The Study of Nitrogen Absorption with Slagging in High Nitrogen Steels Smelted by High Pressure and Bottom-Blowing Nitrogen

2010 ◽  
Vol 146-147 ◽  
pp. 1120-1125 ◽  
Author(s):  
Yu Feng Guo ◽  
Shu Huan Wang ◽  
Gang Qiang Jin
Keyword(s):  
High Pressure ◽  
Nitrogen Content ◽  
Aluminum Content ◽  
Pure Aluminum ◽  
Slag System ◽  
Nitrogen Absorption ◽  
High Nitrogen ◽  
Nitrogen Steels ◽  
Bottom Blowing

The experiment studied the influence of slag system on nitrogen content in high nitrogen steels which refined by the method of high-pressure and bottom-blowing nitrogen under the conditions of 1.0Mpa. The results shows that nitrogen content are up to 1.0% without the over of slag, and after adding slag, nitrogen content are up to 1.39%; Alkalinity of protecting slag has little effect on the nitrogen content, however, there are very effective to increase nitrogen after using CaF2 instead of SiO2 ,and its nitrogen content are as high as 1.48%; the effect of increasing nitrogen are clear by adding no more than 0.5% pure aluminum, but when aluminum content are more than 0.5%, the nitrogen content in steel are not change significantly, meanwhile, if adding CaF2 slag system, it will be more effective increase nitrogen than only adding pure aluminum.

Comprehensive Analysis of High Nitrogen Steel Refining Factors with High-Pressure and Bottom-Blowing Nitrogen

2010 ◽  
Vol 146-147 ◽  
pp. 445-453
Author(s):  
Gang Qiang Jin ◽  
Shu Huan Wang ◽  
Yu Feng Guo ◽  
Xin Sheng Liu
Keyword(s):  
High Pressure ◽  
Nitrogen Content ◽  
High Nitrogen Steel ◽  
High Nitrogen ◽  
Thermodynamics And Kinetics ◽  
Nitrogen Steel ◽  
Surface Active ◽  
Steel Refining ◽  
Nitrogen Steels ◽  
Bottom Blowing

The experimental results on high nitrogen steels refining with high-pressure and bottom-blowing nitrogen were analyzed by the theories of thermodynamics and kinetics in high nitrogen steels smelting. It was shown that nitrogen content in steel increases with the increase of the following factors, that is, pressure, alloying elements (Cr and Mn), bottom-blowing time and bottom-blowing flow. While the nitrogen content in steel decreases with the temperature increase, but it is not obvious. The nitrogen content in steel can also increase with the surface active elements (O and S) decreasing.

Research on Effect of Temperature on Nitrogen Solubility in Steel

2011 ◽  
Vol 415-417 ◽  
pp. 915-919
Author(s):  
Shu Huan Wang ◽  
Cui Liang Wang ◽  
Ding Guo Zhao ◽  
Ju Gao
Keyword(s):  
High Pressure ◽  
Nitrogen Content ◽  
Stainless Steels ◽  
Nitrogen Solubility ◽  
Effect Of Temperature ◽  
High Nitrogen ◽  
Nitrogen Steels

The experiments of high nitrogen steels refining have been researched with high pressure and bottom-blown nitrogen in laboratory. We can gain high nitrogen nickel-free stainless steels that its content is more than 0.9%. The research indicates that the temperature influences nitrogen content greatly in the processes of smelting and concreting. The results are shown that saturated nitrogen content in steel increased slightly. When the temperature is as high as 1913K, the nitrogen content can reach 1.191%.

