Structural Evolution in the Processing of Fe/ BaFe12O19 Nano Composite via Mechanical Alloying

2008 ◽  
Vol 55-57 ◽  
pp. 569-572
Author(s):  
Abolghasem Ataie ◽  
R. Nikkhah-Moshaie
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Milling Time ◽  
Magnetic Phase ◽  
Sol Gel ◽  
Barium Hexaferrite ◽  
Combustion Method ◽  
Magnetic Composite ◽  
Phase Constitution ◽  
Mean Particle Size

Barium hexaferrite particles derived from sol-gel combustion method with a mean particle size of 160 nm and Fe particles with a mean particle size of 150 µm were mechanically alloyed using planetary ball mill. Phase constitution and EDS analysis of the products were investigated by XRD and SEM, respectively. Magnetic properties of samples were measured by VSM. Influence of the milling time and Fe content on the phase constitution of synthesized composites has been investigated. XRD results indicated that in sample with 90 and 50wt% Fe, the magnetic composite with enhanced magnetic properties, formed based on Fe phase while barium hexaferrite particles embedded within Fe particles. In sample with 90% Fe, the crystallite size of Fe reduced from 173 to 87 nm by increasing the milling time from 1 to 20 h; saturation magnetization of the 20 h milled sample was measured as 94.8 emu/g. Besides, in sample with 50wt% Fe, some FeO phase was detected which is probably due to the partial decomposition of hard magnetic phase during milling. Sample with 10wt% Fe showed completely different behavior and magnetite appeared as a major magnetic phase.

Static and Dynamic Magnetic Properties of Nanosized Barium Hexaferrite Powders Prepared by the Sol–Gel Combustion Method

2015 ◽  
Vol 58 (1) ◽  
pp. 125-132 ◽  
Author(s):  
E. P. Naiden ◽  
V. A. Zhuravlev ◽  
R. V. Minin ◽  
V. I. Itin ◽  
E. Yu. Korovin
Keyword(s):  
Magnetic Properties ◽  
Sol Gel ◽  
Barium Hexaferrite ◽  
Combustion Method ◽  
Gel Combustion ◽  
Gel Combustion Method

Dielectric and magnetic properties of Zn-substituted Co2Y barium hexaferrite prepared by sol–gel auto combustion method

2016 ◽  
Vol 494 ◽  
pp. 33-40 ◽  
Author(s):  
I. Odeh ◽  
H.M. El Ghanem ◽  
S.H. Mahmood ◽  
S. Azzam ◽  
I. Bsoul ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Sol Gel ◽  
Barium Hexaferrite ◽  
Combustion Method ◽  
Auto Combustion

scholarly journals Loading Effect of Sol-Gel Derived Barium Hexaferrite on Magnetic Polymer Composites

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 558
Author(s):  
Thanida Charoensuk ◽  
Wannisa Thongsamrit ◽  
Chesta Ruttanapun ◽  
Pongsakorn Jantaratana ◽  
Chitnarong Sirisathitkul
Keyword(s):  
Polymer Composites ◽  
Sol Gel ◽  
Weight Ratio ◽  
Barium Hexaferrite ◽  
Acrylonitrile Butadiene Styrene ◽  
Combustion Method ◽  
Casting Method ◽  
Auto Combustion ◽  
Solution Casting Method ◽  
Butadiene Styrene

Solution–processing methods were investigated as viable alternatives to produce the polymer-bonded barium hexaferrite (BaM). BaM powders were first synthesized by using the sol-gel auto-combustion method. While the ignition period in two synthesis batches varied, the morphology of hexagonal microplates and nanorods, as well as magnetic properties, were reproduced. To prepare magnetic polymer composites, these BaM powders were then incorporated into the acrylonitrile-butadiene-styrene (ABS) matrix with a weight ratio of 80:20, 70:30, and 60:40 by using the solution casting method. Magnetizations were linearly decreased with a reduction in ferrite loading. Compared to the BaM loose powders and pressed pellet, both remanent and saturation magnetizations were lower and gave rise to comparable values of the squareness. The squareness around 0.5 of BaM samples and their composites revealed the isotropic alignment. Interestingly, the coercivity was significantly increased from 1727–1776 Oe in loose BaM powders to 1874–2052 Oe for the BaM-ABS composites. These composites have potential to be implemented in the additive manufacturing of rare-earth-free magnets.

