Investigation on the effects of ultrasonic vibration on material removal rate and surface roughness in wire electrical discharge turning

2013 ◽  
Vol 70 (5-8) ◽  
pp. 1235-1246 ◽  
Author(s):  
Aminollah Mohammadi ◽  
Alireza Fadaei Tehrani ◽  
Amir Abdullah
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate

Effects of Combined Ultrasonic Vibration during the Sinking EDM Process for Cemented Carbide

2009 ◽  
Vol 76-78 ◽  
pp. 657-663 ◽  
Author(s):  
Chaiya Praneetpongrung ◽  
Yasushi Fukuzawa ◽  
Shigeru Nagasawa
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Cemented Carbide ◽  
Electrode Wear ◽  
Machining Properties ◽  
Edm Process

In recent years, to improve the electrical discharge machining properties, several trials have been applied with the ultrasonic vibration system which was combined on the sinking electrical discharge machine. In this paper, the effects of the ultrasonic vibration were investigated with the designed sinking EDM machine. Some experimental parameters of tool electrode polarity, rotational workpiece speed and directions were examined during the sinking EDM process on the cemented carbide material of G5. Material removal rate, electrode wear ratio and surface roughness were estimated as the machining properties under finishing machining conditions. The experiments were carried out on ultrasonic longitudinal frequency 59 kHz and electrode spindle till 1,000 rpm. Two rotational apparatuses were used simultaneously on the opposite rotational direction during discharge machining. The discharge conditions were estimated with the waveforms analysis. As the results, the EDM device system which was combined ultrasonic vibration, improved the material removal rate and surface roughness of the EDMed workpiece.

Optimization of μEDM process assisted with rotating magnetic pulling force and ultrasonic vibration

2021 ◽  
pp. 095440892098440
Author(s):  
Gurpreet Singh ◽  
DR Prajapati ◽  
PS Satsangi
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Micro Electrical Discharge Machining ◽  
Pulling Force ◽  
Tool Rotation

The micro-electrical discharge machining process is hindered by low material removal rate and low surface quality, which bound its capability. The assistance of ultrasonic vibration and magnetic pulling force in micro-electrical discharge machining helps to overcome this limitation and increase the stability of the machining process. In the present research, an attempt has been made on Taguchi based GRA optimization for µEDM assisted with ultrasonic vibration and magnetic pulling force while µEDM of SKD-5 die steel with the tubular copper electrode. The process parameters such as ultrasonic vibration, magnetic pulling force, tool rotation, energy and feed rate have been chosen as process variables. Material removal rate and taper of the feature have been selected as response measures. From the experimental study, it has been found that response output measures have been significantly improved by 18% as compared to non assisted µEDM. The best optimal combination of input parameters for improved performance measures were recorded as machining with ultrasonic vibration (U1), 0.25 kgf of magnetic pulling force (M1), 600 rpm of tool rotation (R2), 3.38 mJ of energy (E3) and 1.5 mm/min of Tool feed rate (F3). The confirmation trail was also carried out for the validation of the results attained by Grey Relational Analysis and confirmed that there is a substantial improvement with both assistance applied simultaneously.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

scholarly journals Experimental Study During Electrical Discharge Machining of Reinforced Carbon Fiber Plastic Material

2021 ◽  
Vol 9 (8) ◽  
pp. 1445-1451
Author(s):  
Gaurav Pandey
Keyword(s):  
Surface Roughness ◽  
Carbon Fiber ◽  
Wear Rate ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Fiber Composite ◽  
Electrode Wear ◽  
Machining Parameters

Abstract: The proper selection of machining conditions and machining parameter is an important aspect, before going to machine a carbon-fiber composite material by Die sinking electrical discharge machining (EDM). Because these conditions will determine such important characteristics as; Material removal rate (MRR), Electrode wears rate (EWR), and Surface roughness (R). The purpose of this work is to determine the optimal values of machining parameters of electrical discharge machine, while machining carbon-fiber-composite with copper electrode. The work has been based on the affect of four design factors: pulse current(Ip) supplied by power supply system of electrical discharge machine (EDM), pulse-on-time(TON), gap voltage(Vg) and duty cycle () on such characteristic like material removal rate (MRR), electrode wear rate(EWR), and surface roughness(Ra) on work-piece surface. This work has been done by means of the technique of design of experiment (DOE), which provides us to perform the above-mentioned analysis with small number of experiments. In this work, a L9 orthogonal array is used to design the experiment. The adequate selection of machining parameters is very important in manufacturing system, because these parameters determine the surface quality and dimensional accuracy of the manufactured part. The optimal setting of the parameters are determined through experiments planned, conducted and analyzed using the Taguchi method. It is found that material removal rate (MRR) reduces substantially, within the region of experimentation, if the parameters are set at their lowest values, while the parameters set at their highest values increases electrode wear rate (EWR). Keywords: EDM, Material removal rate, Surface roughness, Tool wear rate,

Statistical analysis of material removal rate and surface roughness in electrical discharge turning of titanium alloy (Ti-6Al-4V)

2016 ◽  
Vol 232 (9) ◽  
pp. 1603-1614 ◽  
Author(s):  
Vikas Gohil ◽  
Yogesh M Puri
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Pulse On Time

Electrical discharge turning is a unique form of electrical discharge machining process, which is being especially developed to generate cylindrical forms and helical profiles on the difficult-to-machine materials at both macro and micro levels. A precise submerged rotating spindle as a work holding system was designed and added to a conventional electrical discharge machine to rotate the workpiece. A conductive preshaped strip of copper as a forming tool is fed (reciprocate) continuously against the rotating workpiece; thus, mirror image of the tool is formed on the circumference of the workpiece. The machining performance of electrical discharge turning process is defined and influenced by its machining parameters, which directly affects the quality of the machined component. This study presents an investigation on the effects of the machining parameters, namely, pulse-on time, peak current, gap voltage, spindle speed and flushing pressure, on the material removal rate (MRR) and surface roughness (Ra) in electrical discharge turning of titanium alloy Ti-6Al-4V. This has been done by means of Taguchi’s design of experiment technique. Analysis of variance as well as regression analysis is performed on the experimental data. The signal-to-noise ratio analysis is employed to find the optimal condition. The experimental results indicate that peak current, gap voltage and pulse-on time are the most significant influencing parameters that contribute more than 90% to material removal rate. In the context of Ra, peak current and pulse-on time come up with more than 82% of contribution. Finally, the obtained predicted optimal results were verified experimentally. It was shown that the error values are all less than 6%, confirming the feasibility and effectiveness of the adopted approach.

Sign in / Sign up

Export Citation Format

Share Document