Swetha–a new, medium-duration variety with multiple tolerance released in Kerala, India

2009 ◽  
Vol 31 (2) ◽  
Author(s):  
T Ram ◽  
S Leena Kumari ◽  
ND Majumder ◽  
G Zachariah ◽  
RM Francis ◽  
...  
Keyword(s):  
1998 ◽  
Vol 88 (2) ◽  
pp. 137-143 ◽  
Author(s):  
Robert W. Sandrock ◽  
Hans D. VanEtten

α-Tomatine, synthesized by Lycopersicon and some Solanum species, is toxic to a broad range of fungi, presumably because it binds to 3β-hydroxy sterols in fungal membranes. Several fungal pathogens of tomato have previously been shown to be tolerant of this glycoalkaloid and to possess enzymes thought to be involved in its detoxification. In the current study, 23 fungal strains were examined for their ability to degrade α-tomatine and for their sensitivity to this compound and two breakdown products, β2-tomatine and tomatidine. Both saprophytes and all five non-pathogens of tomato tested were sensitive, while all but two tomato pathogens (Stemphylium solani and Verticillium dahliae) were tolerant of α-to-matine (50% effective dose > 300 μM). Except for an isolate of Botrytis cinerea isolated from grape, no degradation products were detected when saprophytes and nonpathogens were grown in the presence of α-tomatine. All tomato pathogens except Phytophthora infestans and Pythium aphani-dermatum degraded α-tomatine. There was a strong correlation between tolerance to α-tomatine, the ability to degrade this compound, and pathogenicity on tomato. However, while β2-tomatine and tomatidine were less toxic to most tomato pathogens, these breakdown products were inhibitory to some of the saprophytes and nonpathogens of tomato, suggesting that tomato pathogens may have multiple tolerance mechanisms to α-tomatine.


1979 ◽  
Vol 69 (7) ◽  
pp. 699 ◽  
Author(s):  
G. A. Chastagner
Keyword(s):  

Weed Science ◽  
2015 ◽  
Vol 63 (1) ◽  
pp. 235-241 ◽  
Author(s):  
Sarah T. Berger ◽  
Michael D. Netherland ◽  
Gregory E. MacDonald

Invasive watermilfoils, specifically Eurasian watermilfoil and the interspecific hybrid of Eurasian watermilfoil × northern watermilfoil, continue to be problematic for water resource managers. Herbicides are often used to control these nuisance weeds and have been historically successful in controlling Eurasian watermilfoil. A population of hybrid watermilfoil from Townline Lake in Michigan has shown increased tolerance to the herbicide fluridone. The objective of this work is to determine if cross- and multiple tolerance have also developed in this population. Eurasian watermilfoil plants collected from multiple sites and plants from Townline Lake were treated with 0, 5, 10, 20, 40, or 80 µg L−1of fluridone, norflurazon, or topramezone. Fluridone and norflurazon inhibit phytoene desaturase, whereas topramezone is a 4-hydroxyphenylpyruvate dioxygenase-inhibiting herbicide. Chlorophyll fluorescence (Fv/Fm) and pigment content was measured at 10 d after treatment. Townline Lake plants responded differently from susceptible plants when treated with fluridone, norflurazon, and topramezone at 40 µg L−1. These results indicate that the Townline population of hybrid watermilfoil has inherent tolerance to multiple herbicide modes of action. These results are especially significant as topramezone has recently been labeled for aquatic use. Screening of additional herbicides to determine potential herbicide tolerance of the Townline Lake population is recommended.


2020 ◽  
Vol 30 (4) ◽  
pp. 615-621
Author(s):  
Xingxing Li ◽  
Dongliang Liu ◽  
Zhaowei Wu ◽  
Dan Li ◽  
Yifei Cai ◽  
...  

2011 ◽  
Vol 187 (7) ◽  
pp. 3785-3797 ◽  
Author(s):  
Laurent Verkoczy ◽  
Yao Chen ◽  
Hilary Bouton-Verville ◽  
Jinsong Zhang ◽  
Marilyn Diaz ◽  
...  

Author(s):  
Thomas L. Dresner ◽  
Philip Barkan

Abstract The allocation of individual tolerances that form critical stack-ups is an important task in mechanical design. It is desirable, but difficult in practice, to allocate tolerances to obtain all required stack-ups at minimum cost. A minimum-cost allocation method is proposed here that works for both a single tolerance stack-up and for multiple tolerance stack-ups that share one or more individual tolerances. Tolerances can be optimally allocated for both worst case and a variety of 6σ statistical cases. The method is applicable to one-dimensional stack-ups and to multi-dimensional stack-ups with known sensitivity functions. It is a numerical Lagrange multiplier method that is more general than the Lagrange multiplier methods that have often been proposed. The basic method will almost always provide the lowest cost result when the manufacturing process to produce each toleranced dimension has been firmly established in advance. An exact method for efficiently extending the basic method to determine the lowest cost process for producing each dimension is also introduced.


Sign in / Sign up

Export Citation Format

Share Document