The Effect of Time to Nitrogen Solubility in Steel with High Pressure and Bottom Blowing Nitrogen

2011 ◽  
Vol 402 ◽  
pp. 202-204
Author(s):  
Ai Min Gao ◽  
Xin Kuo Fang ◽  
Shu Huan Wang
Keyword(s):  
High Pressure ◽  
Nitrogen Content ◽  
Alloy Steel ◽  
Atmospheric Pressure ◽  
Nitrogen Solubility ◽  
Solubility Limit ◽  
High Nitrogen Steel ◽  
High Nitrogen ◽  
Nitrogen Steel ◽  
Bottom Blowing

The high nitrogen steel is alloy steel whose nitrogen content is more than solubility limit at atmospheric pressure[1]. Bottom-blowing high-pressure nitrogen smelting nitrogen steel has many advantages, in the paper, from the study of 18Mn18CrN,it can come to a conclusion that in the case of Temperature of 1853K, pressure of 1.0MPa, the bottom-blowing flow of 0.16m3 / h and temperature of 1873K, pressure of 1.4MPa, the bottom-blowing flow of 0.16m3 / h, With the bottom-blowing time of increased the nitrogen content in steel increases, but when the time is more the 10 minutes, the nitrogen content is saturated.

Research on Nitrogen Control Technology of High-Pressure Bottle Steel

2014 ◽  
Vol 988 ◽  
pp. 177-182
Author(s):  
Chen Jun
Keyword(s):  
High Pressure ◽  
Nitrogen Content ◽  
Control Measures ◽  
Nitrogen Control ◽  
Nitrogen Absorption ◽  
High Nitrogen ◽  
Finished Steel ◽  
Casting Technology ◽  
Nitrogen Steel ◽  
Low Nitrogen

Nitrogen content of the high-pressure bottle steel was high and with big fluctuation, it is difficult to control. SO, investigation on nitrogen content of the all steelmaking process is carried out. Results of the investigation indicated that nitrogen content of the aimed steel was high, nitrogen absorption was mainly happened during tapping and in the course of after refining to before casting。And then nitrogen control measures such as low-nitrogen steel melting technology, optimization of deoxidization, protective casting technology is raised. After that nitrogen content of the aimed steel was reduced and nitrogen absorption during tapping and in the course of after refining to before casting was effectively controlled, nitrogen content of the finished steel was stably controlled in 50×10-6, the effect of nitrogen on property of steel is reduced.

The Study of Nitrogen Solubility in High Nitrogen Steels Smelted with High Pressure and Bottom-Blowing Nitrogen

2013 ◽  
Vol 634-638 ◽  
pp. 3170-3173
Author(s):  
Shu Huan Wang ◽  
Long Chen ◽  
Ding Guo Zhao ◽  
Chen Xiao Li ◽  
Yan Hui Wu
Keyword(s):  
High Pressure ◽  
Nitrogen Solubility ◽  
Nitrogen Atmosphere ◽  
Calculation Model ◽  
High Nitrogen ◽  
Nitrogen Steels ◽  
Bottom Blowing ◽  
High Pressure Reaction ◽  
Single Factor Experiment ◽  
Saturated Solubility

The experiments of smelting high nitrogen nickel-free stainless steel were carried out in the high temperature and high pressure reaction kettle. The nitrogen content was more than 1.36% by using the method of high pressure and bottom blowing nitrogen. With controlling high pressure nitrogen atmosphere and bottom blowing nitrogen, internal react were investigated by single factor experiment. Experimental results shown that there is saturated solubility, while smelting 18Mn18CrN steel with high pressure and bottom blowing nitrogen. Thermodynamic calculation model nitrogen solubility under the condition of high pressure was established, and the influence of nitrogen partial pressure on saturated solubility was researched.

Study on Effect of Pressure to Nitrogen Solubility Limit in High Nitrogen Steels

2011 ◽  
Vol 402 ◽  
pp. 169-172
Author(s):  
Shu Huan Wang ◽  
Chen Xiao Li ◽  
Xin Kuo Fang
Keyword(s):  
High Pressure ◽  
Stainless Steels ◽  
Main Part ◽  
Nitrogen Solubility ◽  
Solubility Limit ◽  
Single Factor ◽  
High Nitrogen ◽  
Nitrogen Steels ◽  
Bottom Blowing ◽  
Single Factor Experiment

This paper aims to study the effect of time and pressure on the nitrogen solubility limit through single factor experiment. The experiment is operated in the independent designed device whose main part is high temperature and high pressure reactor, Using high pressure and bottom blowing nitrogen in the furnace, it can gain high nitrogen nickel-free stainless steels whose nitrogen content is more than 1.1%.;The results show that there is solubility limit of nitrogen in 18Mn18CrN steel under certain condition ; The solubility limit of nitrogen in steel increases with the growth of pressure which ranges from 0.4MPa to 1.4MPa.

scholarly journals High Nitrogen Steels. Nitrogen Content of 316L Weld Metal and Its Fine Particle by Means of High-pressure MIG Arc Welding.

