Effects of Combined Ultrasonic Vibration during the Sinking EDM Process for Cemented Carbide

2009 ◽  
Vol 76-78 ◽  
pp. 657-663 ◽  
Author(s):  
Chaiya Praneetpongrung ◽  
Yasushi Fukuzawa ◽  
Shigeru Nagasawa
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Cemented Carbide ◽  
Electrode Wear ◽  
Machining Properties ◽  
Edm Process

In recent years, to improve the electrical discharge machining properties, several trials have been applied with the ultrasonic vibration system which was combined on the sinking electrical discharge machine. In this paper, the effects of the ultrasonic vibration were investigated with the designed sinking EDM machine. Some experimental parameters of tool electrode polarity, rotational workpiece speed and directions were examined during the sinking EDM process on the cemented carbide material of G5. Material removal rate, electrode wear ratio and surface roughness were estimated as the machining properties under finishing machining conditions. The experiments were carried out on ultrasonic longitudinal frequency 59 kHz and electrode spindle till 1,000 rpm. Two rotational apparatuses were used simultaneously on the opposite rotational direction during discharge machining. The discharge conditions were estimated with the waveforms analysis. As the results, the EDM device system which was combined ultrasonic vibration, improved the material removal rate and surface roughness of the EDMed workpiece.

scholarly journals Experimental Study During Electrical Discharge Machining of Reinforced Carbon Fiber Plastic Material

2021 ◽  
Vol 9 (8) ◽  
pp. 1445-1451
Author(s):  
Gaurav Pandey
Keyword(s):  
Surface Roughness ◽  
Carbon Fiber ◽  
Wear Rate ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Fiber Composite ◽  
Electrode Wear ◽  
Machining Parameters

Abstract: The proper selection of machining conditions and machining parameter is an important aspect, before going to machine a carbon-fiber composite material by Die sinking electrical discharge machining (EDM). Because these conditions will determine such important characteristics as; Material removal rate (MRR), Electrode wears rate (EWR), and Surface roughness (R). The purpose of this work is to determine the optimal values of machining parameters of electrical discharge machine, while machining carbon-fiber-composite with copper electrode. The work has been based on the affect of four design factors: pulse current(Ip) supplied by power supply system of electrical discharge machine (EDM), pulse-on-time(TON), gap voltage(Vg) and duty cycle () on such characteristic like material removal rate (MRR), electrode wear rate(EWR), and surface roughness(Ra) on work-piece surface. This work has been done by means of the technique of design of experiment (DOE), which provides us to perform the above-mentioned analysis with small number of experiments. In this work, a L9 orthogonal array is used to design the experiment. The adequate selection of machining parameters is very important in manufacturing system, because these parameters determine the surface quality and dimensional accuracy of the manufactured part. The optimal setting of the parameters are determined through experiments planned, conducted and analyzed using the Taguchi method. It is found that material removal rate (MRR) reduces substantially, within the region of experimentation, if the parameters are set at their lowest values, while the parameters set at their highest values increases electrode wear rate (EWR). Keywords: EDM, Material removal rate, Surface roughness, Tool wear rate,

Effects of Pulse Duration and Current on EDM Process of Allegheny Ludlum D2 Tool Steel

2013 ◽  
Vol 315 ◽  
pp. 369-373
Author(s):  
S. Sulaiman ◽  
A.A. Khan ◽  
M.A. Razak ◽  
M.R. Ibrahim ◽  
M.S. Yusof
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Pulse Duration ◽  
Tool Steel ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Edm Process

The purpose of this paper is to study the effect of current on performance of EDM process of Allegheny Ludlum D2 Tool Steel (UNS T30402). The effect of varying the machining parameters on the machining responses such as material removal rate (MRR), electrode wear rate (EWR), and surface roughness (Ra) have been investigated. In this study, circular shape of copper was used as an electrode with surface area of 100mm². The experiments were repeated for three different values of pulse duration (100µs, 200µs and 400µs) with combination of three different values of discharge current (12A, 16A and 24A). It was found that the pulse duration and current give significant effect on MRR, EWR and Ra. An increase in the pulse durations causes an increase in the MRR and Ra, but a decrease in the EWR. Meanwhile, the effect of currents on EDM performance shows that the increasing currents led to an increase in the MRR, EWR and Ra.

