Predictive Tool Life Model of CBN in Ti6Al4V High Speed Turning and Cutting Parameter Optimization

2009 ◽  
Vol 407-408 ◽  
pp. 594-598
Author(s):  
Xiao Qin Wang ◽  
Xing Ai ◽  
Jun Zhao ◽  
Pei Quan Guo
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Efficiency ◽  
Predictive Tool ◽  
Cbn Tool ◽  
Small Depth ◽  
Cutting Parameter Optimization

Ti6Al4V is a difficult to machine alloy with low cutting efficiency and server tool wear. A series of orthogonal turning tests with CBN (Cubic Boron Nitride) in higher speed scale was carried out on a CA6140 lathe. The experiential functions of tool life based on orthogonal experiment were developed. The tool wear morphologies were examined by scanning electron microscope (SEM) and energy disperse spectroscopy (EDS), adhesion, diffusion and micro-chipping were the major wear mechanisms of CBN tool. Finally, the cutting parameters of CBN tool in Ti6Al4V dry turning were optimized based on tool life-efficiency contour analysis, in same cutting efficiency, the higher cutting speed and small depth of cut are the better selection, it means that utilization of CBN tool enables the high cutting speed turning of Ti6Al4V.

Tool Life Prediction and Cutting Parameter Optimization for Coated Carbide in Ti6Al4V Turning

2012 ◽  
Vol 426 ◽  
pp. 186-189
Author(s):  
X.Q Wang ◽  
Xing Ai ◽  
Jun Zhao ◽  
X.L. Fu ◽  
Y. Z. Pan
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Carbide Tool ◽  
Contour Analysis ◽  
Cutting Efficiency ◽  
Coated Carbide Tool ◽  
Cutting Parameter Optimization ◽  
Coated Carbide

Ti6Al4V is a difficult to machine alloy with low cutting efficiency and server tool wear. A series of orthogonal turning tests with coated carbide in higher speed scale was carried out on a CA6140 lathe. The experiential functions of tool life based on orthogonal experiment were developed. The tool wear morphologies were examined by scanning electron microscope (SEM) and energy disperse spectroscopy (EDS), adhesion, diffusion and micro-chipping were the major wear mechanisms of coated carbide tool. Finally, the cutting parameters of coated carbide tool in Ti6Al4V dry turning were optimized based on tool life-efficiency contour analysis, in same cutting efficiency, the lower cutting speed and larger depth of cut are the better selection in Ti6Al4V turning for coated carbide tool.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ahsana Aqilah Ahmad ◽  
Jaharah A. Ghani ◽  
Che Hassan Che Haron
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanism ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

Predictive Tool Life Model in Ti6Al4V High Speed Milling and Cutting Parameter Optimization

2010 ◽  
Vol 431-432 ◽  
pp. 257-260
Author(s):  
Xiao Qin Wang ◽  
Xing Ai ◽  
Jun Zhao
Keyword(s):  
Tool Life ◽  
High Speed ◽  
Orthogonal Experiment ◽  
Cutting Parameters ◽  
Contour Analysis ◽  
Cutting Efficiency ◽  
Predictive Tool ◽  
Life Model ◽  
Cutting Parameter Optimization ◽  
Carbide Insert

Ti6Al4V is a difficult to machine alloy with low cutting efficiency and server tool wear. A series of orthogonal milling tests with coated and uncoated carbide insert was carried out. The tool life predictive models based on orthogonal experiment were developed. Finally, the cutting parameters for both tools in Ti6Al4V dry milling were optimized based on tool life-efficiency contour analysis.

Tool Life Analysis when Turning Ti-6Al-4V Using Vegetable Oil-Based Cutting Fluid

2017 ◽  
Vol 882 ◽  
pp. 36-40
Author(s):  
Salah Gariani ◽  
Islam Shyha ◽  
Connor Jackson ◽  
Fawad Inam
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Vegetable Oil ◽  
Flank Wear ◽  
Cutting Speed ◽  
Fractional Factorial ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Tool Flank Wear ◽  
Fluid Concentration

This paper details experimental results when turning Ti-6Al-4V using water-miscible vegetable oil-based cutting fluid. The effects of coolant concentration and working conditions on tool flank wear and tool life were evaluated. L27 fractional factorial Taguchi array was employed. Tool wear (VBB) ranged between 28.8 and 110 µm. The study concluded that a combination of VOs based cutting fluid concentration (10%), low cutting speed (58 m/min), feed rate (0.1mm/rev) and depth of cut (0.75mm) is necessary to minimise VBB. Additionally, it is noted that tool wear was significantly affected by cutting speeds. ANOVA results showed that the cutting fluid concentration is statistically insignificant on tool flank wear. A notable increase in tool life (TL) was recorded when a lower cutting speed was used.

