3-D Finite Element Simulation of Friction Stir Welding Process of Non Similar Aluminum-Copper Sheets

2011 ◽  
Vol 312-315 ◽  
pp. 953-958 ◽  
Author(s):  
A. Alimoradi ◽  
M. Loh-Mousavi ◽  
R. Salekrostam
Keyword(s):  
Finite Element ◽  
Friction Stir Welding ◽  
Heat Input ◽  
Three Dimensional ◽  
Welding Process ◽  
Process Conditions ◽  
Friction Stir ◽  
Two Parameters ◽  
Tool Pin ◽  
The Relationship

The Friction Stir Welding (FSW), a relatively new welding process, was developed in 1991 at the Welding Institute near Cambridge, England. There are two tool speeds to be considered in friction-stir welding; how fast the tool rotates and how quickly it traverses the interface. These two parameters have considerable importance and must be chosen with care to ensure a successful and efficient welding cycle. The relationship between the welding speeds and the heat input during welding is complex. In this paper the friction stir welding (FSW) process of stainless steel alloys has been modeled using a three dimensional finite element method. A coupled thermal viscoplastic model was used for the simulation. Tool speeds and temperature distribution are coupled and solved together using this method. The relationship between the welding speeds and the heat input during welding is obtained by numerical analysis, and the stress contour occurred by temperature field and tool force is surveyed. In addition, the effects of FSW process conditions on heating mainly near the tool pin are investigated in this paper.

scholarly journals Technology and equipment for friction stir preweld edge preparation

2021 ◽  
Vol 21 (2) ◽  
pp. 163-170
Author(s):  
Y. G. Lyudmirsky ◽  
А. N. Soloviev ◽  
М. V. Soltovets ◽  
R. R. Kotlyshev ◽  
I. V. Mironov ◽  
...  
Keyword(s):  
Finite Element ◽  
Theoretical Model ◽  
Friction Stir Welding ◽  
Geometric Model ◽  
Three Dimensional ◽  
Welding Process ◽  
Element Model ◽  
Element Mesh ◽  
Laboratory Equipment ◽  
Friction Stir

Introduction. Friction stir welding is widely used due to certain advantages of this method. Factors that reduce the strength of joints made of high-strength aluminum alloys are considered. When welding flat sheets, an effective way to increase the strength of the weld is edge thickening. The paper proposes a method for such thickening. A device is developed, calculations and experiments are carried out. Materials and Methods. Laboratory equipment has been developed to provide simultaneous thickening of two edges to be welded. The main component of this equipment is a steel roller, which is rolled along the edges of two blanks and thickens them due to plastic deformation. The same setup can be used for the friction stir welding process. To calculate the geometry of the thickened edges and the parameters of the deforming roller depending on the value of the edge settlement, a mathematical model based on the contact problem for elastic (roller) and elastoplastic (blank) bodies with a bilinear hardening law has been developed. A three-dimensional simplified geometric model of the facility with account of its symmetry has been constructed. On the contact surfaces, special contact finite elements were selected and the finite element mesh was refined. The numerical implementation of the model was carried out in the ANSYS package. Results. The theoretical model provides assessing the stress-strain state of interacting elements. On the basis of the developed finite element model, the parameters of the thickened edges are calculated, and the geometry of the thickened edges is defined. Using the developed laboratory equipment, full-scale experiments on thickening the edges of the blanks were carried out. The experimental results confirm the adequacy of the developed theoretical model and calculations based on it. The possibility of adjusting the size of the thickened edges is shown.Discussion and Conclusion. A technology for obtaining thickened edges in places of welds is proposed. It will reduce the metal consumption of structures and ensure the bearing capacity of welded joints not lower than similar characteristics of the base metal. A theoretical model of the process is developed, and a numerical experiment providing the selection of the process parameters is carried out. 

scholarly journals The Preliminary Exploration of Micro-Friction Stir Welding Process and Material Flow of Copper and Brass Ultra-Thin Sheets

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2401
Author(s):  
Changqing Zhang ◽  
Zhuo Qin ◽  
Chen Rong ◽  
Wenchen Shi ◽  
Shuwen Wang
Keyword(s):  
Friction Stir Welding ◽  
Flow Behavior ◽  
Pure Copper ◽  
Weld Zone ◽  
Metal Flow ◽  
Welding Process ◽  
Process Conditions ◽  
Friction Stir ◽  
Plastic Metal ◽  
Tool Pin

