Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology

2021 ◽  
pp. 095440622110058
Author(s):  
Sanjeev Verma ◽  
Vinod Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Feed Rate ◽  
Aluminium Alloys ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Industrial Sectors ◽  
Tool Pin

Aluminium and its alloys are lightweight, corrosion-resistant, affordable and high-strength material and find wide applications in shipbuilding, automotive, constructions, aerospace and other industrial sectors. In applications like aerospace, marine and automotive industries, there is a need to join components made of different aluminium alloys, viz. AA6061 and AA5083. In this study friction stir welding (FSW) is used to join dissimilar plates made of AA6061-T6 and AA5083-O. The effect of varying tool pin profile, tool rotation speed, tool feed rate and tilt angle of the tool has been investigated on the tensile strength and percentage elongation of the welded joints. Box-Behkan design, with four input parameters and three levels of each parameter has been employed to decide the set of experimental runs. The regression models have been developed to investigate the influence of welding variables on the tensile strength and elongation of the welded joint. It is revealed that with the increase in welding parameters like tool rpm, tool feed rate and tilt angle of the tool, both the mechanical properties increase, reach a maximum level, followed by a decrease with further increase in the value of parameters. Amongst different types of tool pin profiles used, the FSW tool having straight cylindrical (SC) pin profile is found to yield the maximum strength and elongation of the welded joint for different combinations of welding parameters. Multiple response optimization indicates that the maximum UTS (135.83 MPa) and TE (4.35%) are obtained for the welded joint fabricated using FSW tool having SC pin profile, tilted at 1.11° and operating at tool speed and feed rate of 1568 rpm and 39.53 mm/min., respectively.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

Effect of Tool pin Profile and Axial Force on Tensile Behavior in Friction Stir Welding of Dissimilar Aluminum Alloys

2011 ◽  
Vol 415-417 ◽  
pp. 1140-1146 ◽  
Author(s):  
R. Palanivel ◽  
P. Koshy Mathews ◽  
M. Balakrishnan ◽  
I. Dinaharan ◽  
N. Murugan
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Axial Force ◽  
Aluminium Alloys ◽  
Welding Process ◽  
Fusion Welding ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Dissimilar Aluminum Alloys ◽  
Tool Pin

Aluminium alloys generally has low weldability by traditional fusion welding process. The development of the Friction Stir Welding (FSW) has provided an alternative improved way of producing aluminium joints, in a faster and reliable manner. FSW process has several advantages, in particular the possibility to weld dissimilar aluminium alloys. This study focuses on the behavior of tensile strength of dissimilar joints of AA6351-T6 alloy to AA5083-H111 alloy produced by friction stir welding was analysed. Five different tool pin profile such as Straight Square (SS), Tapered Square (TS), Straight Hexagon (SH), Straight Octagon (SO) and Tapered Octagon (TO) with three different axial force (1tonne, 1.5tonne, 2 tonne) have been used to weld the joints. The effect of pin profiles and axial force on tensile properties and material flow behaviour of the joint was analyzed and it was found that the straight square pin profile with 1.5 tonne produced better tensile strength then other tool pin profile and axial force.

Influences of Tool pin Profile and Tool Shoulder Curvature on the Formation of Friction Stir Welding Zone in AA6061 Aluminium Alloy

2012 ◽  
Vol 445 ◽  
pp. 789-794 ◽  
Author(s):  
Vahid Moosabeiki ◽  
Ghasem Azimi ◽  
Mostafa Ghayoor
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Zone Formation ◽  
Friction Stir ◽  
Tool Pin Profile ◽  
Tool Shoulder ◽  
Aa6061 Aluminium Alloy ◽  
Tool Pin

Friction stir welding (FSW) process is an emerging solid state joining process in which the material that is being welded does not melt and recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters such as tool rotational speed, welding speed, axial force, etc., and tool pin profile play a major role in deciding the weld quality. Friction stir tool plays a major role in friction stir welding process. In this investigation, it is tried to evaluate the effect of tool pin thread and tool shoulder curvature on FSW zone formation in AA6061 aluminium alloy. In this regard, six different tool pin geometries (threadless triangular pin with/without conical shoulder, threaded triangular pin with conical shoulder, threadless square pin with/without conical shoulder, threaded square pin with conical shoulder) are used to fabricate the joints. The formation of FSP zones are analyzed macroscopically. Tensile properties of the joints are evaluated and correlated with the FSP zone formation. Consequently, it is obtained that welding creates a higher quality compared to other tool pin profiles using the square tool with curved shoulder and having threaded pin.