Tool Wear Characteristics in High Speed Milling of Ti-6Al-4V Alloy with Nitrogen Gas Medium

2006 ◽  
Vol 315-316 ◽  
pp. 588-592 ◽  
Author(s):  
Wei Zhao ◽  
Ning He ◽  
Liang Li ◽  
Z.L. Man
Keyword(s):  
Tool Wear ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
Oil Mist ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes

High speed milling experiments using nitrogen-oil-mist as cutting medium were undertaken to investigate the characteristics of tool wear for Ti-6Al-4V Alloy, a kind of important and commonly used titanium alloy in the aerospace and automobile industries. Uncoated carbide tools have been applied in the experiments. The cutting speed was 300 m/min. The axial depth of cut and the radial depth of cut were kept constant at 5.0 mm and 1.0 mm, respectively. The feed per tooth was 0.1 mm/z. Optical and scanning electron microscopes have been utilized to determine the wear mechanisms of the cutting tools, and energy spectrum analysis has been carried out to measure the elements distribution at the worn areas. Meanwhile, comparisons were made to discuss the influence of different cutting media such as nitrogen-oil-mist and air-oil–mist upon the tool wear. The results of this investigation indicate that the tool life in nitrogen-oil-mist is significantly longer than that in air-oil-mist, and nitrogen-oil-mist is more suitable for high speed milling of Ti-6Al-4V alloy than air-oil-mist.

Wear Characteristic and Life of Al2O3/(W,Ti)C Ceramic Tool in Turning Iron-Based P/M Composites

2010 ◽  
Vol 26-28 ◽  
pp. 1052-1055
Author(s):  
Li Fa Han ◽  
Sheng Guan Qu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Empirical Model ◽  
Feed Rate ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Ceramic Tool ◽  
Iron Based

The wear characteristics and life of Al2O3/(W,Ti)C ceramic tool in turning NbCp-reinforced iron-based P/M composites was investigated. Experimental results indicate that cutting parameters have an influence on tool wear, among which cutting speed and depth of cut seem to be more prominent. The maximum flank wear rapidly increases as the increase in cutting speed and depth of cut. While, it increases gradually as the decrease in feed rate. Meanwhile, an empirical model of tool life is established, from which the influence of cutting speed and depth of cut on tool life is far greater than that of feed rate. Also from the empirical model, the preferable range of cutting parameters was obtained.

Tool Wear of Polycrystalline Cubic Boron Nitride Compact Tools in Cutting Hardened Steel

2012 ◽  
Vol 488-489 ◽  
pp. 724-728 ◽  
Author(s):  
Tadahiro Wada
Keyword(s):  
Particle Size ◽  
Boron Nitride ◽  
Tool Wear ◽  
Tool Life ◽  
Cubic Boron Nitride ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Polycrystalline Cubic Boron Nitride ◽  
Cbn Tool ◽  
High Cutting Speed

Using polycrystalline cubic boron nitride compact (cBN) tools, which have different cBN contents and cBN particle sizes, the influences of both the cBN content and the cBN particle size on tool wear in turning of hardened steel at various cutting speeds was experimentally investigated. Three types of cBN tools (a cBN content of 45-55% and 75%, and a cBN particle size of 0.5 μm and 5 μm, respectively) were tested. Furthermore, three kinds of chamfered and honed cutting edges were also used. The main results obtained are as follows: (1) In the case of the cBN tools with the same cBN particle size of 5.0 μm, the tool life of the cBN tool with a cBN content of 75% was longer than that of the cBN tool with a cBN content of 45% at low cutting speed. However, at high cutting speed, the tool life of the cBN tool with a cBN content of 75% was shorter. (2) The tool life of the cBN tool with both a cBN content of 55% and a cBN particle size of 0.5 μm was the longest. (3) The tool wear of cBN tools decreased with a decrease in chamfer width.

scholarly journals Analysis of tool wear and surface roughness in high-speed milling process of aluminum alloy Al6061

2021 ◽  
pp. 71-84
Author(s):  
Nhu-Tung Nguyen ◽  
Dung Hoang Tien ◽  
Nguyen Tien Tung ◽  
Nguyen Duc Luan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Wear ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Milling Process ◽  
Face Milling ◽  
Depth Of Cut ◽  
High Speed Milling

