The Energy-Saving and Carbon Emission Analysis of Solar-Assisted Air Source Heat Pump System for Hot Water Supply

2015 ◽  
Vol 799-800 ◽  
pp. 1440-1444
Author(s):  
Yuan Yu ◽  
Ke Zhi Yu ◽  
Hai Zhang
Keyword(s):  
Energy Consumption ◽  
Carbon Emission ◽  
Operating Cost ◽  
Heating System ◽  
High Energy ◽  
Hot Water ◽  
Cost Comparison ◽  
Water Heating ◽  
Emission Analysis ◽  
Pump System

The innovation of solar water heating system of students living community in Shanghai Ocean University is illustrated in this paper. A new water heating system including solar, air source heat pumps and gas boiler is established owing to the high energy consumption of original system. The comprehensive energy consumption, carbon emission and operating cost comparison between the original and new system is analysed based on the measured water, power and natural gas consumption. The results show that the comprehensive energy consumption is reduced by about 27.5%, the carbon commission decreased by 6%, and the operating costs reduced by approximately 23.6%, which means the new hot water system is successful.

Research on Composite System of Solar Energy Reclaimed Water Heat Pump and Phase Change Energy Storage

2014 ◽  
Vol 521 ◽  
pp. 56-59
Author(s):  
Hui Xing Li ◽  
Peng Cheng ◽  
Guo Hui Feng ◽  
Ran Zhang
Keyword(s):  
Heat Pump ◽  
Operating Cost ◽  
Reclaimed Water ◽  
Water Source ◽  
Heating System ◽  
Hot Water ◽  
Water Heating ◽  
Pump System ◽  
Heat Pump System ◽  
Important Approach

New energy development and utilization is an important approach to solve the problem of energy shortage,a new type of composite heating system is proposed in this study. It expounds the research ideas, the technical principle and operation plan of the system. Through a comparative analysis of the performance coefficient of composite heating system, reclaimed water source heat pump system and solar hot water heating system, it Comes to the conclusions that the composite heating system can not only reduce the operating cost but also improve the running performance of reclaimed water source heat pump and reduce the heat loss of solar hot water heating system.

Energy Consumption Modeling of a Heat Pump System for Combined Space Conditioning and Residential Water Heating in a Typical Household in Quito, Ecuador

2016 ◽  
Author(s):  
Gabriel Agila ◽  
Guillermo Soriano
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Thermal Storage ◽  
Hot Water ◽  
Water Heating ◽  
Water Heater ◽  
Pump System ◽  
Detailed Model ◽  
Heat Pump Water Heater ◽  
Residential Water

This research develops a detailed model for a Water to Water Heat Pump Water Heater (HPWH), operating for heating and cooling simultaneously, using two water storage tanks as thermal deposits. The primary function of the system is to produce useful heat for domestic hot water services according to the thermal requirements for an average household (two adults and one child) in the city of Quito, Ecuador. The purpose of the project is to analyze the technical and economic feasibility of implementing thermal storage and heat pump technology to provide efficient thermal services and reduce energy consumption; as well as environmental impacts associated with conventional systems for residential water heating. An energy simulation using TRNSYS 17 is carried to evaluate model operation for one year. The purpose of the simulation is to assess and quantifies the performance, energy consumption and potential savings of integrating heat pump systems with thermal energy storage technology, as well as determines the main parameter affecting the efficiency of the system. Finally, a comparative analysis based on annual energy consumption for different ways to produce hot water is conducted. Five alternatives were examined: (1) electric storage water heater; (2) gas fired water heater; (3) solar water heater; (4) air source heat pump water heater; and (5) a heat pump water heater integrated with thermal storage.

Optimization for Heating System Schemes Based on GRA Method

2008 ◽  
Author(s):  
Wei Bing ◽  
Li Li
Keyword(s):  
Power System ◽  
Operating Cost ◽  
Heating System ◽  
Social Benefit ◽  
High Energy ◽  
Pump System ◽  
Heat Pump System ◽  
Decision Making Problem ◽  
Calculation Results ◽  
Optimal Heating

In China, the overall economical performances of heating systems are not very high, there are still some problems of high energy consumption, high gas emission and low heat utilization. The energy conversation and emission reduction are two most important things. The option of the heating system schemes is the key to improve such situation. An optimal heating scheme will be a good beginning to the whole heating system. In this paper, the GRA (Grey Relation Analysis) method is introduced and used, and with the example of a heating district, the most used and upcoming used heating schemes are listed, calculated and compared by using the method of GRA. The option of a heating system scheme is a typical multi-objective decision-making problem. The schemes are the district boiler heating system (including gas-fired, oil-fired, and coal-fired boilers), solar energy heat pump system and combined heating and power system etc. In the process of optimization calculation, the aspects of energy saving, economics benefit, environment benefit and social benefit are concerned about, and the initial cost, operating cost, employment life, environment influence and system reliability are taken into account. According to the calculation results, combined heating and power system is proposed to be optimal heating system scheme.

