Effects of Tip Clearance Size on Flowfield in a Low-Speed Axial Compressor Rotor

2014 ◽  
Vol 543-547 ◽  
pp. 158-163 ◽  
Author(s):  
Zhen Zhen Duan ◽  
Yang Wei Liu ◽  
Li Peng Lu
Keyword(s):  
Flow Condition ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Primary Role ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Overall Performance ◽  
Corner Vortex

The simulations of a low-speed axial compressor rotor with two tip clearance sizes, 0.5% chord and 1.5% chord, were performed in the study. Overall performance and detailed flow fields at near stall condition are analyzed. The results show that the rotor stall occurs at higher mass flow condition with large tip clearance. For the small tip clearance the tip leakage vortex and the corner vortex both contribute significantly to the rotor stall, and the interaction between the vortices promotes the stall generation. While for the large tip clearance the tip leakage vortex plays a primary role, and the vortices interaction is ignorable.

Numerical Investigation of the Behavior of Tip Leakage Flow in a Low-Speed Axial Compressor Rotor at Near-Stall Condition

2012 ◽  
Author(s):  
Zhenzhen Duan ◽  
Yangwei Liu ◽  
Lipeng Lu
Keyword(s):  
Axial Compressor ◽  
Rotating Stall ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Stall Inception ◽  
Low Speed ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Corner Vortex

In the present work, time-accurate simulations were performed to investigate the unsteady flow fields in the tip region of a low-speed large-scale axial compressor rotor at near-stall condition. Firstly, the steady performance characteristic of the rotor was obtained by steady simulations. Secondly, a series of unsteady simulations were carried out to investigate the physical processes as the rotor approaching stall and the role of complex tip flow mechanism on flow instability in the rotor. The characteristics of tip leakage vortex were compared between design condition and near-stall condition. Detailed analyses were then employed to emphasize the development of stall inception and the comprehensions of the internal flow field. Two flow phenomena, spillage at the leading edge and backflow at the trailing edge, are found beyond the flow solution limit, which are both linked to the tip leakage flow. And the breakdown of the tip leakage vortex has been captured. The flow visualization and the quantification of passage blockage expose that the tip leakage vortex and corner vortex contribute most to the total passage blockage. Therefore, they are considered to be the key flow structures contributing to the rotating stall. Further analyses indicate that, in the current rotor, the interaction of the tip leakage flow and the corner vortex is clarified to be the key factor that leads to the rotating stall. In addition, the very initial disturbances of stall inception are discussed. And the interaction of the boundary layer migration on the blade suction side and the tip leakage vortex also plays a significant role in the stall inception.

Characteristics of the Tip Leakage Vortex in a Low-Speed Axial Compressor With Different Rotor Tip Gaps

2012 ◽  
Author(s):  
Zhibo Zhang ◽  
Xianjun Yu ◽  
Baojie Liu
Keyword(s):  
Axial Compressor ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Stereoscopic Particle Image Velocimetry ◽  
Tip Clearance ◽  
Test Facility ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage

The detailed evolutionary processes of the tip leakage flow/vortex inside the rotor passage are still not very clear for the difficulties of investigating of them by both experimental and numerical methods. In this paper, the flow fields near the rotor tip region inside the blade passage with two tip gaps, 0.5% and 1.5% blade height respectively, were measured by using stereoscopic particle image velocimetry (SPIV) in a large-scale low speed axial compressor test facility. The measurements are conducted at four different operating conditions, including the design, middle, maximum static pressure rise and near stall conditions. In order to analyze the variations of the characteristics of the tip leakage vortex (TLV), the trajectory, concentration, size, streamwise velocity, and the blockage parameters are extracted from the ensemble-averaged results and compared at different compressor operating conditions and tip gaps. The results show that the formation of the TLV is delayed with large tip clearance, however, its trajectory moves much faster in an approximately linear way from the blade suction side to pressure side. In the tested compressor, the size of the tip gap has little effects on the scale of the TLV in the spanwise direction, on the contrary, its effects on the pitch-wise direction is very prominent. Breakdown of the TLV were both found at the near-stall condition with different tip gaps. The location of the initiation of the TLV breakdown moves downstream from the 60% chord to 70% chord as the tip gap increases. After the TLV breakdown occurs, the flow blockage near the rotor tip region increases abruptly. The peak value of the blockage effects caused by the TLV breakdown is doubled with the tip gap size increasing from 0.5% to 1.5% blade span.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

