On Ground Settlement Rate Approach of Preloading Method

2013 ◽  
Vol 353-356 ◽  
pp. 258-264
Author(s):  
Ming Lei Shi ◽  
Rui Kun Zhang ◽  
Hao Zhang
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Ground Settlement ◽  
Settlement Rate ◽  
Excess Pore Water Pressure ◽  
Surcharge Preloading ◽  
The Relationship ◽  
Preloading Method ◽  
Linear Compressibility ◽  
Excess Pore

Based on the theory of the Terzaghi 1-D consolidation and the linear compressibility of soil, a rational method for regionalization of recompression and compression in the distribution of the excess pore-water pressure under overloading-unloading was presented. A simple generalized expression of the ground settlement rate applied to insufficient-load preloading, equal-load preloading, surcharge preloading and a time expression of insufficient-load preloading, surcharge preloading relative to equal-load preloading were further derived. The relationship mechanism of settlement rate and time of insufficient-load preloading, surcharge preloading relative to equal-load preloading are discussed based on the same allowed post-construction settlement.

Security Control Method of Loading for Surcharge Preloading Based on the Stress Path

2011 ◽  
Vol 368-373 ◽  
pp. 2795-2803
Author(s):  
Heng Hu ◽  
Yan Li ◽  
Zhi Liang Dong ◽  
Yan Luo ◽  
Gong Xin Zhang
Keyword(s):  
Pore Water ◽  
Safety Factor ◽  
Control Method ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Stress Path ◽  
Excess Pore Water Pressure ◽  
Surcharge Preloading ◽  
Security Control ◽  
Excess Pore

All the time, security control method of loading is an important research part in the surcharge preloading, which is directly related to safety of the construction process. Starting from the stress path, discussing the variation of excess pore water pressure and relationship between stress path and security, and bringing forward the control method with a safety factor Fs based on the stress path. By measuring the change of excess pore water pressure, the control method with a safety factor Fs can reflect quantitatively the security status of soil and achieve the purpose of the process control, finally the security control method including the safety factor of loading and speed control is put forward to monitor construction safety. The safety factor of loading Fs is verified and back analyzed with the finite-element software, getting the correction factor from 0.90 to 1.20.

scholarly journals EVALUASI SETTLEMENT MENGGUNAKAN SURCHARGE PRELOADING DENGAN PVD PADA PROYEK DI BANDUNG SELATAN

2020 ◽  
Vol 3 (3) ◽  
pp. 911
Author(s):  
Michael Christopher Yapriadi ◽  
Inda Sumarli ◽  
Ali Iskandar
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soil Improvement ◽  
Soil Layers ◽  
Excess Pore Water Pressure ◽  
Surcharge Preloading ◽  
Improvement Method ◽  
Degree Of Consolidation ◽  
Excess Pore

The development in Indonesia continues to grow. Hence, the feasible land for construction is drastically decreased. However, some projects must be constructed on that kind of land. One solution to solve this problem is by using a soil improvement. A project in Bandung Selatan chose to apply Surcharge Preloading with PVD soil improvement method. This project used a combination of 9,2 metres surcharge preload and a 28 metres depth PVD, with triangular formation and 1,2 metres spacing. The soil improvement was finished after 548 days. This analysis aims to evaluate the settlement from the soil improvement result, which is 1,297 metres. This analysis uses a finite difference method program. The excess pore water pressure from the analysis result is 0,229 T/m2 on the 548th day. Therefore, these soil layers have possibilities to settle again in future. The 90% degree of consolidation settlement for this soil layers is 2,31 metres, which will be reached on the 813,4th days. It is suspected that there are some mistakes either during the soil improvement designing or the soil improvement process. Pembangunan di Indonesia terus berkembang. Akibatnya jumlah tanah yang baik untuk proyek konstruksi semakin menipis. Kendati demikian, ada kalanya suatu proyek harus dilaksanakan di lokasi tersebut. Salah satu solusi yang dapat ditempuh adalah dengan melakukan perbaikan tanah. Sebuah proyek di Bandung Selatan melakukan perbaikan tanah dengan metode Surcharge Preloading dengan PVD. Proyek ini menggunakan kombinasi antara timbunan setinggi 9,2 meter dan PVD sedalam 28 meter, dengan formasi segitiga yang dipasang dengan jarak antar PVD 1,2 meter. Perbaikan tanah dilakukan selama 548 hari. Analisis ini bertujuan melakukan evaluasi terhadap kurang maksimalnya penurunan di lapangan yang hanya mencapai 1,297 meter. Analisis dilakukan dengan bantuan program beda hingga. Berdasarkan hasil analisis, besarnya excess pore water pressure pada hari ke-548 adalah 0,229 T/m,2, sehingga lapisan tanah tersebut masih memiliki potensi untuk mengalami penurunan. Adapun penurunan konsolidasi 90% yang dapat terjadi sebesar 2,31 meter pada hari ke-813,4. Diduga terdapat kesalahan baik dalam perhitungan perencanaan awal ataupun saat pelaksanaan di lapangan.