scholarly journals Thermal Comfort Analysis of Combined Radiation-Convection Floor Heating System

Energies ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1420 ◽  
Author(s):  
Beungyong Park ◽  
Seong Ryong Ryu ◽  
Chang Heon Cheong
Keyword(s):  
Energy Consumption ◽  
Thermal Performance ◽  
Thermal Environment ◽  
Heating System ◽  
Hot Water ◽  
Pump System ◽  
Heat Pump System ◽  
Convection Heating ◽  
The Difference ◽  
Floor Heating

In this paper, a novel combined radiation-convection floor heating system is shown. This study uses practice-based learning and investigated the thermal performance of a combined radiation-convection floor heating system with a water heat pump system by evaluating the thermal environment and energy consumption in an experimental test. A new method that analyzed the thermal performance of four different controls was developed and applied. The results of the surface temperature distributions demonstrated that Mode 1, which uses only convection, had the lowest floor temperature and was thus considered inappropriate for occupants who sleep on the floor. By contrast, Modes 2, 3, and 4 showed high floor surface temperatures as hot water was supplied to the radiant heating panel. The predicted mean vote (PMV) results suggest that radiant floor heating is not appropriate for intermittent heating. In other words, occupants of single residences who return home at night will experience a long period of discomfort if they heat their room using floor heating. In this case, Mode 1, which is convection heating, and Modes 3 and 4, which represent mixed modes provide a more comfortable environment. The difference between this experimental study and previous research is that four different control modes for a combined radiation-convection system were evaluated based on the same location of the equipment in a laboratory. Furthermore, we studied the long-term real-scale thermal performance using panel and energy consumption.

scholarly journals Energy Efficient Approaches by Retrofitting Heat Pumps Water Heating System for a University Dormitory

Buildings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 356
Author(s):  
Fujen Wang ◽  
Kusnandar ◽  
Hungwen Lin ◽  
Minghua Tsai
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Heat Pump ◽  
Energy Efficient ◽  
Energy Savings ◽  
Heating System ◽  
Energy Simulation ◽  
Water Heating ◽  
Pump System ◽  
Heat Pump System

With the cost of energy rising, the value of conservation grows. Interest in energy efficiency could be a sound investment or a necessary public policy. Heat pump systems provide economical alternatives of recovering heat from different sources for use in various applications. The objective of this study is to present the strategic approach on the energy efficient analysis of the water heating system retrofitted by applying a heat pump system in the dormitory of a university. Energy savings were determined by comparing field measurements of water consumption, water temperature and power consumption of the overall system before (electric resistance heating system) and after (heat pump heating system) the implementation of this project. Furthermore, the building energy simulation code (eQuest) has been applied to verify and predict the long-term energy consumption for both water heating systems. The results from energy modelling revealed the good agreement for energy simulation and field measurement data and the improvement of energy efficiency and energy savings could be achieved satisfactorily by retrofitting of a heat pump system. The energy conversion efficiency of hot water for energy consumption at 0.63 (Mcal/Mcal) could be achieved after the application of heat pump water heating system. It also presented the annual saving about USD 20,000 (NTD 600,000) for the dorm by using a heat pump heating system under the electrical billing rate of Taiwan.

Combined Space-Heating/Water-Heating System Performance

2001 ◽  
Author(s):  
Evelyn Baskin ◽  
John Spears
Keyword(s):  
Energy Use ◽  
Operating Cost ◽  
Heating System ◽  
Hot Water ◽  
Space Heating ◽  
Water Heating ◽  
Fuel Prices ◽  
Actual Usage ◽  
Heating Performance ◽  
One Year

Abstract With increasing fuel prices, various energy-saving techniques have been considered for residential appliances. Space heating accounts for the largest energy use in residential applications. One method proposed by manufacturers to keep operating cost low is to combine residential water-heating and space-heating functions into a single system. This paper presents the field test results of the performance of a combined water-heating/space-heating system under actual usage conditions. The system was installed in an 1187 ft2 (110 m2) home (Green Home) located in the Washington DC area. Data were collected for a one-year period. The water-heating performance was established by evaluating the hot water usage data during the test period. Water-heating/space-heating performance was established by using hot water data plus the amount of hot water circulated for space heating during the winter months. Analysis of the data indicated that the system produces hot water at an efficiency averaging 48% for water heating in the summer months and produces hot water at an efficiency ranging between 63.5–69.4% for combined water-heating/space-heating during the winter months. The relative humidity was maintained in the home at substantially lower level than that of the outside air, and the inside temperature was kept at the desired setting.

