·dm−1·min−1, respectively. Photocatalytic activity tests in the presence of Nd-TiO2 and scavenger confirm that superoxide radicals were responsible for the visible light-induced degradation of the model pollutant in aqueous solution.

scholarly journals Enhanced Visible-Light-Driven Photocatalytic Activity of ZnAl Layered Double Hydroxide by Incorporation of Co2+

2018 ◽  
Vol 13 (3) ◽  
pp. 502 ◽  
Author(s):  
Deyang Li ◽  
Lihui Fan ◽  
Min Qi ◽  
Yanming Shen ◽  
Dongbin Liu ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Layered Double Hydroxide ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Degradation Mechanism ◽  
Bet Surface Area ◽  
X Ray ◽  
Visible Light Driven ◽  
Double Hydroxide

Co-doped ZnAl layered double hydroxides (LDH) were papered by coprecipitation. The prepared samples were characterized by multiple techniques including X-ray Diffraction (XRD), Brunauer−Emmett−Teller (BET) surface area, Scanning Electronic Microscopy (SEM), Transmission Electron Microscopy (TEM), X-ray Photoelectron Spectroscopy (XPS) and UV−Vis Diffuse-Reflectance Spectroscopy (UV−Vis DRS). The incorporation of Co2+ into the ZnAl LDH sheets as CrO6 octahedron forms a new  energy level which contributes for the excitation of electrons under visible light. The doped Co2+ at a reasonable content also serves as photo-generated charges separator and improves the visible light photocatalytic activity of ZnAl LDH. A degradation mechanism based on the hydroxyl radical as the active species was proposed. Copyright © 2018 BCREC Group. All rights reservedReceived: 3rd February 2018; Revised: 8th July 2018; Accepted: 13rd July 2018How to Cite: Li, D., Fan, L., Qi, M., Shen, Y., Liu, D., Li, S. (2018). Enhanced Visible-Light-Driven Photocatalytic Activity of ZnAl Layered Double Hydroxide by Incorporation of Co2+. Bulletin of Chemical Reaction Engineering & Catalysis, 13 (3): 502-511 (doi:10.9767/bcrec.13.3.2168.502-511)Permalink/DOI: https://doi.org/10.9767/bcrec.13.3.2168.502-511 

scholarly journals Photocatalytic Degradation of Estriol Using Iron-Doped TiO2 under High and Low UV-Irradiation

2018 ◽  
Author(s):  
Irwing M. Ramírez-Sánchez ◽  
Erick R. Bandala
Keyword(s):  
Photocatalytic Activity ◽  
Electron Microscope ◽  
Uv Irradiation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Bet Surface Area ◽  
Doped Tio2 ◽  
X Ray ◽  
Transmission Electron ◽  
Iron Doped

Iron Doped TiO2 nanoparticles (Fe-TiO2) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO2 physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe3+) was in the lattice of TiO2 and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe3+ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO2 materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO2) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO2 (zero-iron TiO2) and Aeroxide® TiO2 P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO2 under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

scholarly journals Preparation and Characterization of Defective TiO2. The Effect of the Reaction Environment on Titanium Vacancies Formation

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2763
Author(s):  
Zuzanna Bielan ◽  
Szymon Dudziak ◽  
Agnieszka Sulowska ◽  
Daniel Pelczarski ◽  
Jacek Ryl ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Hydrothermal Reaction ◽  
High Photocatalytic Activity ◽  
Paramagnetic Resonance ◽  
X Ray ◽  
Light Activity ◽  
Cheap Alternative

Among various methods of improving visible light activity of titanium(IV) oxide, the formation of defects and vacancies (both oxygen and titanium) in the crystal structure of TiO2 is an easy and relatively cheap alternative to improve the photocatalytic activity. In the presented work, visible light active defective TiO2 was obtained by the hydrothermal reaction in the presence of three different oxidizing agents: HIO3, H2O2, and HNO3. Further study on the effect of used oxidant and calcination temperature on the physicochemical and photocatalytic properties of defective TiO2 was performed. Obtained nanostructures were characterized by X-ray diffractometry (XRD), specific surface area (BET) measurements, UV-Vis diffuse reflectance spectroscopy (DR-UV/Vis), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS), and electron paramagnetic resonance (EPR) spectroscopy. Degradation of phenol as a model pollutant was measured in the range of UV-Vis and Vis irradiation, demonstrating a significant increase of photocatalytic activity of defective TiO2 samples above 420 nm, comparing to non-defected TiO2. Correlation of EPR, UV-Vis, PL, and photodegradation results revealed that the optimum concentration of HIO3 to achieve high photocatalytic activity was in the range of 20–50 mol%. Above that dosage, titanium vacancies amount is too high, and the obtained materials’ photoactivity was significantly decreased. Studies on the photocatalytic mechanism using defective TiO2 have also shown that •O2− radical is mainly responsible for pollutant degradation.