Numerical Study on Tip Leakage Flow Structure of an Axial Flow Compressor Rotor

2014 ◽  
Author(s):  
Chenkai Zhang ◽  
Jun Hu ◽  
Zhiqiang Wang ◽  
Wei Yan ◽  
Chao Yin ◽  
...  
Keyword(s):  
Flow Structure ◽  
Large Scale ◽  
Numerical Study ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage

To deepen the knowledge of tip leakage flow/vortex flow structure in the tip clearance of axial compressor rotors, this paper presents steady numerical studies on a subsonic rotor. The rotor and its related low-speed large-scale repeating-stage axial compressor are used for low-speed model testing of a modern high-pressure compressor. Results were first compared with available experimental data to validate adopted numerical method. Then complex endwall flow structure and flow loss mechanism at design operating point were studied. At last, comparisons were made for tip leakage vortex structure, interface of the leakage flow/main flow, endwall blockage and loss between design and near-stall operating points. Results show that only the spilled flows below 62.5% clearance height at the leading edge will roll into tip leakage vortex for this rotor. In addition, tip leakage vortex plays a secondary important role for higher positions, where secondary leakage flow occurs and occupies broader chordwise range. Although tip leakage vortex would expand and strongly mix with the mainflow when it propagates downstream, which leads to a rapid reduction of the normalized streamwise vorticity, the value of the normalized helicity shows that concentrated vortex feature is still maintained.

Impact of Sinusoidal Tip Gaps on Axial Compressor Rotor Performance: A Flow Field Investigation

2019 ◽  
Author(s):  
Shraman Goswami ◽  
Ashima Malhotra
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Field Investigation ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Stall Margin ◽  
Tip Leakage ◽  
Compressor Rotor

Abstract Performance of an axial compressor rotor depends largely on the tip leakage flow. Tip leakage flow results in tip leakage vortex which is a source of loss. This has an impact on the compressor efficiency as well as stall margin. A lot of work has been done to understand the tip leakage flow and controlling the same. Active and passive stall margin improvement methods mainly target the tip leakage vortex. In the current study, numerical investigations are carried out to understand flow fields near tip region of rotors. The blade tip designed to have a tip gap as sine and cosine waves (single and double waves). Numerical methodology is validated with NASA Rotor37 test results. The performance parameters of the rotors with modified tip gap shapes are compared with constant tip clearance rotor. A detailed flow field investigation is presented to compare the tip flow structure and its impact on overall performance of the compressor.

Periodic Unsteadiness of Tip Clearance Vortex in an Axial Compressor Rotor

2020 ◽  
Author(s):  
Fan Yang ◽  
Yanhui Wu ◽  
Ziyun Zhang ◽  
Zhenyang Wang
Keyword(s):  
Vortex Core ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Small Range ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Periodic Fluctuations ◽  
Tip Clearance Vortex

Abstract A series of unsteady simulations, supported by experimental data, are used to characterize the periodic unsteadiness of the tip clearance vortex in an axial compressor rotor. The numerical probes detect significant periodic fluctuations in the blade tip region at near stall conditions. A reduced frequency at different condition is limited to a small range although there exist a large difference on the natural frequency. Physical explanations of the periodic fluctuations are made in terms of vortex-core identification, contour, etc. The nature of the periodic unsteadiness in the tip region is the periodic bubble-type breakdown of the tip leakage vortex induced by the broken vortex core generated by the previous breakdown. The life cycle of the broken vortex core can be summarized as three processes, generation, propagation and inducing breakdown of tip leakage vortex. The broken vortex core arrives at mid-chord of the adjacent blade, resulting in change of momentum in the tip clearance and pressure in the leading edge of the adjacent blade. The flow in this blade tip region is similarly affected by another adjacent blade. The tip leakage vortex core is bent, then the breakdown of tip clearance happens and a new broken vortex core appears accompanied by a back flow region.

Effects of Tip Clearance on the Stall Inception Process in an Axial Compressor Rotor

2013 ◽  
Author(s):  
Kazutoyo Yamada ◽  
Hiroaki Kikuta ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Yasunori Hara
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Stall Inception ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Flow Phenomena ◽  
Casing Pressure