Researching on hybrid friction stir welding between two differential materials as steel and aluminium

2020 ◽  
Vol 3 (SI1) ◽  
pp. First
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Solid State ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Friction Stir ◽  
Hybrid Techniques ◽  
State Process

Friction stir welding exploits its solid-state process behavior to join aluminum to steel, which differs in thermal and mechanical properties, and where a combination of these metallic alloys by fusion welding prompts a deleterious reaction as a result of the melting and resolidification phases. Recently, hybrid techniques have been employed in FSW for several materials and alloys, particularly for steel–steel joining. These methods are generally aimed to pre-heat the steel plate materials. This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between aluminum and steel, and (3) The welding process using stirring friction is simulated. The simulations intended to predict the temperature, which is used for the preheating and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength are carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed, and offset), temperature, and tensile strength. The maximum tensile strength is 77% compared to the strength of the aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving a good quality of the welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in the welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

scholarly journals Temperature Monitoring and Material Flow Characteristics of Friction Stir Welded 2A14-t6 Aerospace Aluminum Alloy

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3387 ◽  
Author(s):  
Tingke Wu ◽  
Fengqun Zhao ◽  
Haitao Luo ◽  
Haonan Wang ◽  
Yuxin Li
Keyword(s):  
Friction Stir Welding ◽  
Material Flow ◽  
Flow Model ◽  
Welding Process ◽  
Temperature Monitoring ◽  
Measuring System ◽  
Welding Parameters ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Tool Pin

Aiming at the problems that the temperature in the welding area of friction stir welding (FSW) is difficult to measure and the joints are prone to defects. Hence, it is particularly important to study the material flow in the welding area and improve the welding quality. The temperature of the tool shoulder and the tool pin was monitored by the wireless temperature measuring system. The finite element model of friction stir welding was established and the welding conditions were numerically simulated. The flow law of material of the friction stir welding process was studied by numerical simulation. The material flow model was established by combining the microstructure analysis results, and the forming mechanism of the defects was analyzed. The results show that the temperature in the welding zone is the highest at 1300 rpm, and the temperature at the tool shoulder is significantly higher than that at the tool pin in the welding stage. When high-rotation speeds (HRS) are chosen, the material beneath the tool shoulder tends to be extruded into the pin stirred zone (PSZ) after flowing back to the advancing side. This will cause turbulence phenomenon in the advancing side of the joint, which will easily lead to the formation of welding defects. In the future, temperature monitoring methods and the flow model of material can be used to optimize the welding parameters.

scholarly journals Effect of process parameters on mechanical properties of AA5052 joints using underwater friction stir welding

2020 ◽  
Vol 14 (1) ◽  
pp. 6259-6271
Author(s):  
Srinivasa Rao Pedapati ◽  
Dhanish Paramaguru ◽  
Mokhtar Awang ◽  
Hamed Mohebbi ◽  
Sharma V Korada
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Welding Process ◽  
Welding Parameters ◽  
Fracture Characterization ◽  
Friction Stir ◽  
Weld Joints ◽  
Underwater Friction Stir Welding

