Laser Cladding of Stainless Steel Substrates with Stellite 6

2013 ◽  
Vol 773-774 ◽  
pp. 573-589 ◽  
Author(s):  
Alain Kusmoko ◽  
D. Dunne ◽  
H. Li ◽  
D. Nolan
Keyword(s):  
Stainless Steel ◽  
Laser Cladding ◽  
Testing Machine ◽  
Austenitic Stainless Steels ◽  
Wear Test ◽  
Wear Testing ◽  
Test Results ◽  
Stellite 6 ◽  
Steel Substrates ◽  
Spectroscopy Optical

Stellite 6 coatings were produced using laser cladding of two different steel substrates (martensitic and austenitic stainless steels). The chemical composition and microstructure of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was examined using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the martensitic stainless steel (SS) substrate. The wear test results showed that the weight loss for the coating on martensitic SS was significantly lower than for the austenitic SS substrate. It is concluded that the higher hardness of the coating on the martensitic SS, together with the harder and more rigid substrate increase the wear resistance of the Stellite 6 coating.

Dilution and C Content Estimation of Stellite 6 Fabricated on a 1050 Steel Substrate by Laser Cladding

2017 ◽  
Vol 263 ◽  
pp. 131-136
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li
Keyword(s):  
Laser Cladding ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Test ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Test Results ◽  
Stellite 6 ◽  
Service Conditions ◽  
Stellite Coating

Stellite 6 was fabricated by laser cladding on a 1050 steel (MS) substrate with laser powers of 1 kW (MS-1) and 1.8 kW (MS-1.8). The chemical compositions and microstructures of the coatings were analysed by X-Ray Fluoroscense, optical microscopy and scanning electron microscopy. The microhardness of the coatings was examined and the wear mechanism of the coatings was evaluated using a ball-on-plate wear testing machine. The results indicated less cracking and pore development for Stellite 6 coatings applied to the 1050 steel substrate with the lower laser power (MS-1). Moreover, the Stellite coating for MS-1 was significantly harder than that obtained for MS-1.8. The wear test results showed that the weight loss for MS-1 was much lower than for MS-1.8. The evaluations of dilution and calculation of carbon content indicated that MS-1 has lower dilution and higher coating C content than MS-1.8. It is concluded that the lower hardness of the coating for MS-1.8, substantially reduced the wear resistance of the Stellite 6 coating and the lower hardness of the coating for MS-1.8 was due to higher level of dilution and lower coating C content. The coating-substrate couple must be considered in assessing the likely performance of the coating under service conditions.

Laser Cladding of Wear Resistant Stellite 6 Coating on P22 Steel Substrate with Two Different Energy Inputs

2014 ◽  
Vol 911 ◽  
pp. 97-101 ◽  
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li ◽  
David Nolan
Keyword(s):  
Laser Cladding ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Test ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Stellite 6 ◽  
Energy Inputs ◽  
Stellite Coating ◽  
Spectroscopy Optical

Stellite 6 was deposited by laser cladding on a P22 steel substrate with energy inputs of 1 kW (P22-1) and 1.8 kW (P22-1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was examined using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the P22 steel substrate with the lower heat input (P22-1). Further, the Stellite coating for P22-1 was significantly harder than that obtained for P22-1.8. The wear test results showed that the weight loss for P22-1 was much lower than for P22-1.8. It is concluded that the lower hardness of the coating for P22-1.8, markedly reduced the wear resistance of the Stellite 6 coating.

Evaluation of Two Different Energy Inputs for Deposition of Stellite 6 by Laser Cladding on a Martensitic Stainless Steel Substrate

2015 ◽  
Vol 1119 ◽  
pp. 628-632
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li
Keyword(s):  
Stainless Steel ◽  
Laser Cladding ◽  
Martensitic Stainless Steel ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Stellite 6 ◽  
Energy Inputs

Stellite 6 was deposited by laser cladding on a martensitic stainless steel substrate with energy inputs of 1 kW (MSS-1) and 1.8 kW (MSS-1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was assessed using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the MSS steel substrate with the lower heat input (MSS-1). Further, the Stellite coating for MSS-1 was significantly harder than that obtained for MSS-1.8. The wear test results indicated that the weight loss for MSS-1 was much lower than for MSS-1.8. It is concluded that the lower hardness of the coating for MSS-1.8, markedly reduced the wear resistance of the Stellite 6 coating.