scholarly journals Green synthesis and characterization of hexaferrite strontium-perovskite strontium photocatalyst nanocomposites

2020 ◽  
Vol 43 (1) ◽  
pp. 26-42 ◽  
Author(s):  
Zahra Hajian Karahroudi ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Magnetic Properties ◽  
Green Synthesis ◽  
Sol Gel ◽  
Synthesis Method ◽  
Combustion Method ◽  
Lemon Juice ◽  
X Ray Diffraction ◽  
X Ray ◽  
Auto Combustion

AbstractThis study presents a preparation of SrFe12O19– SrTiO3 nanocomposite synthesis via the green auto-combustion method. At first, SrFe12O19 nanoparticles were synthesized as a core and then, SrTiO3 nanoparticles were prepared as a shell for it to manufacture SrFe12O19–SrTiO3 nanocomposite. A novel sol-gel auto-combustion green synthesis method has been used with lemon juice as a capping agent. The prepared SrFe12O19–SrTiO3 nanocomposites were characterized by using several techniques to characterize their structural, morphological and magnetic properties. The crystal structures of the nanocomposite were investigated via X-ray diffraction (XRD). The morphology of SrFe12O19– SrTiO3 nanocomposite was studied by using a scanning electron microscope (SEM). The elemental composition of the materials was analyzed by an energy-dispersive X-ray (EDX). Magnetic properties and hysteresis loop of nanopowder were characterized via vibrating sample magnetometer (VSM) in the room temperature. Fourier transform infrared spectroscopy (FTIR) spectra of the samples showed the molecular bands of nanoparticles. Also, the photocatalytic behavior of nanocomposites has been checked by the degradation of azo dyes under irradiation of ultraviolet light.

Annealing Effects on the Physical and Magnetic Properties of Tb1.5Y1.5Fe5O12 Films Nanoparticles Prepared by Sol-Gel Method

2013 ◽  
Vol 756 ◽  
pp. 91-98 ◽  
Author(s):  
Ftema W. Aldbea ◽  
Noor Bahyah Ibrahim ◽  
Mustafa Hj. Abdullah
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Annealing Temperature ◽  
Quartz Substrate ◽  
Sol Gel ◽  
Lattice Parameter ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Iron Garnet

Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900 °C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900°C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-raySpectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealingtemperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. Normal 0 21 false false false MS X-NONE X-NONE MicrosoftInternetExplorer4 Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900°C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900 °C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-ray Spectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealing temperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

Preparation of Magnesium-Based Cobalt-Ferrites (Co1−xMgxFe2O4) Nanoparticles by Sol–Gel Auto Combustion Method

2017 ◽  
Vol 17 (01n02) ◽  
pp. 1760012
Author(s):  
S. Gowreesan ◽  
A. Ruban Kumar
Keyword(s):  
Particle Size ◽  
Structural Parameters ◽  
Sol Gel ◽  
Average Particle Size ◽  
Combustion Method ◽  
Dielectric Behavior ◽  
Powder Xrd ◽  
Average Particle ◽  
Cobalt Ferrites ◽  
Auto Combustion

The scope of the present work is in enhancing the particle size, and dielectric properties of Mg-substituted Cobalt ferrites nanoparticles prepared by sol–gel auto combustion method. The different ratios of Mg-substituted Co Ferrites (Co[Formula: see text]MgxFe2O4([Formula: see text], 0.05, 0.10, 0.15, 0.20 and 0.30)) are calcinated at 850[Formula: see text]C. The synthesized nanoparticles were characterized by powder XRD, FTIR, FE-SEM, EDX techniques and dielectric behavior. The structural parameters were confirmed from powder XRD and the average particle size is obtained from 39 to 67 nm due to the substitution of Mg[Formula: see text] which was calculated by Debye Scherrer’s formula. FE-SEM showed the surface morphology of the different ratio of the sample. The dielectric loss has measured the frequency range of 50[Formula: see text]Hz–5[Formula: see text]MHz. From electrical modulus, conductivity relaxation and thermal activation of charge carriers has been discussed.

Sign in / Sign up

Export Citation Format

Share Document