scholarly journals Acceleration of Debris Flow Due to Granular Effect

2021 ◽  
Vol 9 ◽  
Author(s):  
Taiqiang Yang ◽  
Yong Li ◽  
Xiaojun Guo ◽  
Jun Zhang ◽  
Yu Jiang ◽  
...  
Keyword(s):  
Debris Flow ◽  
Pore Water ◽  
Slip Surface ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Coarse Grained ◽  
Flow Depth ◽  
Excess Pore Water Pressure ◽  
The Relationship ◽  
Excess Pore

Pore water pressure has been recognized as an important factor to enhance the mobility of debris flow moving in channel of very gentle slope. The creation and dissipation of pore water pressure are associated with interaction between grains. This study proposes a physical model for the pressure on mobility of flows with different granular configurations: the flow with overlying coarse-grained layer (i.e., inverse grading) and the flow with fully-mixed grains. The flow velocity is derived by the effective stress principle and the relationship between acceleration and pore water pressure is analyzed under different conditions. The results show that a high excess pore water pressure leads to high velocity of flow, and the pressure increases during the movement; and acceleration increases with time and flow depth under given pore water pressure. Moreover, compared with the flow with mixed grains, the flow with overlying coarse-grained layer is more effective to promote the excess pore water pressure and the liquefaction slip surface. Therefore, the internal drag reduction due to pore water pressure produces an acceleration effect on the flow.

Shaking Table Test on the Improvement Dimension of Permeable Grouting Method for Liquefaction Countermeasure

2009 ◽  
Author(s):  
Masakazu Kobayashi ◽  
Kouki Zen ◽  
Guangqi Chen ◽  
Kiyonobu Kasama ◽  
Kentaro Hayashi
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Shaking Table ◽  
Wave Form ◽  
Ground Settlement ◽  
Acceleration Response ◽  
Excess Pore Water Pressure ◽  
Excess Pore ◽  
Improvement Ratio

In order to clarify an optimum improvement dimension for the permeable-grouting method as a liquefaction countermeasure, a series of shaking table tests have been conducted for improved model grounds with various improvement dimensions. To express the variety of improvement dimensions in field, the model ground was created by dividing it into two types of mesh elements, in which each mesh element was simplified as a liquefiable element (unimproved element) or non-liquefiable element (improved element) respectively. Improvement ratio defined by the volume ratio of improved elements in total elements was set for 0% or 50% and the width of mesh element was 50mm. The acceleration of shaking table was applied by step loading; 100, 200, 300 and 400gal with the sinusoidal wave form of 3Hz. In order to investigate the seismic behavior of the improved ground, pore water pressure transducers and acceleration meters were set in the model ground. The main conclusions obtained from this study are as follows; 1) Both of the ground settlement induced by liquefaction and the acceleration response during seismic loading are greatly affected by the generated excess pore water pressure depending on the improvement dimension. Therefore, the “liquefiable region” in which the excess pore water pressure ratio is more than 0.75 is newly defined to evaluate the effect of improvement dimension on the acceleration response of ground, excess pore water pressure and vertical settlement, 2) As improved element increases in the liquefiable region, both of the excess pore water pressure in liquefiable element and the acceleration response of ground surface decrease. Namely, the improvement ratio in the liquefiable region could be an important index to evaluate the effect of improvement, 3) From the experimental conditions in this paper, it is suggested that 300mm is the best vertical interval and 150mm is the worst one to reduce the ground settlement induced by liquefaction and the vibration of ground.

scholarly journals Mechanical behaviour of calcareous waste under consolidated drained triaxial compression testing in saturated conditions

2019 ◽  
Vol 106 ◽  
pp. 01016
Author(s):  
Jakub Zięba
Keyword(s):  
Mechanical Behaviour ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Soil Samples ◽  
Excess Pore Water Pressure ◽  
Stiffness Properties ◽  
Construction Purpose ◽  
Strength And Stiffness ◽  
Excess Pore

The article presents the mechanical behaviour of calcareous waste under consolidated and drained condition in Triaxial compression test (CD). The host material currently being considered for the construction purpose of several buildings in Poland. One of the location of calcareous waste is in Łagiewniki area (in Cracow) [1,2]. In this work, particular attention has been paid to the to ensure fully saturation for all the tested soil samples and avoid generation of unwanted excess pore water pressure during shearing stage. The saturation level of soil samples was estimated based on Skempton’s law (B>0.95). CD Triaxial test have been conducted in order to derive information on its strength and stiffness properties.

