Active Blade Pitch Control for Straight Bladed Darrieus Vertical Axis Wind Turbine of New Design

2013 ◽  
Vol 569-570 ◽  
pp. 668-675 ◽  
Author(s):  
P.D. Chougule ◽  
S.R.K. Nielsen ◽  
Biswajit Basu
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
Pitch Angle ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Stream Tube ◽  
Pitch Control ◽  
Low Wind Speed ◽  
Blade Pitch Angle

As Development of smallvertical axis wind turbines (VAWT) for urban use is becoming an interestingtopic both within industry and academia. However, there are few new designs ofvertical axis turbines which are customized for building integration. These aregetting importance because they operate at low rotational speed producing veryless noise during operation, although these are less efficient than HorizontalAxis Wind Turbines (HAWT). The efficiency of a VAWT has been significantlyimproved by H-Darrieus VAWT design based on double airfoil technology asdemonstrated by the authors in a previous publication. Further, it is well knowthat the variation of the blade pitch angle during the rotation improves thepower efficiency. A blade pitch variation is implemented by active blade pitchcontrol, which operates as per wind speed and position of the blade withrespect to the rotor. A double multiple stream tube method is used to determinethe performance of the H-Darrieus VAWT. The power coefficient is compared withthat of a fixed pitch and a variable pitch double airfoil blade VAWT. It isdemonstrated that an improvement in power coefficient by 20% is achieved andthe turbine could start at low wind speed

The Straight-Bladed Morphing Vertical Axis Wind Turbine

2016 ◽  
Author(s):  
David MacPhee ◽  
Asfaw Beyene
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Low Cost ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Pitch Control ◽  
Control Schemes ◽  
Horizontal Axis Wind Turbines ◽  
Novel Concept

Blade pitch control has been extremely important for the development of Horizontal-Axis Wind Turbines (HAWTs), allowing for greater efficiency over a wider range of operational regimes when compared to rigid-bladed designs. For Vertical-Axis Wind Turbines (VAWTs), blade pitching is inherently more difficult due to a dependence of attack angle on turbine armature location, shaft speed, and wind speed. As a result, there have been very few practical pitch control schemes put forward for VAWTs, which may be a major reason why this wind turbine type enjoys a much lower market share as compared to HAWTs. To alleviate this issue, the flexible, straight-bladed vertical-axis turbine is presented, which can passively adapt its geometry to local aerodynamic loadings and serves as a low-cost blade pitch control strategy increasing efficiency and startup capabilities. Using two-dimensional fluid-structure action simulations, this novel concept is compared to an identical rigid one and is proven to be superior in terms of power coefficient due to decreased torque minima. Moreover, due to the flexible nature of the blades, the morphing turbine achieves less severe oscillatory loadings. As a result, the morphing blade design is expected to not only increase efficiency but also system longevity without additional system costs usually associated with active pitch control schemes.

scholarly journals Experimental and Numerical Investigation on the Performance of Straight-Bladed Vertical Axis Wind Turbine by Adding Cavities to it Structure

2020 ◽  
Vol 26 (4) ◽  
pp. 64-79
Author(s):  
Ahmed Saadi AlJarakh ◽  
Hussain Yousif Mahmood
Keyword(s):  
Wind Speed ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Low Performance ◽  
New Policies ◽  
Energy Harnessing

As the prices of the fuel and power had fluctuated many times in the last decade and new policies appeared and signed by most of the world countries to eliminate global warming and environmental impact on the earth surface and humanity exciting, an urgent need appeared to develop the renewable energy harnessing technologies on the short-term and long-term and one of these promising technologies are the vertical axis wind turbines, and mostly the combined types. The purpose of the present work is to combine a cavity type Savonius with straight bladed Darrieus to eliminate the poor self-starting ability for Darrieus type and low performance for Savonius type and for this purpose, a three-bladed Darrieus type with symmetrical S1046 airfoil was tested experimentally and numerically at different wind speeds (4.5 m/s, 8 m/s and 10 m/s) and it showed a poor self-starting ability at low wind speed although its higher performance at high wind speed. However when adding the cavities in two setup configuration and testing it at the same conditions, it was found that when adding the cavities as reversed cups in the core of the turbine, the performance increased and the power coefficient reached a maximum value at 10 m/s wind speed and it was observed to be 0.0914 , but when the solidity increased by adding three cavities, the performance was higher at low wind speed (4.5 m/s) but it tragically decreased at higher wind speed which indicates that the performance depends on the solidity and the turbine configuration. On the other hand, the numerical simulation showed a good match with the experimental results although it under-predicted the performance.

