Oxidation-Resistance of (Ti,Al,Cr,Y)N Coatings Prepared by Arc Ion Plating

2010 ◽  
Vol 177 ◽  
pp. 338-341
Author(s):  
Ming Sheng Li ◽  
Yong Zhong Fan ◽  
Shu Juan Zhang
Keyword(s):  
Oxidation Resistance ◽  
Crystal Size ◽  
Substrate Bias ◽  
Compressor Blades ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Cr Content ◽  
Heat Treated ◽  
Aero Engine ◽  
Engine Compressor

In this study, composite metastable (Ti0.49Al0.49Y0.02)N, (Ti0.44Al0.44Cr0.1Y0.02)N and (Ti0.34Al0.34Cr0.3Y0.02)N coatings were respectively deposited on a wrought martensite steel 1Cr11Ni2W2MoV for aero-engine compressor blades by arc ion plating technique with a pulse substrate bias. All the coatings have B1NaCl phase structure with a (220) preferred orientation and dense structures. The introduction of chromium into the coatings gave rise to a minute shrinkage of crystal lattice and a decrease of crystal size. Annealed at 800°C, Oxidation-resistance of the coatings improved with increased Cr content. But heat-treated at 900°C, the incorporation of Cr gave rise to obvious decrease of oxidation-resistance.

Long-Term Oxidation Resistance of (Ti,Al,Y)N Coatings at 800 °C

2007 ◽  
Vol 546-549 ◽  
pp. 1789-1794 ◽  
Author(s):  
Ming Sheng Li ◽  
Chang Jie Feng ◽  
Fu Hui Wang ◽  
Wei Tao Wu
Keyword(s):  
Oxidation Resistance ◽  
Lattice Parameter ◽  
Metallic Elements ◽  
Compressor Blades ◽  
Outward Diffusion ◽  
Nitride Coatings ◽  
Aero Engine ◽  
Engine Compressor ◽  
Oxide Crystals

Composite metastable Ti0.5Al0.5N, Ti0.49Al0.49Y0.02N and Ti0.48Al0.48Y0.04N coatings were deposited on a wrought martensite steel 1Cr11Ni2W2MoV for aero-engine compressor blades by arc ion plating respectively all coatings possessed a dense surface and the same B1NaCl phase structure and the lattice parameter increased with increase of the incorporated element Y. Oxidation-resistance of (Ti,Al,Y)N coatings at 800 for up to 500 hr was investigated and the results showed that the introduction of yttrium into the coatings dramastically improved the oxidation-resistance of the coatings in air. The presence of Y in the nitride coatings suppresses the outer diffusion of Fe through the nitride coating. And the oxide of yttrium may segregate to the grain boundaries of oxides, suppressing the outward diffusion of metallic elements in coating and the inward diffusion of oxygen. Besides, the existence of adequate Y in the coatings is in favor of suppression of the growth of oxide crystals, formation layered oxide scale and decrease of compressive stress of oxidation.

Effect of bias voltage on the oxidation resistance of NiCoCrAlYTa coatings prepared by arc ion plating

2019 ◽  
Vol 147 ◽  
pp. 330-341 ◽  
Author(s):  
Shiming Xie ◽  
Mingjiang Dai ◽  
Songsheng Lin ◽  
Qian Shi ◽  
Chen Song ◽  
...  
Keyword(s):  
Oxidation Resistance ◽  
Bias Voltage ◽  
Arc Ion Plating ◽  
Ion Plating

Oxidition Resistance of Multi-Arc Ion Plating TiN Films

2013 ◽  
Vol 706-708 ◽  
pp. 180-183
Author(s):  
Jie Wang ◽  
Shi Hang Jiang ◽  
Juan Juan Wang
Keyword(s):  
Oxidation Resistance ◽  
Arc Ion Plating ◽  
Tin Films ◽  
Good Oxidation Resistance ◽  
Ion Plating ◽  
Oxidation Test ◽  
Tin Film ◽  
Cyclic Oxidation Test ◽  
Electron Spectrometry ◽  
Short Time

Depositing TiN Film on the surface of 4Cr5MoSiV1 with multi-arc ion plating technology method. And 350°C, 450°C, 550°C and 650 °C short oxidation test and 550 °C cyclic oxidation test. By scanning electron microscopy (SEM) and electron spectrometry (EDS) to analysis micro-structure and phase structure of test samples, study TiN film on oxidation resistance, and utilize indentation method to measure mechanical properties. Results show: In a short time under oxidizing conditions, at 550 °C the TiN film still has a good oxidation resistance. The film still have a sufficient bonding strength below 600 °C.

Microstructure, Hardness and Oxidation Resistance of CrN and CrAlN Coatings Synthesized by Multi-Arc Ion Plating Technology

2010 ◽  
Vol 168-170 ◽  
pp. 2430-2433 ◽  
Author(s):  
Zhi Hai Cai ◽  
Zhang Ping ◽  
Yue Lan Di
Keyword(s):  
Oxidation Resistance ◽  
Steel Substrate ◽  
Composite Coatings ◽  
Spring Steel ◽  
X Ray Diffraction ◽  
Arc Ion Plating ◽  
X Ray ◽  
Ion Plating ◽  
Al Content ◽  
Crn Coatings

Approximately 2 μm thick CrN and CrAlN coatings were synthesized on silicon and spring steel substrate by multi-arc ion plating technology. The nanoindentation techniques, Auger electron spectroscopy (AES) analysis, scanning electron microscopy, X-ray diffraction and oxidation furnace were used to investigate the mechanical property, oxidation resistance and microstructure of the coatings. The XRD data showed that the CrN and CrAlN coatings exhibited B1 NaCl structure. Nanoindentation measurements showed that as-deposited CrN and CrAlN coatings exhibited a hardness of 19 and 30 GPa respectively. Compared with CrN coatings, the CrAlN composite coatings show much better oxidation resistance. And the oxidation resistance ability will enhance with increasing Al content, because A12O3 will form after oxidation in high temperature condition which could reduce the diffusivity ability of oxygen.

Sign in / Sign up

Export Citation Format

Share Document