scholarly journals Wear Behaviour of Stellite 6 Coatings Produced on an Austenitic Stainless Steel Substrate by Laser Cladding Using Two Different Heat Inputs

2014 ◽  
Vol 619 ◽  
pp. 13-17 ◽  
Author(s):  
Alain Kusmoko ◽  
Druce P. Dunne ◽  
Hui Jun Li
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Laser Cladding ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Chemical Compositions ◽  
Stellite 6

Stellite 6 was deposited by laser cladding on an austenitic stainless steel substrate (ASS) with energy inputs of 1 kW (ASS 1) and 1.8 kW (ASS 1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was assessed using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the austenitic stainless steel substrate with the lower heat input (ASS 1). Further, the Stellite coating for ASS 1 was significantly harder than that obtained for ASS 1.8. The wear test results showed that the weight loss for ASS 1 was much lower than for ASS 1.8. It is concluded that the lower hardness of the coating for ASS 1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

Study of Laser Cladding of Stellite 6 on Nickel Superalloy Substrate with Two Different Energy Inputs

2014 ◽  
Vol 896 ◽  
pp. 600-604
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li ◽  
David Nolan
Keyword(s):  
Laser Cladding ◽  
Testing Machine ◽  
Wear Test ◽  
Nickel Superalloy ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Stellite 6 ◽  
Substrate Structure ◽  
Energy Inputs ◽  
Stellite Coating

Stellite 6 was deposited by laser cladding on a nickel superalloy substrate (NIS) with energy inputs of 1 kW (NIS 1) and 1.8 kW (NIS 1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was examined using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the nickel superalloy substrate with the lower heat input (NIS 1). Further, the Stellite coating for NIS 1 was significantly harder than that obtained for NIS 1.8. The wear test results showed that the weight loss for NIS 1 was much lower than for NIS 1.8. It is concluded that the lower hardness of the coating for NIS 1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

Surface Morphology and Wear Analysis of Stellite 6 Deposited on 9Cr-1Mo Steel Substrate by Laser Cladding

2015 ◽  
Vol 1119 ◽  
pp. 640-644
Author(s):  
Alain Kusmoko ◽  
Hui Jun Li
Keyword(s):  
Laser Cladding ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Test ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Force Microscopy ◽  
Stellite 6 ◽  
Substrate Structure ◽  
Energy Inputs

Stellite 6 was deposited by laser cladding on a 9Cr-1Mo (P91) substrate with energy inputs of 1 kW (P91-1) and 1.8 kW (P91-1.8). The chemical compositions, microstructures and surface roughnesses of these coatings were characterized by atomic absorption spectroscopy, optical microscopy, scanning electron microscopy and atomic force microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was evaluated using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the 9Cr-1Mo (P91) steel substrate with the lower heat input (P91-1). Further, the Stellite coating for P91-1 was significantly harder than that obtained for P91-1.8. The wear test results indicated that the weight loss for P91-1 was much lower than for P91-1.8. The surface topography data indicated that the surface roughness for P91-1 was much lower than for P91-1.8. It is concluded that the lower hardness of the coating for P91-1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

Wear and Corrosion Behaviours of FeCrNiSi Alloy Coatings by Laser Cladding

2017 ◽  
Vol 898 ◽  
pp. 1406-1413
Author(s):  
Yu Long Qi ◽  
Hai Yan Chen ◽  
Chen Yang Shu ◽  
Xuan Zhao ◽  
Li Hua Dong ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Abrasive Wear ◽  
Laser Cladding ◽  
Wear Behavior ◽  
Testing Machine ◽  
Three Dimensional ◽  
Xrd Analysis ◽  
Hard Coating ◽  
Wear Testing ◽  
Surface Mapping

