Effect of Compatibilizers on Mechanical and Thermal Properties of High Density Polyethylene Filled with Bio-Filler from Eggshell

2013 ◽  
Vol 699 ◽  
pp. 57-62
Author(s):  
Wanikorn Buakaew ◽  
Ruksakulpiwat Yupaporn ◽  
Nitinat Suppakarn ◽  
Wimonlak Sutapun
Keyword(s):  
Thermal Properties ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
High Density Polyethylene ◽  
Average Particle Size ◽  
High Density ◽  
Degree Of Crystallinity ◽  
Average Particle ◽  
Mechanical And Thermal Properties ◽  
The Impact

In this research work, the effect of compatibilizers on mechanical and thermal properties of ESP/HDPE composites was investigated. High density polyethylene grafted with maleic anhydride (HDPE-g-MA) and ethylene propylene rubber grafted with maleic anhydride (EPR-g-MA) were used to compatibilize the ESP/HDPE composites. The ESP/HDPE composite with and without the compatibilizes was prepared at 20 wt.% ESP. The volume average particle size of ESP was 20.35 µm. The compatibilized HDPE composites were prepared at 2, 5, 8 and 10 wt.% of HDPE-g-MA and at 2, 5, 8 and 10 wt.% of EPR-g-MA, as well. It was found that ultimate stress, yield strength, and elongation at break of the ESP/HDPE composites prepared with HDPE-g-MA increased with increasing HDPE-g-MA content. In addition, Young’s modulus was maximum at 8 wt.% HDPE-g-MA. The composites filled with HDPE-g-MA had improved impact strength with increasing HDPE-g-MA content. On the other hand, the composites with EPR-g-MA showed a decrease in tensile properties and impact strength when increasing EPR-g-MA content. The impact strength of the HDPE composites compatibilized with EPR-g-MA decreased with increasing EPR-g-MA content. In addition, degree of crystallinity of the composites with EPR-g-MA was higher than that of the composite with HDPE-g-MA. Furthermore, compatibilizing ESP/HDPE composites with either HDPE-g-MA or EPR-g-MA did not influence HDPE and ESP decomposition temperatures, HDPE melting temperature and HDPE crystallization temperature.

Effect of maleic anhydride on the mechanical and thermal properties of hemp/high-density polyethylene green composites

2015 ◽  
Vol 121 (1) ◽  
pp. 93-105 ◽  
Author(s):  
Eleftheria Roumeli ◽  
Zoe Terzopoulou ◽  
Eleni Pavlidou ◽  
Konstantinos Chrissafis ◽  
Electra Papadopoulou ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Maleic Anhydride ◽  
High Density Polyethylene ◽  
High Density ◽  
Mechanical And Thermal Properties ◽  
Green Composites

Evaluation of the Aging Behavior of High Density Polyethylene in Thermal Oxidative Environment by Principal Component Analysis

2017 ◽  
Vol 727 ◽  
pp. 447-449 ◽  
Author(s):  
Jun Dai ◽  
Hua Yan ◽  
Jian Jian Yang ◽  
Jun Jun Guo
Keyword(s):  
Principal Component Analysis ◽  
Impact Strength ◽  
High Density Polyethylene ◽  
Tensile Modulus ◽  
Principal Component ◽  
Component Analysis ◽  
High Density ◽  
Aging Behavior ◽  
Data Set ◽  
The Impact

To evaluate the aging behavior of high density polyethylene (HDPE) under an artificial accelerated environment, principal component analysis (PCA) was used to establish a non-dimensional expression Z from a data set of multiple degradation parameters of HDPE. In this study, HDPE samples were exposed to the accelerated thermal oxidative environment for different time intervals up to 64 days. The results showed that the combined evaluating parameter Z was characterized by three-stage changes. The combined evaluating parameter Z increased quickly in the first 16 days of exposure and then leveled off. After 40 days, it began to increase again. Among the 10 degradation parameters, branching degree, carbonyl index and hydroxyl index are strongly associated. The tensile modulus is highly correlated with the impact strength. The tensile strength, tensile modulus and impact strength are negatively correlated with the crystallinity.

scholarly journals Effect of adding TiO2 nanoparticles on the SEM morphology and mechanical properties of conventional heat-cured acrylic resin

2019 ◽  
Vol 13 (3) ◽  
pp. 234-240
Author(s):  
Elnaz Moslehifard ◽  
Mahmood Robati Anaraki ◽  
Saeed Shirkavand
Keyword(s):  
Impact Strength ◽  
Tio2 Nanoparticles ◽  
Cross Sections ◽  
Average Particle Size ◽  
Acrylic Resin ◽  
Mechanical Tests ◽  
Average Particle ◽  
Sem Images ◽  
Tio2 Nps ◽  
The Impact

Background. The current study evaluated the compressive, flexural and impact strengths of heat-cured acrylic resins reinforced by TiO2 nanoparticles (NPs). Methods. TiO2 NPs were provided and characterized using scanning electron microscopy (SEM) to determine their morphology and crystalline structure. For three mechanical tests, 12 acrylic resin groups (n=9), totaling 108 specimens, were prepared using a special mold for each test, with TiO2 nanoparticle contents of 0, 0.5, 1 or 2 wt% in different groups. After curing, the compressive, flexural and impact strengths of the specimens were examined according to ISO 1567. Results. In the SEM and XRD study of TiO2 NPs, anatase was identified as the major crystalline phase followed by rutile (average particle size: 20.4 nm). SEM images showed that the nanocomposite with 1 wt% NPs had a more homogenized blend. 1 wt% TiO2 nanocomposite exhibited a higher, but non-significant, impact strength compared to the controls. ANOVA showed significant differences in the impact and flexural strengths between nanocomposites with various contents of TiO2 NPs. Conclusion. The nanocomposite with 1 wt% TiO2 NPs exhibited fewer micro-pores and micro-cracks in the SEM cross-sections. A non-significant increase was also observed in the impact strength with TiO2 NPs at 1 wt%. Further increase in TiO2 NPs decreased both the impact and flexural strengths. The compressive strength of the heat-cured acrylic resin was not affected by the incorporation of NPs.

Sign in / Sign up

Export Citation Format

Share Document