In the friction stir welding (FSW) of ultra-thin dissimilar metal sheets, different physical material properties, the reduction of plastic metal in the weld zone, and insufficient plastic metal flow lead to poor weld seam shapes and joint qualities. Therefore, it is necessary to study the flow behavior during the FSW of ultrathin sheets. In this study, micro friction stir welding (μFSW) was conducted and analyzed for the butt welding of 0.6-mm-thick ultrathin brass (H62-H) and pure copper (T2-Y) sheets. By analyzing the electric signals of the temperature and force during the welding process, testing the mechanical properties, and analyzing the metallography of the joint, the influences of the process parameters on the metal flow behavior during μFSW were studied. In the proper process conditions, the material preferentially migrated and concentric vortex flow occurred in the vicinity of the shoulder and tool pin action areas. The copper was pushed from the retreating side (RS) to the advancing side (AS) of the weld, allowing it to flow more fully. A mixture of both materials formed at the bottom of the weld nugget, and less migration occurred in the heat-affected zone of the AS at this time. The highest tensile strength can reach 194 MPa, accounting for 82.6% of the copper. The presence of brittle phases Cu5Zn8, AgZn3 and AgZn caused the hardness to fluctuate slightly.

scholarly journals Numerical Simulation of Material Flow and Analysis of Welding Characteristics in Friction Stir Welding Process

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 621 ◽  
Author(s):  
Haitao Luo ◽  
Tingke Wu ◽  
Peng Wang ◽  
Fengqun Zhao ◽  
Haonan Wang ◽  
...  
Keyword(s):  
Finite Element ◽  
Friction Stir Welding ◽  
Finite Element Model ◽  
Material Flow ◽  
Welding Process ◽  
Element Model ◽  
Welding Seam ◽  
Friction Stir ◽  
Tool Pin ◽  
The Finite Element Model

Friction stir welding (FSW) material flow has an important influence on weld formation. The finite element model of the FSW process was established. The axial force and the spindle torque of the welding process were collected through experiments. The feasibility of the finite element model was verified by a data comparison. The temperature field of the welding process was analyzed hierarchically. It was found that the temperature on the advancing side is about 20 °C higher than that on the retreating side near the welding seam, but that the temperature difference between the two sides of the middle and lower layers was decreased. The particle tracking technique was used to study the material flow law in different areas of the weld seam. The results showed that part of the material inside the tool pin was squeezed to the bottom of the workpiece. The material on the upper surface tends to move downward under the influence of the shoulder extrusion, while the material on the lower part moves spirally upward under the influence of the tool pin. The material flow amount of the advancing side is higher than that of the retreating side. The law of material flow reveals the possible causes of the welding defects. It was found that the abnormal flow of materials at a low rotation speed and high welding speed is prone to holes and crack defects. The forming reasons and material flow differences in different regions are studied through the microstructure of the joint cross section. The feasibility of a finite element modeling and simulation analysis is further verified.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Features of structure formation processes in AA2024 alloy joints formed by the friction stir welding with bobbin tool

2021 ◽  
Vol 23 (2) ◽  
pp. 98-115
Author(s):  
Alexey Ivanov ◽  
◽  
Valery Rubtsov ◽  
Andrey Chumaevskii ◽  
Kseniya Osipovich ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Structure Formation ◽  
Welded Joints ◽  
Heat Input ◽  
Welded Joint ◽  
Welding Process ◽  
Tool Material ◽  
Travel Speed ◽  
Material System ◽  
Friction Stir

Introduction. One of friction stir welding types is the bobbin friction stir welding (BFSW) process, which allows to obtain welded joints in various configurations without using a substrate and axial embedding force, as well as to reduce heat loss and temperature gradient across the welded material thickness. This makes the BFSW process effective for welding aluminum alloys, which properties are determined by their structural-phase state. According to research data, the temperature and strain rate of the welded material have some value intervals in which strong defect-free joints are formed. At the same time, much less attention has been paid to the mechanisms of structure formation in the BFSW process. Therefore, to solve the problem of obtaining defect-free and strong welded joints by BFSW, an extended understanding of the basic mechanisms of structure formation in the welding process is required. The aim of this work is to research the mechanisms of structure formation in welded joint of AA2024 alloy obtained by bobbin tool friction stir welding with variation of the welding speed. Results and discussion. Weld formation conditions during BFSW process are determined by heat input into a welded material, its fragmentation and plastic flow around the welding tool, which depend on the ratio of tool rotation speed and tool travel speed. Mechanisms of joint formation are based on a combination of equally important processes of adhesive interaction in “tool-material” system and extrusion of metal into the region behind the welding tool. Combined with heat dissipation conditions and the configuration of the “tool-material” system, this leads to material extrusion from a welded joint and its decompaction. This results in formation of extended defects. Increasing in tool travel speed reduce the specific heat input, but in case of extended joints welding an amount of heat released in joint increases because of specific heat removal conditions. As a result, the conditions of adhesion interaction and extrusion processes change, which leads either to the growth of existing defects or to the formation of new ones. Taking into account the complexity of mechanisms of structure formation in joint obtained by BFSW, an obtaining of defect-free joints implies a necessary usage of various nondestructive testing methods in combination with an adaptive control of technological parameters directly in course of a welding process.