Soft and hard FeCrNiSi alloy coatings were obtained on 30CrMo alloy steel surface by laser cladding. The phase constitution, microstructure, frictional wear behavior and corrosion resistance of the composite coating were analyzed using X-ray diffraction (XRD), scanning electron microscope (SEM), three-dimensional non-contact surface mapping, friction and wear testing machine and electrochemical workstation, separately. XRD analysis showed that the cladding layer was mainly composed of Fe-based alloy composition, accompanied by a small amount of cobalt nickel alloy. There were massive protrusions in the interface of the soft sample, and the coating was regularly dendritic. Hard sample coating lines were cluttered, and there was no bulk deposition. Under the same wear condition, the soft coating exhibited serious abrasive wear, while the hard coating had slight abrasive wear behavior. The polarization curves in 3%NaCl solution revealed that the self-corrosion potential of the soft coating was positive shifted more than that the hard coating. The soft coating has better corrosion resistance than the hard coating.

Investigation on High-Phosphorus Electroless Ni–P Plating Technology of Stainless Steel

2011 ◽  
Vol 291-294 ◽  
pp. 129-132
Author(s):  
Xiao Juan Wu ◽  
Zheng Jun Liu ◽  
Guo De Li
Keyword(s):  
Stainless Steel ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Loss ◽  
Thermal Shock Test ◽  
Micro Hardness ◽  
Coating Quality ◽  
Technical Parameters ◽  
High Phosphorus ◽  
Electroless Ni

The high-phosphorus electroless Ni–P plating was coated on the surface of stainless steel. Five parameters, which have much effect on coating quality, were chosen to optimize the high-phosphorus electroless Ni–P plating technology in L16(45) orthogonal test. By means of x-ray diffraction and scanning electron microscopy, the morphologies and phase structures of coating were analyzed. Furthermore, the mechanical properties of coating were studied by micro-hardness tester and universal friction-wear testing machine. The results reveal that the optimal technical parameters are as follows: 20 g•L-1 for NiSO4, 23 g•L-1 for NaH2PO2, 15 g•L-1 for C6H5O7Na3•2H2O, 8 g•L-1 for H2N-CH2-COOH, 10g•L-1 for CH3COONa, 7 g•L-1 for C4H6O4, with PH value of 4.6, which leads to perfect coating quality. Besides, the P content is 11.64 wt.%, i.e. a high-P coating. The micro-hardness of the coating is 550.67 HV and the wear loss, 4.7×10-3 g. The thermal shock test suggests that between coating and matrix exist a perfect cohesion, which is due to the homogenous and compact coating, with an amorphous structure, under the condition of the optimal technical parameters.

Wear resistance of maraging steel developed by direct metal laser sintering

2020 ◽  
Vol 10 (7) ◽  
pp. 1079-1090 ◽  
Author(s):  
Gulam Mohammed Sayeed Ahmed ◽  
Irfan Anjum Badruddin ◽  
Vineet Tirth ◽  
Ali Algahtani ◽  
Mohammed Azam Ali
Keyword(s):  
Wear Resistance ◽  
Wear Rate ◽  
Maraging Steel ◽  
Normal Load ◽  
Testing Machine ◽  
Wear Test ◽  
Laser Sintering ◽  
Wear Testing ◽  
Direct Metal Laser Sintering ◽  
Wear Tests

This work presents wear study on maraging steel developed by additive manufacturing using Direct Metal Laser Sintering, utilizing a laser beam of high-power density for melting and fusing the metallic powders. Short aging treatment was given to the specimen prior to the wear tests. The density and the hardness of the 3D printed maraging steel were found to be better than the homogenized-aged 18Ni1900 maraging steel. The wear resistance is an important aspect that influences the functionality of the components. The wear tests in dry condition were performed on maraging steel on pin/disc standard wear testing machine. The design of experiments was planned and executed based on response surface methodology. This technique is employed to investigate three influencing and controlling constraints namely speed, load, and distance of sliding. It has been observed that sliding speed and normal load significantly affects the wear of the specimen. The statistical optimization confirms that the normal load, sliding distance, and speed are significant for reducing the wear rate. The confirmation test was conducted with a 95% confidence interval using optimal parameters for validation of wear test results. A mathematical model was developed to estimate the wear rate. The experimental results were matched with the projected values. The wear test parameters for minimum and maximum wear rate have been determined.

Sign in / Sign up

Export Citation Format

Share Document