DETERMINING THE PROFITABILITY OF GREENHOUSE ELECTROTECHNOLOGIES: A MODELING APPROACH

HortScience ◽  
1994 ◽  
Vol 29 (4) ◽  
pp. 249a-249
Author(s):  
Eric A. Lavoie ◽  
Damien de Halleux ◽  
André Gosselin ◽  
Jean-Claude Dufour
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Water System ◽  
Heat Pumps ◽  
Hot Water ◽  
Pump System ◽  
Heat Pump System ◽  
Artificial Lighting ◽  
Hot Air ◽  
Marketable Fruit

The main objective of this research was to produce a simulated model that permitted the evaluation of operating costs of commercial greenhouse tomato growers with respect to heating methods (hot air, hot water, radiant and heat pumps) and the use of artificial lighting for 1991 and 1992. This research showed that the main factors that negatively influence profitability were energy consumption during cold periods and the price of tomatoes during the summer season. The conventional hot water system consumed less energy than the heat pump system and produced marketable fruit yields similar to those from the heat pump system. The hot water system was generally more profitable in regards to energy consumption and productivity. Moreover, investment costs were less; therefore, this system gives best overall financial savings. As for radiant and hot air systems, their overall financial status falls between that of the hot water system and the heat pump. The radiant system proved to be more energy efficient that the hot air system, but the latter produced a higher marketable fruit yield over the 2-year study.

scholarly journals Mitigating the Energy Consumption and the Carbon Emission in the Building Structures by Optimization of the Construction Processes

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3287
Author(s):  
Alireza Tabrizikahou ◽  
Piotr Nowotarski
Keyword(s):  
Life Cycle ◽  
Energy Consumption ◽  
Structural Optimization ◽  
Carbon Emissions ◽  
Carbon Emission ◽  
Construction Materials ◽  
High Energy ◽  
Building Structures ◽  
Life Cycle Stages ◽  
Reduction Of Energy Consumption

For decades, among other industries, the construction sector has accounted for high energy consumption and emissions. As the energy crisis and climate change have become a growing concern, mitigating energy usage is a significant issue. The operational and end of life phases are all included in the building life cycle stages. Although the operation stage accounts for more energy consumption with higher carbon emissions, the embodied stage occurs in a time-intensive manner. In this paper, an attempt has been made to review the existing methods, aiming to lower the consumption of energy and carbon emission in the construction buildings through optimizing the construction processes, especially with the lean construction approach. First, the energy consumption and emissions for primary construction materials and processes are introduced. It is followed by a review of the structural optimization and lean techniques that seek to improve the construction processes. Then, the influence of these methods on the reduction of energy consumption is discussed. Based on these methods, a general algorithm is proposed with the purpose of improving the construction processes’ performance. It includes structural optimization and lean and life cycle assessments, which are expected to influence the possible reduction of energy consumption and carbon emissions during the execution of construction works.

Energy Consumption Analysis of Animation-Park in Sino-Singapore Tianjin Eco-City

2013 ◽  
Vol 316-317 ◽  
pp. 176-180 ◽  
Author(s):  
Xue Jing Zheng ◽  
Meng Jun Yang ◽  
Wan Dong Zheng ◽  
Yun Kun Bu
Keyword(s):  
Renewable Energy ◽  
Energy Consumption ◽  
Water System ◽  
Energy System ◽  
Living Environment ◽  
Hot Water ◽  
Solar Pv ◽  
Pump System ◽  
Heat Pump System ◽  
Save Energy

Sino-Singapore Tianjin Eco-city is a strategic cooperation project between China and Singapore to improve the living environment and build an eco-culture. Animation-park covers an area of 1 km2, with a total construction area of 7.7x105m2. Wide sources of the renewable energy, such as solar hot water system, ground source heat pump system, solar PV power generation system, and deep geothermal energy system, is strongly recommended to use in eco-city in order to save energy and protect the environment. The usage of renewable energy is seen as a complement to the conventional energy. The energy consumption of the animation park is 42926tce of coal per year, and the renewable energy that used is 4573.6tce of coal per year. The usage of renewable energy leads to the reduction in the emission of CO2 of 18895.9t per year.

An Experimental Study of Different Thermal Boxes Heated by Solar Thermal Radiation for Hot Water System at Daytime

2013 ◽  
Vol 315 ◽  
pp. 783-787
Author(s):  
M.Yaakob Yuhazri ◽  
A.M. Kamarul ◽  
A.H. Rahimah ◽  
Sihombing Haeryip ◽  
S.H. Yahaya
Keyword(s):  
Energy Source ◽  
Water System ◽  
Heating System ◽  
Black Body ◽  
Hot Water ◽  
Experimental Result ◽  
Water Heating ◽  
Trapped Air ◽  
Current Water ◽  
Tropical Weather

This research is related to thermal efficient water heating system, specifically to improve the water heating system that exists nowadays. The goal of this research is to improve the current water heating system by using solar heat as the energy source to heat the water. The focus is to improve the thermal efficiency by adding different thermal boxes as the absorber bed. By implementing the black body and radiation concept, the air trapped in the box is heated. The trapped air then increases the collisions between the molecules and directly increases the temperature inside the box, higher than the outside environment. Based on a daytime experimental result revealed steel thermal box is better to be used for tropical weather like Malaysia.

Sign in / Sign up

Export Citation Format

Share Document