A Processing Approach Incorporating Copper Backing-Wheel Device in Submerged Arc Welding for Manufacturing Cryogenic Storage Tanks

2014 ◽  
Vol 705 ◽  
pp. 106-111
Author(s):  
Supphachan Rajsiri ◽  
Mayuree Chomjanngam ◽  
Sittiphun Tuntawiroon
Keyword(s):  
Arc Welding ◽  
Submerged Arc Welding ◽  
Storage Tanks ◽  
Welding Temperature ◽  
New Approach ◽  
Cryogenic Storage ◽  
Processing Approach ◽  
Flux Cored Arc Welding ◽  
Welding Processes ◽  
Submerged Arc

A processing approach using a copper backing-wheel device was developed to aid the fabrication process of industrial cryogenic storage tanks manufactured under the ASME Section VIII Division 1. This research focused on the welding processes related to the cylindrical-body assembly. Two processing steps involving the root-run formation and the replacement with a sound outer-circumference joint were studied. Initially, tank fabrication is achieved through the application of both flux-cored arc welding and submerged arc welding. A new processing approach was proposed with the modified method in cross-section preparation, and a low-cost reusable copper backing-wheel device was developed to facilitate the root-run formation using only submerged arc welding. Temperature gradient through the device components along the heat-conduction path was monitored to assure the conductivity of the backing device. The results suggest that the proposed approach reduced manufacturing time by removing the initial flux-cored arc welding process used in the conventional welding method. As an effect, the new approach show promise reduces the overall manufacturing cost of tank fabrication. Based on radiographic testing of tanks fabricated using the new approach found that circumference joints required little or no welding repair suggesting higher joint quality.

Advanced submerged arc welding processes for Arctic structures and ice-going vessels

2016 ◽  
Vol 232 (1) ◽  
pp. 114-127
Author(s):  
Pavel Layus ◽  
Paul Kah ◽  
Viktor Gezha
Keyword(s):  
Case Studies ◽  
Arc Welding ◽  
Oil And Gas ◽  
Welding Process ◽  
Submerged Arc Welding ◽  
The Arctic ◽  
Correct Selection ◽  
Advantages And Disadvantages ◽  
Welding Processes ◽  
Submerged Arc

The Arctic region is expected to play an extremely prominent role in the future of the oil and gas industry as growing demand for natural resources leads to greater exploitation of a region that holds about 25% of the world’s oil and gas reserves. It has become clear that ensuring the necessary reliability of Arctic industrial structures is highly dependent on the welding processes used and the materials employed. The main challenge for welding in Arctic conditions is prevention of the formation of brittle fractures in the weld and base material. One mitigating solution to obtain sufficiently low-transition temperatures of the weld is use of a suitable welding process with properly selected parameters. This work provides a comprehensive review with experimental study of modified submerged arc welding processes used for Arctic applications, such as narrow gap welding, multi-wire welding, and welding with metal powder additions. Case studies covered in this article describe welding of Arctic steels such as X70 12.7-mm plate by multi-wire welding technique. Advanced submerged arc welding processes are compared in terms of deposition rate and welding process operational parameters, and the advantages and disadvantages of each process with respect to low-temperature environment applications are listed. This article contributes to the field by presenting a comprehensive state-of-the-art review and case studies of the most common submerged arc welding high deposition modifications. Each modification is reviewed in detail, facilitating understanding and assisting in correct selection of appropriate welding processes and process parameters.

New submerged arc welding flux for hardfacing of Hardox steels

2020 ◽  
Vol 62 (10) ◽  
pp. 1010-1016
Author(s):  
Mustafa Kaptanoglu ◽  
Akin Odabasi
Keyword(s):  
Welding Speed ◽  
Arc Welding ◽  
Experimental Studies ◽  
Submerged Arc Welding ◽  
Wear Properties ◽  
Welding Flux ◽  
Welding Processes ◽  
Hardness Values ◽  
Submerged Arc ◽  
Wear Tests

Abstract In this study, the usability of a new submerged arc welding flux was investigated to develop the surface properties of Hardox steels. In the hardfacing welding processes for Hardox 400 steel, four welding speeds resulting in varied heat inputs were applied. Through an analysis of the chemical composition, microstructure examinations, hardness measurements and wear tests, the possibility of hardfacing properties control due to the change of process parameters were determined. In the experimental studies, the hardness of the hardfacing obtained at a welding speed of 30 cm × min-1 was measured as 42 HRC while the hardness of the hardfacing obtained at a welding speed of 48 cm × min-1 was measured as 57 HRC. Moreover, in the wear tests, results consistent with the hardness values were obtained. It was understood in the light of the results that the use of high carbon ferro-chromium 20 wt.-% in a submerged arc welding flux mixture may be useful in improving hardness and wear properties of Hardox steels through hardfacing welding processes.

