degree of crystallinity
Recently Published Documents


TOTAL DOCUMENTS

1150
(FIVE YEARS 426)

H-INDEX

41
(FIVE YEARS 7)

2022 ◽  
Author(s):  
Hamid Hosseinzadeh ◽  
Hamidreza Oveisi

Abstract In the present study, CoFe2O4 and CoFe2-xGdxO4 nanoparticles were synthesized by the hydrothermal process. The CoFe2O4 nanoparticles were synthesized at different temperatures (70oC, 100oC, 150oC, and 200oC), molar ratio of CoCl2/ FeCl3 (0/2, 0.75/2, 1/2, 1.5/2, and 2/2). Gadolinium-doped cobalt ferrite (CoFe2-xGdxO4) nanoparticles have also been synthesized with Gd/Fe molar ratios of 0.18 and 0.53. The XRD patterns indicate that cobalt ferrite and Gadolinium-doped cobalt ferrite nanoparticles have been successfully synthesized without impurities with a medium degree of crystallinity. The XRD patterns show that by increasing the synthesis temperature from 70oC to 200oC, the size of the nanoparticles decreased from 50.49nm to 32.45nm while the morphology of the nanoparticles also changed from a shapeless and agglomerated state to a spherical shape. The XPS curve illustrated several peaks corresponding to Fe+3, Co+2, and O 1s. The binding energies for Co and Fe were consistent with Fe 2p and Co 2p binding energies for cobalt ferrite nanoparticles. The magnetic saturation value (Ms) increased from 17.253 emu/g to 54.438 emu/g with a rise in the synthesis temperature. The effects of FeCl3/CoCl2 molar ratio on the magnetic properties showed the highest value of Ms (54.438 emu/g) and the coercivity (HC) of 744.56 Oe for a 2/1 molar ratio. The addition of gadolinium to the composition resulted in a reducing of the magnetic properties of nanoparticles; accordingly, the amount of saturated magnetization was reduced to 22.469 emu/g. Another effect of gadolinium dopant in the composition was a change in nanoparticle morphology from spherical to rod shape. The final aim of this study was to investigate the possible utilization of CoFe2O4 and CoFe2-xGdxO4 nanoparticles in medical treatment in the near future.


Crystals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 106
Author(s):  
Hoang Thi Phuong ◽  
Nguyen Kim Thoa ◽  
Phung Thi Anh Tuyet ◽  
Quyen Nguyen Van ◽  
Yen Dao Hai

Cellulose nanomaterials (CNs) are renewable, bio-derived materials that can address not only technological challenges but also social impacts. This ability results from their unique properties, for example, high mechanical strength, high degree of crystallinity, biodegradable, tunable shape, size, and functional surface chemistry. This minireview provides chemical and physical features of cellulose nanomaterials and recent developments as an adsorbent and an antimicrobial material generated from bio-renewable sources.


Author(s):  
A. ARUL JEYA KUMAR ◽  
NIRANJAN S. RAJ ◽  
C. SAIPRASAD ◽  
AGHALAYAM R. SUDHANVA

This paper is focused on the analysis of the morphological and thermal properties of the biomedical composites, polylactic acid (PLA) and polycaprolactone (PCL) matrix, reinforced with basalt fibers (BFs) and using halloysite nanotubes (HNT) as filler material. Four different composites, viz. PPHB 1, PPHB 2, PPHB 3 and PPHB 4, are obtained by varying the weight fractions of these materials using twin-screw extrusion followed by injection molding. The morphological characterization is performed on these composites using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. SEM reveals homogenous and strong bonding between the matrix, reinforcement and filler. The BF are well embedded in the matrix with a random orientation. No formation of voids and cracks is observed. The functional groups present and the types of vibration experienced by the chemical bonds were observed in the FTIR spectra. The composites are subjected to thermal testing such as differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The PPHB 2, which contains 80% PLA, 10% BF, 7% PCL and 3% HNT, has the highest degree of crystallinity, as revealed by DSC, and exhibits the most optimum thermal degradation characteristics as indicated by TGA.


2022 ◽  
pp. 152808372110608
Author(s):  
Adham Rafikov ◽  
Nodir Mirzayev ◽  
Sevara Alimkhanova

Five types of multilayer nonwovens for clothing and footwear parts were obtained by the adhesive bonding method. The thickest middle layer of the material consists of evenly laid coarse camel or sheep fibers or of reconstituted cotton fibers from flaps, the upper and lower layers consist of knitwear, and polymer adhesive is located between the layers. The layers are bonded by thermal pressing at a temperature of 150 ± 5°C for 2.0 ± 0.2 min. The microstructure and morphology of fibers, polymer adhesive, and multilayer nonwoven fabric were investigated by FT-IR spectroscopy, SEM, and X-ray phase analysis. The chemical interaction between wool fibers and polymer adhesive, the geometric dimensions and shape of the fibers, the structure and morphology of the cross section of the layers of the material, and the change in the degree of crystallinity of the material have been established. The investigated coarse and thick fibers of camel and sheep wool are more suitable for the production of nonwoven textile material. In the process of thermal exposure, the molten polymer diffuses into the structure of the nonwoven layer and knitted fabric. The diffusion and excellent adhesion of the molten polymer to the fibers ensures the solidity and strength of the composite. The developed design provides high strength of the material as a whole and adhesive strength between layers, high heat-retaining properties, and the use of a mesh adhesive film provides sufficient air and vapor permeability.