Variation of electrode materials and parameters in the EDM of an AA7075-TiO2 composite

2021 ◽  
Vol 63 (2) ◽  
pp. 182-189
Author(s):  
Sivasamy Alagarsamy ◽  
Manickam Ravichandran
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Electrode Material ◽  
Material Removal ◽  
Pulse Current ◽  
Removal Rate ◽  
Electrode Wear ◽  
Pulse On Time ◽  
Edm Process

Abstract The present study was carried out to analyze the effect of process parameters during EDM machining of AA7075-10 wt.-% TiO2 aluminum matrix composite (AMC). The composite was produced through stir casting. The EDM process parameters such as the electrode material (Cu, Br, EN-8), pulse current (5, 10 and 15 A), pulse ON time (300, 600 and 900 μs) and pulse OFF time (30, 60 and 90 μs) were chosen to study the effects on material removal rate, surface roughness and the electrode wear ratio. The experiment was carried out as per L27 orthogonal array based on Taguchi’s design of experiments. Signal-to-noise ratio and analysis of variance were used to identify the contribution of each input parameters on the output responses of the EDM process. The experimental results shows that pulse ON time and pulse current are the most significant factors for the material removal rate; pulse ON time and electrode material are the most influencing parameters for surface roughness and the electrode wear ratio.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Optimization of μEDM process assisted with rotating magnetic pulling force and ultrasonic vibration

2021 ◽  
pp. 095440892098440
Author(s):  
Gurpreet Singh ◽  
DR Prajapati ◽  
PS Satsangi
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Micro Electrical Discharge Machining ◽  
Pulling Force ◽  
Tool Rotation

The micro-electrical discharge machining process is hindered by low material removal rate and low surface quality, which bound its capability. The assistance of ultrasonic vibration and magnetic pulling force in micro-electrical discharge machining helps to overcome this limitation and increase the stability of the machining process. In the present research, an attempt has been made on Taguchi based GRA optimization for µEDM assisted with ultrasonic vibration and magnetic pulling force while µEDM of SKD-5 die steel with the tubular copper electrode. The process parameters such as ultrasonic vibration, magnetic pulling force, tool rotation, energy and feed rate have been chosen as process variables. Material removal rate and taper of the feature have been selected as response measures. From the experimental study, it has been found that response output measures have been significantly improved by 18% as compared to non assisted µEDM. The best optimal combination of input parameters for improved performance measures were recorded as machining with ultrasonic vibration (U1), 0.25 kgf of magnetic pulling force (M1), 600 rpm of tool rotation (R2), 3.38 mJ of energy (E3) and 1.5 mm/min of Tool feed rate (F3). The confirmation trail was also carried out for the validation of the results attained by Grey Relational Analysis and confirmed that there is a substantial improvement with both assistance applied simultaneously.

Investigation of the Spark Cycle Effect on Material Removal Rate in Wire Electrical Discharge Machining

Manufacturing ◽  
2003 ◽  
Author(s):  
Scott F. Miller ◽  
Albert J. Shih
Keyword(s):  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Short Circuit ◽  
Wire Electrical Discharge Machining ◽  
Time Duration ◽  
Edm Process

The development of new, advanced engineering materials and the needs for precise and flexible prototype and low-volume production have made wire electrical discharge machining (EDM) an important manufacturing process to meet such demand. This research investigates the effect of spark on-time duration and spark on-time ratio, two important EDM process parameters, on the material removal rate (MRR) and surface integrity of four types of advanced material: porous metal foams, metal bond diamond grinding wheels, sintered Nd-Fe-B magnets, and carbon-carbon bipolar plates. An experimental procedure was developed. During the wire EDM, five types of constraints on the MRR due to short circuit, wire breakage, machine slide speed limit, and spark on-time upper and lower limits have been identified. An envelope of feasible EDM process parameters is created and compared across different work-materials. Applications of such process envelope to select process parameters for maximum MRR and for machining of micro features are presented.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

Sign in / Sign up

Export Citation Format

Share Document