scholarly journals Analysis of the tool plunge in friction stir welding - comparison of aluminium alloys 2024 T3 and 2024 T351

2016 ◽  
Vol 20 (1) ◽  
pp. 247-254
Author(s):  
Darko Veljic ◽  
Bojan Medjo ◽  
Marko Rakin ◽  
Zoran Radosavljevic ◽  
Nikola Bajic
Keyword(s):  
Friction Stir Welding ◽  
Plastic Strain ◽  
Heat Generation ◽  
Aluminium Alloys ◽  
Three Dimensional ◽  
Equivalent Plastic Strain ◽  
Fe Model ◽  
Arbitrary Lagrangian Eulerian ◽  
Friction Stir ◽  
Tool Pin

Temperature, plastic strain and heat generation during the plunge stage of the friction stir welding (FSW) of high-strength aluminium alloys 2024 T3 and 2024 T351 are considered in this work. The plunging of the tool into the material is done at different rotating speeds. A three-dimensional finite element (FE) model for thermomechanical simulation is developed. It is based on arbitrary Lagrangian-Eulerian formulation, and Johnson-Cook material law is used for modelling of material behaviour. From comparison of the numerical results for alloys 2024 T3 and 2024 T351, it can be seen that the former has more intensive heat generation from the plastic deformation, due to its higher strength. Friction heat generation is only slightly different for the two alloys. Therefore, temperatures in the working plate are higher in the alloy 2024 T3 for the same parameters of the plunge stage. Equivalent plastic strain is higher for 2024 T351 alloy, and the highest values are determined under the tool shoulder and around the tool pin. For the alloy 2024 T3, equivalent plastic strain is the highest in the influence zone of the tool pin.

Proposing a new relation for selecting tool pin length in friction stir welding process

Measurement ◽  
2018 ◽  
Vol 129 ◽  
pp. 112-118 ◽  
Author(s):  
Noor Zaman Khan ◽  
Arshad Noor Siddiquee ◽  
Zahid A. Khan
Keyword(s):  
Friction Stir Welding ◽  
Welding Process ◽  
Friction Stir ◽  
Friction Stir Welding Process ◽  
Tool Pin

A Finite Element Model for the Prediction of Chip Formation and Surface Morphology in Friction Stir Welding Process

2021 ◽  
pp. 1-21
Author(s):  
Debtanay Das ◽  
Swarup Bag ◽  
Sukhomay Pal ◽  
M. Ruhul Amin
Keyword(s):  
Finite Element ◽  
Friction Stir Welding ◽  
Surface Morphology ◽  
Chip Formation ◽  
Material Flow ◽  
Welding Process ◽  
Measured Temperature ◽  
Material Loss ◽  
Friction Stir ◽  
Mass Scaling

Abstract Friction stir welding (FSW) is widely recognized green manufacturing process capable of producing good quality welded joints at temperature lower than the melting point. However, most of the works is focused on to the establishment of the process parameters for a defect-free joint. There is a lack to understand the formation of defects from physical basis and visualization of the same, which is otherwise difficult to predict by means of simple experiments. The conventional models do not predict chip formation and surface morphology by accounting the material loss during the process. Hence, a 3D finite element based thermo-mechanical model is developed following Coupled Eulerian-Lagrangian (CEL) approach to understand surface morphology by triggering material flow associated with tool-material interaction. In the present quasi-static analysis, the mass scaling factor is explored to make the model computationally feasible by varying the FSW parameter of plunge depth. The simulated results are validated with experimentally measured temperature and surface morphology. In CEL approach, the material flow out of the workpiece enables the visualization of the chip formation, whereas small deformation predict the surface quality of the joint.

Sign in / Sign up

Export Citation Format

Share Document