Microstructure and Mechanical Properties of TiB-Ti/Ti-6Al-4V Composites Fabricated by Spark Plasma Sintering

2015 ◽  
Vol 782 ◽  
pp. 107-112
Author(s):  
Li Fen Wang ◽  
Zhao Hui Zhang ◽  
Tie Jian Su ◽  
Fu Chi Wang
Keyword(s):  
Mechanical Properties ◽  
Relative Density ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Fracture Strength ◽  
Sintering Temperature ◽  
Composite Layer ◽  
Micro Hardness ◽  
Plasma Sintering ◽  
Spark Plasma

TiB-Ti/Ti-6Al-4V composites were fabricated by spark plasma sintering (SPS) technique under a pressure of 50MPa, with sintering temperature of 1300 °C and heating rate of 100 °C /min. The effect of the TiB content in TiB-Ti composite layer on microstructures and mechanical properties of the TiB-Ti/Ti-6Al-4V composites were investigated. The results indicate that as an advanced welding method, SPS technique provided the excellent welding combination of TiB-Ti and Ti-6Al-4V. The relatively excellent mechanical properties of the joints, including the relative density of 98.6%, micro-hardness of 10.2GPa, fracture strength of 177MPa were achieved as TiB content in TiB-Ti composite layer reaches 50%.

Microstructure and Mechanical Properties of Spark-Plasma-Sintered SiC-TiC Composites

2005 ◽  
Vol 287 ◽  
pp. 335-339 ◽  
Author(s):  
Kyeong Sik Cho ◽  
Kwang Soon Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Applied Pressure ◽  
Argon Atmosphere ◽  
Full Density ◽  
Plasma Sintering ◽  
Spark Plasma

Rapid densification of the SiC-10, 20, 30, 40wt% TiC powder with Al, B and C additives was carried out by spark plasma sintering (SPS). In the present SPS process, the heating rate and applied pressure were kept at 100°C/min and at 40 MPa, while the sintering temperature varied from 1600-1800°C in an argon atmosphere. The full density of SiC-TiC composites was achieved at a temperature above 1800°C by spark plasma sintering. The 3C phase of SiC in the composites was transformed to 6H and 4H by increasing the process temperature and the TiC content. By tailoring the microstructure of the spark-plasma-sintered SiC-TiC composites, their toughness could be maintained without a notable reduction in strength. The strength of 720 MPa and the fracture toughness of 6.3 MPa·m1/2 were obtained in the SiC-40wt% TiC composite prepared at 1800°C for 20 min.

Preparation and Properties of ZrB2-Cu Composites by Spark Plasma Sintering

2012 ◽  
Vol 512-515 ◽  
pp. 739-743 ◽  
Author(s):  
S.Z. Zhu ◽  
D.L. Gong ◽  
Z. Fang ◽  
Q. Xu
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Volume Fraction ◽  
Sintering Temperature ◽  
High Electrical Conductivity ◽  
Particulate Reinforcement ◽  
Plasma Sintering ◽  
Spark Plasma

For high thermal conductivity and high electrical conductivity, copper is a good electrode material. The wearing resistance and spark resistance of Cu can be improved with the addition of ZrB2. ZrB2-Cu composites with high Cu volume fraction was successfully prepared by spark plasma sintering (SPS) process in this paper. The microstructure and properties of the sintered samples were characterized. The effect of the sintering temperature and the ZrB2 content in composites on the relative density and properties of the composites were investigated. The results show that the relative density and mechanical properties increase with the sintering temperature increasing. The optimum sintering temperature is 900 °C for 10wt.% ZrB2-Cu, 1000 °C for 20wt.% ZrB2-Cu and 1050 °C for 30wt.% ZrB2-Cu. With the ZrB2 content in composites increasing from 10wt.% to 30 wt.%, the electrical resistivity increases from 2.25×10-6 Ω.cm to 8.82×10-6 Ω.cm, the flexural strength decreases from to 539.1 MPa to 482.2 MPa and the fracture toughness decreases from to 15 MPa.m 1/2 to 9 MPa.m 1/2. The hardness (HV) of ZrB2-Cu composites is significantly enhanced by the ZrB2 particulate reinforcement, increasing from 1410 MPa for 10 wt.% ZrB2 to 2480 MPa for 30wt.% ZrB2.

Synthesis, Microstructure and Mechanical Properties of ZrB2 Ceramic Prepared by Mechanical Alloying and Spark Plasma Sintering

2010 ◽  
Vol 434-435 ◽  
pp. 165-168 ◽  
Author(s):  
Chun Feng Hu ◽  
Yoshio Sakka ◽  
Tetsuo Uchikoshi ◽  
Tohru Suzuki ◽  
Byung Koog Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Mechanical Alloying ◽  
Relative Density ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Vickers Hardness ◽  
Heating Rates ◽  
Plasma Sintering ◽  
Spark Plasma

Dense bulk ZrB2 ceramic was synthesized by mechanical alloying (MA) and followed spark plasma sintering (SPS) using zirconium and boron as initial materials. It was found that MA process was effective to fragment the coarse metal zirconium particles from 45 m to less than 1 m within 20 hours. In comparison with the commercial ZrB2 powder, the as-obtained zirconium and boron mixture powders showed higher sinterability. When the sintering was carried out at 1800oC, the relative density of synthesized ZrB2 samples using mixture powder was above 95%, higher than that of ZrB2 sample prepared using commercial powder (73%). Vickers hardness of those ZrB2 samples was at the same level of 15 GPa. However, the fracture toughness of ZrB2 samples seemed to depend on the heating rate of the SPS process. Corresponding to the heating rates of 10, 50, and 100oC/min, the fracture toughness of as-prepared ZrB2 samples were 3.83, 3.19, and 2.74 MPa•m1/2, respectively.

