Research & Design of the Multifunctional Landscape Hedge Trimmer

2013 ◽  
Vol 690-693 ◽  
pp. 3377-3380
Author(s):  
Yan Mei Meng ◽  
Jin Wei ◽  
Jian Zhi Liang ◽  
Zhen Dong ◽  
Chun Wa Qin ◽  
...  
Keyword(s):  
Error Compensation ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Control Software ◽  
The Core ◽  
Single Person ◽  
Multifunctional Landscape ◽  
Online Interpolation ◽  
6 Degrees Of Freedom ◽  
Compensation Function

This paper presents a multifunctional landscape hedge trimmer. It has 6 degrees of freedom, and it can trim the shape of flat, cylinder, cone, sphere, etc. The controller takes the embedded LINUX ARM9 processor as the core. It has a high-speed real-time online interpolation function, and an error compensation function. With the help of the developed control software it can control the trimming process automatically, making the trimming speed faster and the precision higher, and with its single-person operation feature, it greatly reduces the labor intensity and improves the labor efficiency.

scholarly journals Trajectory optimization of the 6-degrees-of-freedom high-speed parallel robot based on B-spline curve

2019 ◽  
Vol 103 (1) ◽  
pp. 003685041988011
Author(s):  
Jiangping Mei ◽  
Fan Zhang ◽  
Jiawei Zang ◽  
Yanqin Zhao ◽  
Han Yan
Keyword(s):  
Trajectory Optimization ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Control Point ◽  
Parallel Robot ◽  
B Spline ◽  
Spline Curve ◽  
Deformation Problem ◽  
Point Subset ◽  
6 Degrees Of Freedom

According to the problem that the existing high-speed parallel robot cannot satisfy the operation requirements of non-planar industrial production line, a 6-degrees-of-freedom high-speed parallel robot is proposed to carry out the kinematic and dynamic analyses. Combining with the door-type trajectory commonly used by the parallel robot, it adopts 3-, 5-, and 7-time B-spline curve motion law to conduct the trajectory planning in operation space. Taking the average cumulative effect of joint jerky as the optimization target, a trajectory optimization method is proposed to improve the smoothness of robot end-effector motion with the selected motion law. Furthermore, to solve the deformation problem of the horizontal motion stage of the trajectory, a mapping model between the control point subset of B-spline and the motion point subset of trajectory is established. Based on the main diagonally dominant characteristic of the coefficient matrix, the trajectory deformation evaluation index is constructed to optimize the smoothness and minimum deformation of the robot motion trajectory. Finally, compared to without the optimization, the maximum robot joint jerk decreases by 69.4% and 72.3%, respectively, and the maximum torque decreases by 51.4% and 38.9%, respectively, under a suitable trajectory deformation.

scholarly journals Aerodynamics of inclined cylindrical bodies free-flying in a hypersonic flowfield

2021 ◽  
Vol 62 (9) ◽  
Author(s):  
Patrick M. Seltner ◽  
Sebastian Willems ◽  
Ali Gülhan ◽  
Eric C. Stern ◽  
Joseph M. Brock ◽  
...  
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Numerical Data ◽  
Static Stability ◽  
Free Flight ◽  
Aerodynamic Coefficients ◽  
Flow Topology ◽  
Motion Data ◽  
Continuous Rotation ◽  
German Aerospace

Abstract The influence of the flight attitude on aerodynamic coefficients and static stability of cylindrical bodies in hypersonic flows is of interest in understanding the re/entry of space debris, meteoroid fragments, launch-vehicle stages and other rotating objects. Experiments were therefore carried out in the hypersonic wind tunnel H2K at the German Aerospace Center (DLR) in Cologne. A free-flight technique was employed in H2K, which enables a continuous rotation of the cylinder without any sting interferences in a broad angular range from 0$$^{\circ }$$ ∘ to 90$$^{\circ }$$ ∘ . A high-speed stereo-tracking technique measured the model motion during free-flight and high-speed schlieren provided documentation of the flow topology. Aerodynamic coefficients were determined in careful post-processing, based on the measured 6-degrees-of-freedom (6DoF) motion data. Numerical simulations by NASA’s flow solvers Cart3D and US3D were performed for comparison purposes. As a result, the experimental and numerical data show a good agreement. The inclination of the cylinder strongly effects both the flowfield and aerodynamic loads. Experiments and simulations with concave cylinders showed marked difference in aerodynamic behavior due to the presence of a shock–shock interaction (SSI) near the middle of the model. Graphic abstract

4D in in vivo 2-photon laser scanning fluorescence microscopy with sample motion in 6 degrees of freedom

2011 ◽  
Vol 200 (1) ◽  
pp. 47-53 ◽  
Author(s):  
Sabine Scheibe ◽  
Mario M. Dorostkar ◽  
Christian Seebacher ◽  
Rainer Uhl ◽  
Frank Lison ◽  
...  
Keyword(s):  
Fluorescence Microscopy ◽  
Laser Scanning ◽  
Degrees Of Freedom ◽  
Sample Motion ◽  
6 Degrees Of Freedom

Workspace, dexterity and dimensional optimization of microhexapod

2015 ◽  
Vol 35 (4) ◽  
pp. 341-347 ◽  
Author(s):  
E. Rouhani ◽  
M. J. Nategh
Keyword(s):  
Degrees Of Freedom ◽  
Optimization Problem ◽  
Screw Theory ◽  
Design Parameters ◽  
Dimensional Synthesis ◽  
Content Type ◽  
Workspace Analysis ◽  
The Difference ◽  
Flexure Joints ◽  
6 Degrees Of Freedom