Development of Welding Procedures for X90-Grade Seamless Pipes for Riser Applications

2012 ◽  
Author(s):  
Hiroyuki Nagayama ◽  
Masahiko Hamada ◽  
Mark F. Mruczek ◽  
Mark Vickers ◽  
Nobuyuki Hisamune ◽  
...  
Keyword(s):  
Weld Metal ◽  
Arc Welding ◽  
Mechanical Test ◽  
Welding Process ◽  
High Strength ◽  
Submerged Arc Welding ◽  
Welding Parameters ◽  
Flux Cored Arc Welding ◽  
Welding Procedure ◽  
Submerged Arc

Ultra-high strength seamless pipes of X90 and X100 grades have been developed for deepwater or ultra-deepwater applications. Girth welding procedure specifications (WPSs) should be developed for the ultra-high strength pipes. However, there is little information for double jointing welding procedure by using submerged arc welding process for high strength line pipes. This paper describes mechanical test results of submerged arc welding (SAW) and gas shielded flux cored arc welding (GSFCAW) trials with various welding consumables procured from commercial markets. Welds were then made with typical welding parameters for riser productions using high strength X90 seamless pipes. The submerged arc weld metal strength could increase by increasing alloy elements in weld metal. The weld metal with CE (IIW) value of 0.74 mass% achieved fully overmatching for the X90 pipe. The weld metal yield strength (0.2% offset) was 694 MPa, and the ultimate tensile strength was 833 MPa. It was also confirmed that the reduction of boron in weld metal can improve low temperature toughness of high strength weld metal. Furthermore, it was confirmed that the HAZ has excellent mechanical properties and toughness for riser applications. In this study GSFCAW procedures were also developed. GSFCAW can be used for joining pipe and connector material for riser production welding. The weld metal with a CE (IIW) value of 0.54 mass% could meet the required strength level for X90-grade pipe as specified in ISO 3183. Cross weld tensile testing showed that fractures were achieved in the base metal. Good Charpy impact properties in weld metal and HAZ were also confirmed.

Numerical Analysis of Microstructure and Residual Stress in the Weld Zone of Multiwire Submerged Arc Welding

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Enlin Yu ◽  
Yi Han ◽  
Haixiang Xiao ◽  
Ying Gao
Keyword(s):  
Residual Stress ◽  
Temperature Measurement ◽  
Arc Welding ◽  
Large Diameter ◽  
Weld Zone ◽  
Submerged Arc Welding ◽  
Welding Parameters ◽  
Welding Quality ◽  
Welding Temperature ◽  
Submerged Arc

As oil and gas pipelines develop toward large throughput and high pressure, more and more attention has been paid to welding quality of oil pipelines. Submerged arc welding is widely applied in manufacturing of large-diameter welded pipes, and the welding quality has an impact on pipeline safety. With a multiwire submerged arc welding test platform and real-time temperature measurement system, temperature measurement has been done for multiwire submerged arc welding process with and without flux coverage, respectively. As a result, thermal cycling curves in both cases have been obtained, and convection and radiation coefficients of flux-covered X80 pipeline steel in air-cooled environment have been corrected. By using sysweld software, a finite-element computational model was set up for microstructure and residual stress in the weld zone of multiwire longitudinal submerged arc welding. Comparative experiment has been done to obtain welding temperature field with relatively high accuracy. Calculation and analysis of residual stress versus preheat residual stress decreased with increasing preheat temperature up to 100 °C, meanwhile content of bainite in microstructure fell, facilitating reduction in residual stress to some extent. This study provides quantitative reference for further optimization of welding parameters and improvement in weld mechanical properties.

scholarly journals The Effect of Welding Conditions on Mechanical Properties of Superduplex Stainless Steel Welded Joints

2014 ◽  
Vol 14 (1) ◽  
pp. 14-23 ◽  
Author(s):  
A. Świerczyńska ◽  
J. Łabanowski ◽  
D. Fydrych
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
Arc Welding ◽  
Submerged Arc Welding ◽  
Flux Cored Arc Welding ◽  
Superduplex Stainless Steel ◽  
Zone Microstructure ◽  
Submerged Arc

ABSTRACT The tests results of superduplex stainless steel welded joints made with a different heat input, using automatic submerged arc welding (SAW) and semi-automatic flux-cored arc welding (FCAW) have been presented. Metallographic examinations, the measurements of the ferrite content, the width of the heat affected zone (HAZ) and the hardness of the welds in characteristic areas have been performed. Significant differences in the amount of ferrite in the weld metal and in the heat affected zone microstructure of joints were found.

Effect of Welding Parameters on Temperature Field during Twin-Wire Submerged Arc Welding of X80 Pipeline Steel

2013 ◽  
Vol 652-654 ◽  
pp. 2347-2351
Author(s):  
Chun Yan Yan ◽  
Xin Zhao ◽  
Song Ya Tian ◽  
Sheng Xun Xu ◽  
Bai Qing Ma ◽  
...  
Keyword(s):  
Temperature Field ◽  
Temperature Distribution ◽  
Welding Speed ◽  
Arc Welding ◽  
Pipeline Steel ◽  
Submerged Arc Welding ◽  
Welding Parameters ◽  
X80 Pipeline Steel ◽  
Welding Temperature ◽  
Submerged Arc

The welding temperature field of twin-wire submerged arc welding (SAW) in an X80 pipeline steel welded joint was analyzed using a three-dimensional (3D) finite element (FE) model. Taking into account nonlinear relationships between temperature and mechanical properties, a coupled thermo-mechanical FE solution was used to obtain the temperature distribution for varying set of welding conditions. Effect of welding speed, inter wire spacing on welding temperature field were studied and presented. It is found that welding speed and inter wire spacing play a significant role in deciding the temperature distribution of twin-wire submerged arc welding. Simulation results were well consistent with theoretical analysis.

Sign in / Sign up

Export Citation Format

Share Document