Sintering Performance and Mechanical Properties of Titanium Compacts Prepared by Spark Plasma Sintering

2012 ◽  
Vol 706-709 ◽  
pp. 217-221 ◽  
Author(s):  
Hiroshi Izui ◽  
Genki Kikuchi
Keyword(s):  
Mechanical Properties ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Tensile Property ◽  
Density Ratio ◽  
Alloying Elements ◽  
Blended Elemental ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Stabilizing Element

Titanium alloys were produced by blended elemental powder metallurgy (P/M) method. We focused on the effect of alloying elements (Fe, Mo, and Al) on the consolidation and mechanical properties of Ti compacts prepared by spark plasma sintering. The effects of amount of alloying elements and sintering temperature on the relative density and tensile properties of Ti compacts were investigated. The addition of β-stabilizing elements (Fe and Mo) significantly improved the densification of Ti compacts, where the relative density ratio of Ti-5 wt% Mo specimen became higher than 99.9 %, and Ti-5 wt% Fe specimen higher than 99.0 %. On the other hand, the addition of Al as α-stabilizing element led to improve the relative density of Ti-5 wt% Al compact with higher than 99.9 %. The tensile property for sintered Ti-5 wt% Mo compact had the highest elongation of 16 %. It will be discussed the microstructures and tensile property of the compacts.

scholarly journals Characterization of Multiwalled Carbon Nanotube-Reinforced Hydroxyapatite Composites Consolidated by Spark Plasma Sintering

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Duk-Yeon Kim ◽  
Young-Hwan Han ◽  
Jun Hee Lee ◽  
Inn-Kyu Kang ◽  
Byung-Koog Jang ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Relative Density ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Multiwalled Carbon Nanotube ◽  
Multiwalled Carbon ◽  
Pull Out ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Mwnt Content

Pure HA and 1, 3, 5, and 10 vol% multiwalled carbon nanotube- (MWNT-) reinforced hydroxyapatite (HA) were consolidated using a spark plasma sintering (SPS) technique. The relative density of pure HA increased with increasing sintering temperature, but that of the MWNT/HA composite reached almost full density at 900°C, and then decreased with further increases in sintering temperature. The relative density of the MWNT/HA composites increased with increasing MWNT content due to the excellent thermal conductivity of MWNTs. The grain size of MWNT/HA composites decreased with increasing MWNT content and increased with increasing sintering temperature. Pull-out toughening of the MWNTs of the MWNT/HA composites was observed in the fractured surface, which can be used to predict the improvement of the mechanical properties. On the other hand, the existence of undispersed or agglomerate MWNTs in the MWNT/HA composites accompanied large pores. The formation of large pores increased with increasing sintering temperature and MWNT content. The addition of MWNT in HA increased the hardness and fracture toughness by approximately 3~4 times, despite the presence of large pores produced by un-dispersed MWNTs. This provides strong evidence as to why the MWNTs are good candidates as reinforcements for strengthening the ceramic matrix. The MWNT/HA composites did not decompose during SPS sintering. The MWNT-reinforced HA composites were non-toxic and showed a good cell affinity and morphologyin vitrofor 1 day.

Fabrication of High Dense ZnSe Ceramic by Spark Plasma Sintering: The Effect of the Powder Process Method

2018 ◽  
Vol 281 ◽  
pp. 661-666
Author(s):  
Jia Lin Gao ◽  
Peng Liu ◽  
Jian Zhang ◽  
Xiao Dong Xu ◽  
Ding Yuan Tang
Keyword(s):  
Relative Density ◽  
Ball Milling ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Zinc Selenide ◽  
Plasma Sintering ◽  
Planetary Ball Milling ◽  
Spark Plasma ◽  
Process Method

Zinc Selenide ceramic was successfully fabricated by spark plasma sintering in the study. The ZnSe raw powders were handled with two different methods such as grinding and planetary ball milling, respectively. The relative density, microstructure and transmittance of the ZnSe ceramic sintered under the same sintering parameter with two type powders was investigated. The results shown that the performance of the powder processed by ball milling was more effective than that by grinding. Furthermore, the maximum relative density can reach 99.8% when the ZnSe powder treated by ball milling were sintered at 950 oC for 30 min with the heating rate of 10 oC/min under 100 MPa.

Fabrication of MgO/Graphene Composites by Combustion Synthesis and Spark Plasma Sintering

2018 ◽  
Vol 281 ◽  
pp. 125-130
Author(s):  
Nan Lu ◽  
Jia Xi Liu ◽  
Gang He ◽  
Jiang Tao Li
Keyword(s):  
Mechanical Properties ◽  
Combustion Synthesis ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
Combustion Reaction ◽  
Sintering Additive ◽  
Microstructure And Mechanical Properties ◽  
Plasma Sintering ◽  
Spark Plasma

MgO/Graphene ceramic composites were fabricated by combining combustion synthesis with spark plasma sintering. MgO/Graphene mixture powders were prepared by the combustion reaction between Mg powders and CO2 gas. Dense MgO/Graphene composites were fabricated by spark plasma sintering (SPS) using LiF as the sintering additive. The effect of the sintering temperature on microstructure and mechanical properties of the prepared MgO/Graphene ceramics was discussed. The sintering temperature of the MgO/Graphene mixture powders increased from 900°C to 1300°C. The highest density of 3.43g/cm3 and hardness of 2133MPa were obtained at 1100°C. Compared with monolithic MgO ceramics, the hardness of MgO/Graphene ceramics at the same sintering temperature was increased from 840MPa to 2133MPa.

Sign in / Sign up

Export Citation Format

Share Document