scholarly journals Synthesis of C-N-S-Tridoped TiO2 from Vietnam Ilmenite Ore and Its Visible Light-Driven-Photocatalytic Activity for Tetracyline Degradation

2020 ◽  
Vol 2020 ◽  
pp. 1-14 ◽  
Author(s):  
Nguyen Thi Lan ◽  
Vo Hoang Anh ◽  
Hoang Duc An ◽  
Nguyen Phi Hung ◽  
Dao Ngoc Nhiem ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Nitrogen Adsorption ◽  
Photocatalytic Decomposition ◽  
Raman Scattering Spectroscopy ◽  
X Ray ◽  
Visible Light Driven

In this study, C-N-S-tridoped TiO2 composite was fabricated from TiO2 prepared from ilmenite ore and thiourea by means of hydrothermal method. The obtained material was characterized by X-ray diffraction, Raman scattering spectroscopy, UV-Vis diffuse reflectance spectroscopy, nitrogen adsorption-desorption isotherms, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). It was found that C-N-S-tridoped TiO2 material has a large specific surface area, showing good photocatalytic activity on the degradation of antibiotic tetracycline in visible light region. The study on the mechanism of tetracycline photodegradation using the liquid chromatography with mass spectrometry was performed. It was found that tetracycline has been degraded over C-N-S-tridoped TiO2 catalyst into many different intermediates which can eventually be converted into CO2 and H2O. The kinetics of photocatalytic decomposition of tetracycline were investigated. In addition, the obtained material could catalyze well the degradation of other antibiotics (ciprofloxacin and chloramphenicol) and dyes (rhodamine-B, methylene blue, and organe red). The catalyst was stable after five recycles with slight loss of catalytic activity, which indicates great potential for practical application of C-N-S-tridoped TiO2 catalyst in treatment of wastewater containing tetracycline in particular or antibiotics in general.

scholarly journals Improved Visible Light Photocatalytic Activity for TiO2Nanomaterials by Codoping with Zinc and Sulfur

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Qianzhi Xu ◽  
Xiuying Wang ◽  
Xiaoli Dong ◽  
Chun Ma ◽  
Xiufang Zhang ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sunlight Irradiation ◽  
X Ray ◽  
Transmission Electron ◽  
Photoinduced Charge

S/Zn codoped TiO2nanomaterials were synthesized by a sol-gel method. X-ray diffraction, UV-vis diffuse reflectance spectroscopy, transmission electron microscopy, photoluminescence spectroscopy, and X-ray photoelectron spectroscopy were used to characterize the morphology, structure, and optical properties of the prepared samples. The introduction of Zn and S resulted in significant red shift of absorption edge for TiO2-based nanomaterials. The photocatalytic activity was evaluated by degrading reactive brilliant red X-3B solution under simulated sunlight irradiation. The results showed S/Zn codoped TiO2exhibited higher photocatalytic activity than pure TiO2and commercial P25, due to the photosynergistic effect of obvious visible light absorption, efficient separation of photoinduced charge carriers, and large surface area. Moreover, the content of Zn and S in the composites played important roles in photocatalytic activity of TiO2-based nanomaterials.

Preparation of BiXY(2-X)O3 and its Photocatalytic Degradation of Molasses Fermentation Wastewater under Visible-Light Irradiation

2011 ◽  
Vol 287-290 ◽  
pp. 1640-1645 ◽  
Author(s):  
Min Guang Fan ◽  
Zu Zeng Qin ◽  
Zi Li Liu ◽  
Tong Ming Su
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance ◽  
Diffuse Reflectance Spectroscopy ◽  
Active Oxygen Species ◽  
Light Irradiation ◽  
X Ray

A series of BixY(2-x)O3photocatalysts were successfully prepared by a solid-state reaction and were subsequently characterized by powder X-ray diffraction, UV-vis diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy (XPS). The UV-vis diffuse reflectance spectra revealed that the BixY(2-x)O3samples absorbed light in the visible-light range (400-800 nm). The XPS results indicated that active oxygen species were generated on the Bi1.8Y0.2O3surface, which displayed a higher photocatalytic activity. When using photocatalytic degradation molasses fermentation wastewater as a model reaction, the Bi1.8Y0.2O3showed higher photocatalytic activity in comparison to Bi0.2Y1.8O3under visible-light irradiation.

scholarly journals Fabrication of Bi-DopedTiO2Spheres with Ultrasonic Spray Pyrolysis and Investigation of Their Visible-Light Photocatalytic Properties

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Jianhui Huang ◽  
Wahkit Cheuk ◽  
Yifan Wu ◽  
Frank S. C. Lee ◽  
Wingkei Ho
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Spray Pyrolysis ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Ultrasonic Spray Pyrolysis ◽  
X Ray ◽  
Ultrasonic Spray ◽  
Doped Titania