The paper presents experimental and numerical studies on the effects of tip clearance on the stall inception process in a low-speed axial compressor rotor with a large tip clearance. It has been revealed that in the small tip clearance case, shortly after the spike disturbance which results from the leading-edge separation near the rotor tip appears, the tornado-like vortex is generated by the separation, and soon the compressor falls into stall. In the large tip clearance case, the experiment showed that the performance characteristic differs from that in the small tip clearance case at near-stall conditions. This implies that the stall inception process differs with the tip clearance size. The flow phenomenon in the stall inception leading to such difference has been investigated in this study. Pressure and velocity fields which were ensemble-averaged and phase-locked by the periodic multi-sampling technique were measured on the casing wall and downstream of the rotor, respectively. In addition, to capture the unsteady flow phenomena inside the rotor, “Instantaneous Casing Pressure Field Measurement” was carried out: instantaneous casing pressure fields in one rotor passage region were measured by 30 high response pressure transducers mounted on the casing wall. In order to investigate further details of near-stall flow field for the large tip clearance, DES (Detached Eddy Simulation) has been conducted using a computational mesh with 120 million points. The results are compared with those from previous studies for the small tip clearance. As expected, the measurement results show notable differences in the near-stall flow field between the two tip clearance cases. The results from the casing pressure measurement show that high pressure fluctuation appears on the pressure side near the rotor leading-edge in the large tip clearance case. In the result of the velocity field measurement downstream of the rotor, high turbulence intensity is found near the casing in the large tip clearance case. The numerical results reveal that the vortex breakdown occurs in the tip leakage vortex and induces the oscillation of the tip leakage vortex with its unsteady nature. The flow phenomena confirmed in the experimental results are clearly explained by considering the breakdown of the tip leakage vortex. The vortex breakdown gives rise to not only large blockage but also the rotating disturbance through the interaction of the fluctuating tip leakage vortex with the pressure surface of the adjacent blade, and governs the stall inception process.

101 Interaction of Tip Leakage Vortex with Shock Wave in a Transonic Axial Compressor Rotor

2000 ◽  
Vol 2000.53 (0) ◽  
pp. 1-2
Author(s):  
Kazutoyo YAMADA ◽  
Yoshinori TAGUCHI ◽  
Kazuhisa SAIKI ◽  
Masato FURUKAWA ◽  
Masahiro INOUE
Keyword(s):  
Shock Wave ◽  
Axial Compressor ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

scholarly journals Active flow control at a 1.5-stage low-speed research compressor with varying rotor tip clearance

2011 ◽  
Vol 225 (7) ◽  
pp. 886-896 ◽  
Author(s):  
M Künzelmann ◽  
R Urban ◽  
R Mailach ◽  
K Vogeler
Keyword(s):  
Flow Control ◽  
Active Flow Control ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Low Speed ◽  
Operating Range ◽  
Compressor Rotor ◽  
Active Flow

The stable operating range of axial compressors is limited by the onset of rotating stall and surge. Mass injection upstream of the tip of an axial compressor rotor is a stability enhancement approach which can be effective in suppressing stall in tip-critical rotors, and thus increasing the operating range of compressors. In this article, investigations on active flow control related to the rotor tip gap sensitivity are discussed. The experiments were performed in a 1.5-stage low-speed research compressor. Measurements at part speed (80 per cent) and full speed (100 per cent) with varying injection rates are discussed. These tests were performed for two rotor tip clearances of 1.3 per cent and 4.3 per cent of rotor blade tip chord. Results on the compressor map, the flow field as well as transient measurements to identify the stall inception are discussed. Supplementary, the numerical results are compared to the experiments based on the configuration with the greatest benefit in operating range enhancement.

Desensitization of Axial Compressor Performance and Stability to Tip Clearance Size

2015 ◽  
Author(s):  
Engin Erler ◽  
Huu Duc Vo ◽  
Hong Yu
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Aerodynamic Stability ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Flow Features ◽  
Parametric Studies ◽  
Compressor Performance ◽  
Flow Effects ◽  
Stagger Angle

This paper presents a computational and analytical study to identify and elucidate fundamental flow features associated with the desensitization of performance and aerodynamic stability of an axial compressor rotor to tip clearance change. Parametric studies of various design change on a baseline double circular arc axial rotor led to the identification of two flow features associated with reducing sensitivity to tip clearance, namely high incoming meridional momentum in the tip region and reduction/elimination of double tip leakage. Numerical experiments were subsequently performed on the baseline rotor geometry to validate these two flow features and explain the associated flow physics by variations in incoming meridional momentum and pitch size. Finally, two designs were proposed, namely full forward chordwise sweep and partially low stagger angle, to exploit these flow features. The results indicated that both designs produce the intended flow effects and exhibit lower performance and aerodynamic stability sensitivity to tip clearance.

Sign in / Sign up

Export Citation Format

Share Document