In this study, the influence of cutting parameters and machining time on the tool wear and surface roughness was investigated in high-speed milling process of Al6061 using face carbide inserts. Taguchi experimental matrix (L9) was chosen to design and conduct the experimental research with three input parameters (feed rate, cutting speed, and axial depth of cut). Tool wear (VB) and surface roughness (Ra) after different machining strokes (after 10, 30, and 50 machining strokes) were selected as the output parameters. In almost cases of high-speed face milling process, the most significant factor that influenced on the tool wear was cutting speed (84.94 % after 10 machining strokes, 52.13 % after 30 machining strokes, and 68.58 % after 50 machining strokes), and the most significant factors that influenced on the surface roughness were depth of cut and feed rate (70.54 % after 10 machining strokes, 43.28 % after 30 machining strokes, and 30.97 % after 50 machining strokes for depth of cut. And 22.01 % after 10 machining strokes, 44.39 % after 30 machining strokes, and 66.58 % after 50 machining strokes for feed rate). Linear regression was the most suitable regression of VB and Ra with the determination coefficients (R2) from 88.00 % to 91.99 % for VB, and from 90.24 % to 96.84 % for Ra. These regression models were successfully verified by comparison between predicted and measured results of VB and Ra. Besides, the relationship of VB, Ra, and different machining strokes was also investigated and evaluated. Tool wear, surface roughness models, and their relationship that were found in this study can be used to improve the surface quality and reduce the tool wear in the high-speed face milling of aluminum alloy Al6061

Performance of Brazed Carbide End Mill Tool for Machining of Ti6Al4V

2014 ◽  
Vol 541-542 ◽  
pp. 363-367 ◽  
Author(s):  
Saad Nawaz ◽  
Li Xiao Xing ◽  
Zhou Chai
Keyword(s):  
Tool Wear ◽  
Titanium Alloys ◽  
Tool Life ◽  
Thermal Stresses ◽  
Elevated Temperatures ◽  
Aerospace Industry ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Depth Of Cut ◽  
End Mill

Titanium alloys are attractive materials for aerospace industry due to their exceptional strength to weight ratio that is maintained at elevated temperatures and their good corrosion resistance. Major applications of Titanium alloys were military aerospace industry, but since last decade the trend has now shifted towards commercial industry. On the other hand Titanium alloys are notorious for being poor thermal conductor that leads to them being difficult materials for machining. In this experimental study brazed carbide end mill of grade 5 is used for rough down milling of Ti6Al4V for large depth of cut under different combinations of parameters and application of high pressure coolant. The machining performance was evaluated in terms of tool wear, tool life, thermal crack and tool breaking. The tool wear was mostly observed at the tool tip and at bottom part of tool thermal cracks were observed which propagated with respect to time. Flank wear due to scratching of the cutting chips and diffusion wear because of high thermal stresses were observed specially at the bottom of the cutting tool. At cutting speed of 38m/min tool wear couldnt be observed due to tool failure because of fracture under high thermal stresses. It was found that maximum tool life is obtained at the speed of 25m/min, feed rate of 150mm/min and depth of cut of 10mm. In the end it was concluded that machining of Ti6Al4V is a thermally dominant process which leads to high thermal stresses in machining zone that results in increasing tool wear rate and fracture propagation.

Turning of SAE 1050 Steel With Vegetable Base Cutting Fluid

2012 ◽  
Author(s):  
Rosemar Batista da Silva ◽  
Álisson Rocha Machado ◽  
Déborah de Oliveira Almeida ◽  
Emmanuel O. Ezugwu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Manufacturing Companies ◽  
Machining Performance ◽  
Increase Tool Life

The study of cutting fluid performance in turning is of great importance because its optimization characteristics has associated benefits such as improved tool life and overall quality of machined components as well as reduction in power consumption during machining. However, there are recent concerns with the use of cutting fluids from the environmental and health standpoints. Since environmental legislation has become more rigorous, the option for “green machining” attracts the interest of several manufacturing companies. It is important to consider the cost of machining which is associated with tool wear, depending on the cutting environment. The use of vegetable oil may be an interesting alternative to minimize the health and environmental problems associated with cutting fluids without compromising machining performance. This paper presents a comparative study of mineral and vegetable cutting fluids in terms of tool wear after turning SAE 1050 steel grade with cemented carbide cutting tools. Constant depth of cut of 2mm and variable cutting speed (200 and 350 m/min) and feed rate (0.20 and 0.32 mm/rev) were employed. Test results suggest that is possible to achieve improvement in machinability of the material and increase tool life by using vegetable cutting fluid during machining. Tool life increased by about 85% when machining with vegetable-based fluids compared to mineral-based fluids. Analysis of the worn tools, however, revealed a more uniform wear on the worn flank face when machining with mineral-based fluids.

Sign in / Sign up

Export Citation Format

Share Document