Bismuth-doped TiO2submicrospheres were synthesized by ultrasonic spray pyrolysis. The prepared bismuth-doped titania was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-visible diffuse reflectance spectroscopy (UV-vis DRS), and X-ray photoelectron spectroscopy (XPS). Aqueous photocatalytic activity was evaluated by the decomposition of methyl orange under visible-light irradiation. The results indicate that doping of bismuth remarkably affects the phase composition, crystal structure, and the photocatalytic activity. The sample with 2% Bi exhibits the optimum photocatalytic activity.

scholarly journals Fabrication of Mo+N-Codoped TiO2Nanotube Arrays by Anodization and Sputtering for Visible Light-Induced Photoelectrochemical and Photocatalytic Properties

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Min Zhang ◽  
Dandan Lu ◽  
Guotian Yan ◽  
Juan Wu ◽  
Jianjun Yang
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Photocurrent Density ◽  
Electrochemical Anodization ◽  
Nanotube Arrays ◽  
Step Method ◽  
X Ray ◽  
New States

Mo,N-codoped TiO2nanotube arrays (TNAs) were fabricated by a two-step method consisting of electrochemical anodization and subsequent magnetron sputtering of Mo. The samples were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). The results showed that the Mo,N-codoped TiO2nanotube arrays exhibited higher visible light absorbance and remarkably enhanced photocurrent density and photocatalytic activity compared with single N-doped TiO2. The highly efficient photoelectrochemical and photocatalytic activity is associated with the codoping effect between Mo and N, which plays a key role in producing new states, narrowing the bandgap, and reducing the recombination thereby effectively improving the visible light absorption and photocatalytic activity of TNAs.

scholarly journals Neodymium-DopedTiO2with Anatase and Brookite Two Phases: Mechanism for Photocatalytic Activity Enhancement under Visible Light and the Role of Electron

2012 ◽  
Vol 2012 ◽  
pp. 1-10 ◽  
Author(s):  
Douga Nassoko ◽  
Yan-Fang Li ◽  
Jia-Lin Li ◽  
Xi Li ◽  
Ying Yu
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Organic Pollutant ◽  
Sol Gel ◽  
Reactive Species ◽  
X Ray ◽  
Photogenerated Electrons

Titanium dioxide (TiO2) doped with neodymium (Nd), one rare earth element, has been synthesized by a sol-gel method for the photocatalytic degradation of rhodamine-B under visible light. The prepared samples are characterized by X-ray diffractometer, Raman spectroscopy, UV-Vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, and Brunauer-Emmett-Teller measurement. The results indicate that the prepared samples have anatase and brookite phases. Additionally, Nd as Nd3+may enter into the lattice ofTiO2and the presence of Nd3+substantially enhances the photocatalytic activity ofTiO2under visible light. In order to further explore the mechanism of photocatalytic degradation of organic pollutant, photoluminescence spectrometer and scavenger addition method have been employed. It is found that hydroxide radicals produced by Nd-dopedTiO2under visible light are one of reactive species for Rh-B degradation and photogenerated electrons are mainly responsible for the formation of the reactive species.

Improved visible-light photocatalytic activity of sodium tantalum oxide via biomass-derived silk fibroin doping

2018 ◽  
Vol 89 (7) ◽  
pp. 1332-1339
Author(s):  
Yehua Sun ◽  
Yuzhuo Luo ◽  
Yaofeng Zhu ◽  
Yaqin Fu
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Silk Fibroin ◽  
Photoelectron Spectroscopy ◽  
Structural Changes ◽  
Diffuse Reflectance Spectroscopy ◽  
Hydrothermal Process ◽  
X Ray ◽  
Transmission Electron

Biomass-derived silk fibroin (SF)-doped NaTaO3 catalysts were successfully synthesized by a simple hydrothermal process using SF as the dopant. The as-prepared samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS) analyses. The samples were tested as photocatalysts in the degradation of methylene blue under UV and visible light. XRD results showed the monoclinic structure of NaTaO3 lacking significant structural changes after anion doping. SEM and TEM images revealed the nanocubic morphology of the samples, the crystal particle sizes of which were about 100–300 nm. The XPS spectrum showed the peak of Ta4p3&N1s, indicating the combination of N and Ta. The UV-vis DRS results of the samples revealed a cut-off edge that red shifted from 315 nm of the pure NaTaO3 to 324 nm of the SF-doped counterpart. SF doping helped narrow the band gap and rendered the prepared sample sensitive to visible light. Under UV and visible-light irradiation, SF-doped NaTaO3 exhibited higher photocatalytic activity than that the undoped compound. SF-doped NaTaO3 samples also exhibited excellent stability during the recycling photocatalytic process.

Sign in / Sign up

Export Citation Format

Share Document