Underwater Friction Stir Welding (UFSW) is a solid-state joining technique which uses a non-consumable tool to weld metals. The objective of this investigation is to evaluate the mechanical properties of the AA5052 Aluminium alloy joints prepared by UFSW. The effect of different type of welding tools and welding parameters on the weld joint properties are studied. Square, tapered cylindrical and taper threaded cylindrical type of welding tools have been used to produce the joints with the tool rotational speed varying from 500 rpm to 2000 rpm while the welding speed varying from 50 mm/min to 150 mm/min. Tensile strength, micro-hardness distribution, fracture features, micro-and macrostructure of the fabricated weld joints have been evaluated. The effect of welding process parameters that influences the mechanical properties and fracture characterization of the joints are explained in detail. A maximum Ultimate Tensile Strength (UTS) value of 222.07 MPa is attained with a gauge elongation of 14.78%. Microstructural evaluation revealed that most of the fracture are found on the thermal mechanically affected zone (TMAZ)adjacent to the weld nugget zone (WNZ) due to bigger grain sizes. It is found that most of the joints exhibit ductile characteristics in failure. Fractography analysis has been used to find the behavior of weld joints in failure.

scholarly journals Influence of material velocity on heat generation during linear welding stage of friction stir welding

2016 ◽  
Vol 20 (5) ◽  
pp. 1693-1701
Author(s):  
Alin Murariu ◽  
Darko Veljic ◽  
Dragana Barjaktarevic ◽  
Marko Rakin ◽  
Nenad Radovic ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Friction Stir Welding ◽  
Heat Generation ◽  
Welding Process ◽  
Slip Rate ◽  
Frictional Heat ◽  
Al Alloy ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Tool Pin

The heat generated during friction stir welding (FSW) process depends on plastic deformation of the material and friction between the tool and the material. In this work, heat generation is analysed with respect to the material velocity around the tool in Al alloy Al2024-T351 plate. The slip rate of the tool relative to the workpiece material is related to the frictional heat generated. The material velocity, on the other hand, is related to the heat generated by plastic deformation. During the welding process, the slippage is the most pronounced on the front part of the tool shoulder. Also, it is higher on the retreating side than on the advancing side. Slip rate in the zone around the tool pin has very low values, almost negligible. In this zone, the heat generation from friction is very low, because the material is in paste-like state and subjected to intensive plastic deformation. The material flow velocity around the pin is higher in the zone around the root of the pin. In the radial direction, this quantity increases from the pin to the periphery of the tool shoulder.

scholarly journals Investigation and development of friction stir welding process for unreinforced polyphenylene sulfide and reinforced polyetheretherketone

2018 ◽  
Vol 32 (9) ◽  
pp. 1242-1267 ◽  
Author(s):  
Hossain Ahmed ◽  
MJL van Tooren ◽  
Jonathan Justice ◽  
Ramy Harik ◽  
Addis Kidane ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Traverse Speed ◽  
Tensile Tests ◽  
Polyphenylene Sulfide ◽  
Analytical Models ◽  
Welding Parameters ◽  
Stress Concentrations ◽  
Friction Stir

The joining of thermoplastics through welding offers numerous advantages over mechanical joining. Most importantly, it eliminates the use of costly fasteners and has only a limited effect on the strength of the parts being joined. Since it does not require the introduction of holes, loading pins, and the associated stress concentrations, a specific form of welding, friction stir welding (FSW), was investigated for the creation of butt joints of unreinforced polyphenylene sulfide (PPS) and short carbon fiber (CF)-reinforced polyetheretherketone (PEEK) plates. Unlike metals, analytical models and experimental results show that the heat generated by the FSW tool is insufficient to produce the heat required to weld thermoplastic materials. Therefore, a second heat source is required for preheating these thermoplastics. In this research, a resistance type surface heater was placed at the bottom of two identical weld pieces to produce good quality welds. Two types of shoulder design such as rotating shoulder and stationary shoulder were developed in this study. Taguchi’s design of experiment method was utilized to develop the welding process, where heating duration, material temperature, tool rotational speed, and tool traverse speed were used as the welding parameters. One of the process parameters, tool traverse speed, had significant influence on the tensile strength of PPS samples. While PPS sample showed relatively lower tensile strength with higher traverse speed, short CF-reinforced PEEK samples had higher tensile strength with a higher traverse speed. In addition to tensile tests, fracture toughness tests were performed for both PPS and PEEK samples to observe the influence of unwelded segments in the welded parts. In this study, joint efficiency of PEEK samples was found to be higher than that of PPS samples. Micrographs of PEEK samples showed uniform homogenous mixture of part materials.

Sign in / Sign up

Export Citation Format

Share Document