1996 ◽  
Vol 36 (7) ◽  
pp. 977-982 ◽  
Author(s):  
Yasushi Kikuchi ◽  
Fukuhisa Matsuda ◽  
Takatoshi Okabe ◽  
Makoto Ohta
Keyword(s):  
High Pressure ◽  
Weld Metal ◽  
Nitrogen Content ◽  
Arc Welding ◽  
Fine Particle ◽  
High Nitrogen ◽  
Nitrogen Steels

Applied Research of Smelting High Nitrogen Steels by Bottom-Blowing Nitrogen

2012 ◽  
Vol 236-237 ◽  
pp. 163-166
Author(s):  
Shu Huan Wang ◽  
Ding Guo Zhao ◽  
Xiao Jie Cui ◽  
Qiu Jing Li
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Experimental Research ◽  
Liquid Steel ◽  
Applied Research ◽  
High Nitrogen ◽  
Foreign Countries ◽  
Technical Effect ◽  
Nitrogen Steels ◽  
Bottom Blowing

The method of smelting High nitrogen steels by blowing nitrogen from the device bottom is a promising way of increasing nitrogen with gas. Introduced the device and technical development of smelting High nitrogen steels in domestic and foreign countries, expounded the method and character of dissolving nitrogen into liquid steel at high temperature and high pressure, and analyzed the advantage of increasing nitrogen by bottom-blowing nitrogen. The domestic research is at the developing period of experimental research. The High nitrogen steels which content is more than 1.0% was produced with bottom-blowing nitrogen method at high pressure. The velocity of dissolving nitrogen with bottom-blowing was increased and the smelting time was shortened. The technical effect was very good.

Research of Flow Simulation with High-Pressure and Bottom-Blowing Nitrogen

2013 ◽  
Vol 634-638 ◽  
pp. 3110-3113
Author(s):  
Shu Huan Wang ◽  
He Jun Zhang ◽  
Ding Guo Zhao
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Molten Steel ◽  
Gas Content ◽  
High Nitrogen Steel ◽  
High Nitrogen ◽  
Nitrogen Steel ◽  
Bottom Blowing ◽  
Steel Flow ◽  
Pressure Factor

According to the actual situation of refining high nitrogen steel with the laboratory high pressure reaction axe, the molten steel flow field in the high-pressure and bottom-blowing nitrogen reactor was simulated by using the software Fluent. The rules of the influence of pressure factor on the molten steel flow field characteristics, turbulent kinetic energy and gas content were explored. According to the characteristics of the flow field and gas-liquid two phase structure, the rules of the influence of pressure factor on nitrogen concentration distribution were analyzed. So some useful theoretical basis and guidance were provided for laboratory refining high nitrogen steel and industrial production in the future.

Dissolution and Precipitation of Excess Phases in High-Nitrogen Steels

2010 ◽  
Vol 638-642 ◽  
pp. 3026-3031 ◽  
Author(s):  
A.G. Svyazhin ◽  
Liudmila M. Kaputkina
Keyword(s):  
Nitrogen Content ◽  
Cooling Rate ◽  
Nitrogen Concentration ◽  
Dual Phase ◽  
High Nitrogen ◽  
Cooling Rates ◽  
Cast Structure ◽  
Nitrogen Steels ◽  
Excess Phases ◽  
Dissolution And Precipitation

Cast structure of ferric, austenitic and dual-phase high-nitrogen alloys and steels saturated with nitrogen at pressures of up to 3.2 MPa and solidified at cooling rates of 2 to 4•104 K/s has been investigated. Increasing the nitrogen concentration in the alloy and decreasing the cooling rate results in smaller nitrogen content in α and γ solutions and in larger content of crystallization nitrides.

Sign in / Sign up

Export Citation Format

Share Document