Microstructure and Mechanical Properties of Sn-Bi Alloy Treated in the Semi-Solid State by Mechanical Stirring Process

2010 ◽  
Vol 150-151 ◽  
pp. 1768-1771 ◽  
Author(s):  
Feng Li ◽  
Yong Jun Hu ◽  
Xiao Ling Cheng ◽  
Xiao Ting Xiao
Keyword(s):  
Mechanical Properties ◽  
Solid State ◽  
Die Casting ◽  
Percentage Elongation ◽  
Mechanical Stirring ◽  
Microstructure And Mechanical Properties ◽  
Stirring Time ◽  
Microstructures And Mechanical Properties ◽  
Semi Solid

In this work, the effect of stirring time on the solidifed microstructures and mechanical properties of semi-solid Sn-Bi slurry was investigated by the mechanical stirring method. The results indicated that a fine round granular solidifed structure of Sn-Bi semi-solid slurry was obtained at 142 and stirred for 8 min. Compared with the Sn-Bi alloy prepared conventional die casting, the mechamical properties of semi-solid Sn-Bi alloy was improved prominently. The percentage elongation of semi-solid Sn-Bi alloy was increased 67 % compared with that of the Sn-Bi alloy prepared conventional die casting.

The Influence of Stirring Time on Mechanical Properties of Sn–58Bi Alloy Treated in the Semi-Solid State by Mechanical Stirring Process

2011 ◽  
Vol 480-481 ◽  
pp. 1521-1524 ◽  
Author(s):  
Yong Jun Hu ◽  
Yong Li ◽  
Jian Nan He ◽  
Xiao Ling Cheng ◽  
Feng Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Die Casting ◽  
Solidification Process ◽  
Eutectic Structure ◽  
Lamellar Eutectic ◽  
Mechanical Stirring ◽  
Plate Shape ◽  
Stirring Time ◽  
Semi Solid ◽  
Lamellar Eutectic Structure

In this paper, the technology of semi-solid casting was to used are produced Sn-Bi alloy. The influence of agitating time at 125 °C on the microstructure and mechanical properties of of Sn-58Bi casting alloy were discussed. The eutectic Sn-Bi alloy was mechanically agitated during the casting solidification process. The results indicated that non-lamellar Sn-Bi structure with long plate shape, short strip, small size block and suborbicular block shape Sn phase was obtained for different stirring time. The elongation of Sn-Bi alloy with non-lamellar eutectic structure is improved prominently. Compared with the elongation of lamellar eutectic Sn-Bi alloy prepared by conventional die casting, the elongation of semi-solid Sn-Bi alloy with suborbicular block shape Sn phase is enhanced up to 45%.

Investigation of Microstructure and Mechanical Properties of Semi-Solid State Joining of SSM Aluminum Alloys

2014 ◽  
Vol 496-500 ◽  
pp. 371-375 ◽  
Author(s):  
Apirit Petkhwan ◽  
Prapas Muangjunburee ◽  
Jessada Wannasin
Keyword(s):  
Mechanical Properties ◽  
Solid State ◽  
Weld Metal ◽  
Butt Joint ◽  
A356 Aluminum Alloy ◽  
Globular Microstructure ◽  
Microstructure And Mechanical Properties ◽  
A356 Aluminum ◽  
Semi Solid ◽  
Solid State Joining

In this research, the semi-solid state joining of SSM A356 aluminum alloy was investigated. The butt-joint of SSM A356 was heated by an induction heating coil to create a localized semisolid pool. Then a stirrer was applied into the joint seam in order to mix the weld metal. The accurate controlling of temperature during joining was measured. The effects of stirring rate on physical, macrostructure, microstructure and mechanical properties were studied. Experimental results showed that increase in stirring rates, the surface of the joint was smooth. The weld metal consisted of the globular microstructure and also voids. The density of weld metal zone increased by an appropriate stirring. The best tensile strength was achieved with 1750 rpm, 70 mm/min for 103.4 MPa.

