Evaluation of the mechanical anisotropy of lacustrine smectite clays by triaxial test analysis

This paper describes the role of fabric anisotropy during clayey soil deformation. A set of triaxial tests was performed on vertical and horizontal specimens of undisturbed smectite lake sediments from Jurica, Queretaro in Mexico. The results allowed to analyze the influence of bedding and discontinuities on the mechanical behavior of Jurica clays after failure. Tests with applied low strain rates allowed pore pressure equalization within specimens with different gravimetric water content and degree of saturation. Shear failure results of undrained tests showed that deformation distributes differently in both horizontal and vertical directions and that stress may be dissipated by pore collapses, fractures and particle deformation. The experimental evidence suggests that microfabric is a relevant variable in the overall mechanical response of clayey sediments that depends on the natural fabric (bedding and discontinuities), mineralogy, and water content. A detailed analysis of Young´s Moduli (E) showed the high variability of this parameter from 108 to 409 kg/cm2 (calculated at 30% of σdmax) and its dependence on the orientation of the specimen and the water content. In addition, p’-q’ graphs illustrate the relevance of considering mechanical anisotropy in clays and provide further insights to understand the role of smectites in progressive shear deformation.

Mechanical Properties of Rammed Earth Stabilized with Local Waste and Recycled Materials

Traditional techniques of construction using natural and locally available materials are nowadays raising the interest of architects and engineers. Clayey soil is widely present in all continents and regions, and where available it is obtained directly from the excavation of foundations, avoiding transportation costs and emissions due to the production of the binder. Moreover, raw earth is recyclable and reusable after the demolition, thanks to the absence of the firing process. The rammed earth technique is based on earth compressed into vertical formworks layer by layer to create a wall. This material owes its strength to the compaction effort and due to its manufacture procedure exhibits layers resembling the geological strata and possessing high architectural value. The hygroscopic properties of rammed earth allow natural control of the indoor humidity, keeping it in the optimal range for human health. Stabilization with lime or cement is the most common procedure to enhance the mechanical and weather resistance at once. This practice compromises the recyclability of the earth and reduces the hygroscopic properties of the material. The use of different natural stabilizers, fibers, and natural polymers by-products of the agriculture and food industry, can offer an alternative that fits the circular economy requirements. The present study analyses the mechanical strength of an Italian earth stabilized with different local waste and recycled materials that do not impair the final recyclability of the rammed earth.

Numerical Modeling of Shallow Foundation Behavior Using Soft Soil Model

This study discusses the results of simulation a finite element analysis of the load-settlement curve using soft soil model of shallow foundation subjected to axial load rested on three different types of clayey soils, it was considered different shear strength parameters (C=16, C=25, and C=70). It was concluded for clayey soil of C=16, there was a match to the experimental load – settlement curve using the soft soil model. It was also observed increase in the foundation width led to an increase in bearing capacity, however, bearing capacity increased by around (79 %) for an increase in footing width of (6.25), so it was about (144%) for (12.5).

Freeze-Thaw Behavior of Stabilized Clayey Soil with Red Mud and Cement

The clayey soils in areas with seasonal frost are exposed to at least one freeze-thaw cycle every year and worsen their engineering properties. To prevent the engineering properties of clayey soils, it is necessary to improve the freeze-thaw resistance of them. In this study, the clayey soil was stabilized by using red mud and cement additive materials. Prepared samples of clayey soil and stabilized clayey soil were subjected to the unconfined compressive test. To investigate the effects of red mud and cement additive materials on the freeze-thaw resistance of clayey soil, the natural and stabilized expansive soil samples were exposed to the freeze-thaw cycles under laboratory conditions. The obtained results showed that the red mud and cement additive materials increased the freeze-thaw resistance of clayey soil. Consequently, it was concluded that red mud and cement additive materials can be successfully used to improve the freeze-thaw resistance of clayey soils.

Geo-Engineering Study of Selected Soils for Cement Industry in Al-Kifil District, Babylon, Central Iraq

The research was conducted on nine pits for selected soils in Babylon, in the Al-Kifl region in particular. It aims to find the relationship between the physical and chemical properties of the studied soil and its suitability in the cement industry. Nine samples of different depths were taken with a simple description of the soil in the fieldwork stage. As for the stage of laboratory tests, it included testing the grain size distribution to find the percentage of sand, silt, and clay, and Atterberg limits to find plasticity. It was found through these tests that the soil is silty clay and has low plasticity except for samples no. 5, and 6, which were clayey soil with low plasticity. The relationship between physical properties depends on the property of the grain size distribution, as it is the function of the rest of the properties. Chemical tests of the samples and comparing the ratios of their oxides with the standard specifications of the Kufa plant laboratory turned out to be suitable for the manufacture of ordinary Portland cement, as the study area is considered a good quarry for the clays used in such industries.