2022 ◽  
Author(s):  
Abdelaziz Abu El-fadl ◽  
Amna Eltokhey ◽  
A. A. Abu-Sehly ◽  
Amina A. Abozeed

Abstract In the present study, Fex/ZrO2 (0 ≤ x ≤ 25) nanoparticles were synthesized by a facile modified Sol-Gel method. Stabilization of the tetragonal phase of ZrO2 is studied as a function of both the Fe incorporation ratios and thermal treatment. The Fe incorporation ratios are tested up to the extreme just before FeO and Fe2O3 phases are formed separately. The prepared Fex/ZrO2 nanoparticles XRD analysis depicts the formation of zirconium oxide at different Fe ratios in the nanoscale with an excellent degree of crystallinity in the tetragonal phase. The effect of thermal treatment on stabilizing the tetragonal phase of Fex/ZrO2 nanoparticles is extensively studied. The phase transition to the monoclinic phase is determined as function of Fe incorporation ratios and annealing temperatures. The optical absorbance spectra showed that the optical band gap decreased with increasing Fe ratios without the formation of doping bands which confirms the formation of Fex/ZrO2 single matrix.


2022 ◽  
Author(s):  
M. Podzorova

Abstract. The mechanical properties of polymer composites based on polylactide vary significantly over a wide range of values. It has been established that photodegradation of low-density polyethylene – polylactide blends occurs both in the amorphous and in the crystalline phase of the PLA matrix, which leads to deterioration of the mechanical properties of the studied mixtures. Ozonolysis affects the strength parameters of polylactide-polyethylene samples as well as photodegradation. By the differential scanning calorimetry it is determined that the melting point of polylactide decreases by 2-4 °C, the glass transition temperature - by 1-3 °C, while the degree of crystallinity increases by 3-6%. In the process of ozonolysis, the thermophysical characteristics of PLA/LDPE have changed.


MOMENTO ◽  
2022 ◽  
pp. 66-82
Author(s):  
Edson A. S. Filho ◽  
Carlos B. B. Luna ◽  
Adriano L. Silva ◽  
Eduardo S. B. Ferreira ◽  
Edcleide M. Araújo ◽  
...  

The heat treatment effect on kaolin waste from mining was evaluated on the structural and thermal behavior of poly(ε-caprolactone) (PCL). The PCL/KW (kaolin waste) and PCL/HTKW (heat-treated kaolin waste) composites were processed in an internal mixer and subsequently characterized by X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The kaolin waste showed kaolinite and quartz in its composition, while the heat treatment at 1200°C modified it to mullite, quartz and silica-rich amorphous phase. By XRD, there was an increase in the intensity of the peak 2θ = 23.9° of the PCL/KW composites compared to neat PCL. In contrast, PCL/HTKW composites tended to reduce the intensity of the peak 2θ = 23.9°, especially at 5% HTKW. The crystalline melting temperature and the degree of crystallinity of PCL/KW and PCL/HTKW composites were practically unchanged, compared to PCL. However, the crystallization process was more effective with the kaolin waste (KW) without heat treatment, indicating that the HTKW amorphous phase inhibited crystallization. The PCL/KW development promoted an increase in crystallization temperature, relative crystallinity, and crystallization rate, surpassing PCL and the PCL/HTKW system. In view of this, kaolin waste has the potential to accelerate the PCL crystallization process, contributing to add value to a material that would otherwise be discarded and minimizing environmental impacts.


Author(s):  
Marina A. Gorbunova ◽  
Evgenii V. Komov ◽  
Leonid Yu. Grunin ◽  
Mariya S. Ivanova ◽  
Ainur F. Abukaev ◽  
...  

Control of the phase separation process of soft and hard segments by selecting diisocyanates and by varying the thermal program allows defining the final degree of crystallinity and phase composition of TPUs.


Author(s):  
Khatun A Jannath ◽  
Mahmood Hassan Akhtar ◽  
NG Gurudatt ◽  
Deog-Su Park ◽  
Kwang Bok Kim ◽  
...  

Octahedral SrMoO4 nanoparticles (NPs) with a high degree of crystallinity and controlled size (250-350 nm) were synthesized for the first time by employing a facile hydrothermal method. The prepared NPs...


2021 ◽  
Vol 116 ◽  
pp. 5-14
Author(s):  
Marta Babicka ◽  
Magdalena Woźniak ◽  
Kinga Szentner ◽  
Sławomir Borysiak ◽  
Krzysztof Dwiecki ◽  
...  

The aim of this study was to compare parameters of nanocellulose obtained by two different procedures: hydrolysis with ionic liquids (1-allyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium acetate) and hydrolysis with ionic liquids in combination with hydrolysis using a cellulolytic enzyme from Trichoderma reesei. Avicel cellulose was treated with two ionic liquids: 1-allyl-3-methylimidazolium chloride (AmimCl) and 1-ethyl 3-methylimidazolium acetate (EmimOAc). In the two-step hydrolysis cellulose after treatment with ionic liquids was additionally hydrolyzed with a solution of enzymes. In order to characterize the obtained material, the following analyses were used: infrared spectroscopy, X-ray diffraction and dynamic light scattering. The results indicated that cellulose obtained by two-step nanocellulose production methods (first hydrolysis with ionic liquids and then with enzymes) showed similar parameters (particle size, XRD patterns and degree of crystallinity) as the material after the one-step process, i.e. hydrolysis with ionic liquids.


Sign in / Sign up

Export Citation Format

Share Document