Stress–strain pattern–based criterion to assess cyclic shear resistance of soil from laboratory element tests

2016 ◽  
Vol 53 (9) ◽  
pp. 1460-1473 ◽  
Author(s):  
Dharma Wijewickreme ◽  
Achala Soysa
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Shear Stiffness ◽  
Large Strains ◽  
Fundamental Parameter ◽  
Stress Strain ◽  
Cyclic Shear ◽  
Excess Pore Water Pressure ◽  
Excess Pore

The cyclic shear response of soils is commonly examined using undrained (or constant-volume) laboratory element tests conducted using triaxial and direct simple shear (DSS) devices. The cyclic resistance ratio (CRR) from these tests is expressed in terms of the number of cycles of loading to reach unacceptable performance that is defined in terms of the attainment of a certain excess pore-water pressure and (or) strain level. While strain accumulation is generally commensurate with excess pore-water pressure, the definition of unacceptable performance in laboratory tests based purely on cyclic strain criteria is not robust. The shear stiffness is a more fundamental parameter in describing engineering performance than the excess pore-water pressure alone or shear strain alone; so far, no criterion has considered shear stiffness to determine CRR. Data from cyclic DSS tests indicate consistent differences inherent in the patterns between the stress–strain loops at initial and later stages of cyclic loading; instead of relatively “smooth” stress–strain loops in the initial parts of loading, nonsmooth changes in incremental stiffness showing “kinks” are notable in the stress–strain loops at large strains. The point of pattern change in a stress–strain loop provides a meaningful basis to determine the CRR (based on unacceptable performance) in cyclic shear tests.

Consolidation Theory for Composite Ground with Granular Columns Based on Different Calculation Models

2011 ◽  
Vol 261-263 ◽  
pp. 1534-1538
Author(s):  
Yu Guo Zhang ◽  
Ya Dong Bian ◽  
Kang He Xie
Keyword(s):  
Pore Water ◽  
Analytical Solutions ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Vertical Flow ◽  
Excess Pore Water Pressure ◽  
Consolidation Theory ◽  
Composite Ground ◽  
Granular Column ◽  
Excess Pore

The consolidation of the composite ground under non-uniformly distributed initial excess pore water pressure along depth was studied in two models which respectively considering both the radial and vertical flows in granular column and the vertical flow only in granular column, and the corresponding analytical solutions of the two models were presented and compared with each other. It shows that the distribution of initial excess pore water pressure has obvious influence on the consolidation of the composite ground with single drainage boundary, and the rate of consolidation considering the radial-vertical flow in granular column is faster than that considering the vertical flow only in granular column.

The Test Study to the Changes of Excess Pore Water Pressure during Precast Pile Construction

2012 ◽  
Vol 193-194 ◽  
pp. 1010-1013
Author(s):  
Shu Qing Zhao
Keyword(s):  
Pore Water ◽  
Clayey Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Excess Pore Pressure ◽  
Soil Pressure ◽  
Excess Pore Water Pressure ◽  
Test Study ◽  
Excess Pore

The construct to precast pile in thick clayey soil can cause the accumulation of excess pore water pressure. The high excess pore pressure can make soil, buildings and pipes surrounded have large deflection, even make them injured. Combining with actual projects, this paper presents an in-situ model test on the changes of excess pore water pressure caused by precast pile construct. It is found that the radius of influence range for single pile driven is about 15m，the excess pore water pressure can reach or even exceed the above effective soil pressure, and there are two relatively stable stages.

A Practical Saturated Sand Elastic-Plastic Dynamic Constitutive Model and Application

2012 ◽  
Vol 446-449 ◽  
pp. 1621-1626 ◽  
Author(s):  
Yan Mei Zhang ◽  
Dong Hua Ruan
Keyword(s):  
Constitutive Model ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Stone Columns ◽  
Saturated Sand ◽  
Multidimensional Model ◽  
Excess Pore Water Pressure ◽  
Elastic Plastic ◽  
Excess Pore

A practical saturated sand elastic-plastic dynamic constitutive model was developed on the base of Handin-Drnevich class nonlinear lag model and multidimensional model. In this model, during the calculation of loading before soil reaches yielding, unloading and inverse loading, corrected Handin-Drnevich equivalent nonlinear model was adopted; after soil yielding, based on the idea of multidimensional model, the composite hardening law which combines isotropy hardening and follow-up hardening, corrected Mohr-Coulomb yielding criterion and correlation flow principle were adopted. A fully coupled three dimension effective stress dynamic analysis procedure was developed on the base of this model. The seismic response of liquefaction foundation reinforced by stone columns was analyzed by the developed procedure. The research shows that with the diameter of stone columns increasing, the excess pore water pressure in soil between piles decreases; with the spacing of columns increasing, the excess pore water pressure increases. The influence of both is major in middle and lower level of composite foundation.

Sign in / Sign up

Export Citation Format

Share Document