Purpose – The purpose of this paper is to study the workspace and dexterity of a microhexapod which is a 6-degrees of freedom (DOF) parallel compliant manipulator, and also to investigate its dimensional synthesis to maximize the workspace and the global dexterity index at the same time. Microassembly is so essential in the current industry for manufacturing complicated structures. Most of the micromanipulators suffer from their restricted workspace because of using flexure joints compared to the conventional ones. In addition, the controllability of micromanipulators inside the whole workspace is very vital. Thus, it is very important to select the design parameters in a way that not only maximize the workspace but also its global dexterity index. Design/methodology/approach – Microassembly is so essential in the current industry for manufacturing complicated structures. Most of the micromanipulators suffer from their restricted workspace because of using flexure joints compared to the conventional ones. In addition, the controllability of micromanipulators inside the whole workspace is very vital. Thus, it is very important to select the design parameters in a way that not only maximize the workspace but also its global dexterity index. Findings – It has been shown that the proposed procedure for the workspace calculation can considerably speed the required calculations. The optimization results show that a converged-diverged configuration of pods and an increase in the difference between the moving and the stationary platforms’ radii cause the global dexterity index to increase and the workspace to decrease. Originality/value – The proposed algorithm for the workspace analysis is very important, especially when it is an objective function of an optimization problem based on the search method. In addition, using screw theory can simply construct the homogeneous Jacobian matrix. The proposed methodology can be used for any other micromanipulator.

A Magnetic Drive Actuator for Micro Electrical Discharge Machining

2012 ◽  
Vol 591-593 ◽  
pp. 303-306
Author(s):  
Xiao You Zhang ◽  
Akio Kifuji ◽  
Dong Jue He
Keyword(s):  
Electrical Discharge ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Electrical Discharge Machining ◽  
Magnetic Coupling ◽  
Magnetic Bearings ◽  
Coupling Mechanism ◽  
Micro Electrical Discharge Machining ◽  
Long Stroke ◽  
Magnetic Drive

Electrical discharge machining has the capability of machining all conductive materials regardless of hardness, and has the ability to deal with complex shapes. However, the speed and accuracy of conventional EDM are limited by probability and efficiency of the electrical discharges. This paper describes a three degrees of freedom (3-DOF) controlled, wide-bandwidth, high-precision, long-stroke magnetic drive actuator. The actuator can be attached to conventional electrical discharge machines to realize a high-speed and high-accuracy EDM. The actuator primarily consists of thrust and radial magnetic bearings, thrust and radial air bearings and a magnetic coupling mechanism. By using the thrust and radial magnetic bearings, the translational motions of the spindle can be controlled. The magnetic drive actuator possesses a positioning resolution of the order of micrometer, a bandwidth greater than 100Hz and a positioning stroke of 2mm.

An improved calibration curve between soil pH measured in waterand CaCl2

Soil Research ◽  
2002 ◽  
Vol 40 (8) ◽  
pp. 1399 ◽  
Author(s):  
B. L. Henderson ◽  
E. N. Bui
Keyword(s):  
Statistical Analysis ◽  
Water Resources ◽  
Soil Ph ◽  
Calibration Curve ◽  
Smooth Function ◽  
Degrees Of Freedom ◽  
Additive Model ◽  
Smoothing Spline ◽  
Look Up Table ◽  
6 Degrees Of Freedom

A new pH water to pH CaCl2 calibration curve was derived from data pooled from 2 National Land and Water Resources Audit projects. A total of 70465 observations with both pH in water and pH in CaCl2 were available for statistical analysis. An additive model for pH in CaCl2 was fitted from a smooth function of pH in water created by a smoothing spline with 6 degrees of freedom. This model appeared stable outside the range of the data and performed well (R2 = 96.2, s = 0.24). The additive model for conversion of pHw to pHCa is sigmoidal over the range of pH 2.5 to 10.5 and is similar in shape to earlier models. Using this new model, a look-up table for converting pHw to pHCa was created.

Design, Construction and Control of a Remotely Operated Vehicle (ROV)

2011 ◽  
Author(s):  
Alireza Marzbanrad ◽  
Jalil Sharafi ◽  
Mohammad Eghtesad ◽  
Reza Kamali
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Remotely Operated Vehicle ◽  
Six Degrees Of Freedom ◽  
Depth Sensors ◽  
Control Schemes ◽  
On Line ◽  
Operation Unit ◽  
And Control ◽  
Design Construction

This is report of design, construction and control of “Ariana-I”, an Underwater Remotely Operated Vehicle (ROV), built in Shiraz University Robotic Lab. This ROV is equipped with roll, pitch, heading, and depth sensors which provide sufficient feedback signals to give the system six degrees-of-freedom actuation. Although its center of gravity and center of buoyancy are positioned in such a way that Ariana-I ROV is self-stabilized, but the combinations of sensors and speed controlled drivers provide more stability of the system without the operator involvement. Video vision is provided for the system with Ethernet link to the operation unit. Control commands and sensor feedbacks are transferred on RS485 bus; video signal, water leakage alarm, and battery charging wires are provided on the same multi-core cable. While simple PI controllers would improve the pitch and roll stability of the system, various control schemes can be applied for heading to track different paths. The net weight of ROV out of water is about 130kg with frame dimensions of 130×100×65cm. Ariana-I ROV is designed such that it is possible to be equipped with different tools such as mechanical arms, thanks to microprocessor based control system provided with two directional high speed communication cables for on line vision and operation unit.

Sign in / Sign up

Export Citation Format

Share Document