Study on Microstructures and Mechanical Properties of Rheo-Die Casting Semi-Solid A356 Aluminum Alloy

2006 ◽  
Vol 116-117 ◽  
pp. 453-456 ◽  
Author(s):  
Yong Lin Kang ◽  
Yue Xu ◽  
Zhao Hui Wang
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Die Casting ◽  
A356 Alloy ◽  
Experimental Results ◽  
A356 Aluminum Alloy ◽  
Microstructures And Mechanical Properties ◽  
A356 Aluminum ◽  
Semi Solid

In this paper, with a newly self-developed rotating barrel rheomoulding machine(RBRM), microstructures and mechanical properties of rheo-die casting A356 alloy were studied. In order to clearly show the characteristic of rheo-die casting, liquid die casting and semi-solid casting were done too. The experimental results showed that microstructures of rheo-die casting were composed of solid grains, which were finer and rounder, and had fewer pores. In the three technologies, integrated mechanical properties of semi-solid rheo-die casting were the best.

Effects of Electromagnetic Stirring Frequency on the Microstructure and Mechanical Properties of Al-7Si-0.42 Mg-0.1Cu Alloy by Semi-Solid Processing

2017 ◽  
Vol 898 ◽  
pp. 104-110 ◽  
Author(s):  
Peng Qi ◽  
Bo Long Li ◽  
Wen Jian Lv ◽  
Tong Bo Wang ◽  
Zuo Ren Nie
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Temperature ◽  
Fracture Morphology ◽  
Electromagnetic Stirring ◽  
Spherical Morphology ◽  
Microstructure And Mechanical Properties ◽  
Microstructures And Mechanical Properties ◽  
Semi Solid ◽  
Dendritic Structures

The effect of the different electromagnetic stirring frequency after low temperature pouring on microstructures and mechanical properties of Al-7Si-0.42 Mg-0.1Cu alloys was studied. It was found that the primary α-Al becomes smaller and tended to be spherical morphology, and the particles were uniformly distributed after electromagnetic stirring. The tensile strength of alloys improved gradually from 193.02 MPa to 212.54 MPa, and the elongation increased from 3.73% to 6.67% when the stirring frequency was 10 Hz. From the fracture morphology, the fracture for alloy stirred at frequency of 10 Hz showed more dimples than that without stirring. When the stirring frequency increased to 15 Hz, the microstructures of primary α-Al appeared to be dendritic structures, and the grains became coarse. As a result, the 10 Hz was the best electromagnetic stirring frequency.

Influence of Rare Earth Additions on the Microstructure and Mechanical Properties of Al7Si0.3Mg Alloys Processed by Semi-Solid Die Casting and Gravity Die Casting

2019 ◽  
Vol 285 ◽  
pp. 69-74 ◽  
Author(s):  
Long Fei Li ◽  
Da Quan Li ◽  
Min Luo ◽  
Yong Zhong Zhang ◽  
Yong Lin Kang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Rare Earth ◽  
Grain Boundaries ◽  
Die Casting ◽  
Eutectic Phase ◽  
Microstructure And Mechanical Properties ◽  
Die Cast ◽  
Rare Earth Additions ◽  
Semi Solid

Microstructures with fine globular grains and refined eutectic structures are important to enhance the mechanical properties of A356 alloys processed by semi-solid and gravity die casting. Rare earth (RE) additions have been shown to be capable of refining both the α-Al particles as well as modify the eutectic phase of alloys. In semi-solid die casting, Al7Si0.3Mg alloys with RE concentrations (0, 0.1 and 0.4 wt.%) were used to prepare semi-solid slurries using the SEED (Swirling Enthalpy Equilibrium Device) method, and subsequently semi-solid die cast. The same compositions of alloys were also applied to gravity die casting. The microstructure and mechanical properties of castings in two processes have been characterized. Compared to the grains produced in gravity die casting, globular grains with small size (260 μm) in the semi-solid die casting significantly enhance the UTS and elongation of alloys. Although the size of grains had no change with increasing RE concentrations in alloys. The Al-Si eutectics were changed to refined morphology with the 0.1 wt.% RE addition, which enhanced the ductility of alloys in two processes. When increasing the RE addition to 0.4 wt.%, the RE-rich phases precipitated at grain boundaries, which decreased the UTS and elongation of alloys.

Sign in / Sign up

Export Citation Format

Share Document