scholarly journals Blades Optimization for Maximum Power Output of Vertical Axis Wind Turbine

2021 ◽  
Vol 10 (3) ◽  
pp. 585-595
Author(s):  
Ahmad Adnan Shoukat ◽  
Adnan Aslam Noon ◽  
Muhammad Anwar ◽  
Hafiz Waqar Ahmed ◽  
Talha Irfan Khan ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Edge Length ◽  
Research Network ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed ◽  
Edge Profile ◽  
Power Yield

Wind power is a significant and urging sustainable power source asset to petroleum derivatives. Wind machines, for example, H-Darrieus vertical pivot wind turbines (VAWTs) have increased much notoriety in research network throughout the most recent couple of decades because of their applications at destinations having moderately low wind speed. Be that as it may, it is noticed that such wind turbines have low effectiveness. The point of this examination is to plan rotor cutting edges which could create most extreme power yield and execution. Different plan factors, for instance, harmony length, pitch edge, rotor distance across, cutting edge length and pitch point are explored to upgrade the presentation of VAWT. Rotor cutting edges are manufactured using the NACA-0030 structure and tried in wind burrow office and contrast its outcomes and DSM 523 profile. Numerical simulations are performed to get best geometry and stream conduct for achieving greatest power. It is seen that for higher tip-speed-proportion (TSR), shorter harmony length and bigger distance across the rotor (i.e., lower robustness) yields higher effectiveness in NACA 0030. Nevertheless, for lower TSR, the more drawn out agreement length and slighter distance across rotor (i.e., higher strength) gives better implementation. The pitch point is - 2° for TSR = 3 and - 3° for TSR = 2.5. The most extreme power yield of the wind turbine is acquired for the sharp edge profile NACA 0030. Besides, instantaneous control coefficient, power coefficient (CP) is the greatest reason for azimuthal edge of 245° and least esteem for 180°.

Numerical Study of Pitch Angle on H-Type Vertical Axis Wind Turbine

2012 ◽  
Vol 499 ◽  
pp. 259-264
Author(s):  
Qi Yao ◽  
Ying Xue Yao ◽  
Liang Zhou ◽  
S.Y. Zheng
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
Numerical Study ◽  
Vertical Axis ◽  
Azimuth Angle ◽  
Power Coefficient ◽  
Cfd Model ◽  
Vertical Axis Wind Turbine ◽  
Sliding Mesh ◽  
Mesh Technique

This paper presents a simulation study of an H-type vertical axis wind turbine. Two dimensional CFD model using sliding mesh technique was generated to help understand aerodynamics performance of this wind turbine. The effect of the pith angle on H-type vertical axis wind turbine was studied based on the computational model. As a result, this wind turbine could get the maximum power coefficient when pitch angle adjusted to a suited angle, furthermore, the effects of pitch angle and azimuth angle on single blade were investigated. The results will provide theoretical supports on study of variable pitch of wind turbine.

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

scholarly journals Conceptual Design and Structure Analysis of Giromill Vertical Axis Wind Turbine under Low Wind Speed

2020 ◽  
Vol 75 (2) ◽  
pp. 11-19
Author(s):  
Mohamed Saiful Firdaus Hussin ◽  
Mohd Fariduddin Mukhtar ◽  
Mohd Zaidi Mohd Tumari ◽  
Nursabillilah Mohd Ali ◽  
Amir Abdullah Muhammad Damanhuri ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Conceptual Design ◽  
Structure Analysis ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed

scholarly journals Design and Contruction of Vertical Axis Wind Turbine Triple-Stage Savonius Type as the Alternative Wind Power Plant

KnE Energy ◽  
2015 ◽  
Vol 2 (2) ◽  
pp. 172
Author(s):  
Tedy Harsanto ◽  
Haryo Dwi Prananto ◽  
Esmar Budi ◽  
Hadi Nasbey
Keyword(s):  
Wind Speed ◽  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Output Power ◽  
Vertical Axis ◽  
Wind Power Plant ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed ◽  
Simple Materials

<p>A vertical axis wind turbine triple-stage savonius type has been created by using simple materials to generate electricity for the alternative wind power plant. The objective of this research is to design a simple wind turbine which can operate with low wind speed. The turbine was designed by making three savonius rotors and then varied the structure of angle on the three rotors, 0˚, 90˚ and 120˚. The dimension of the three rotors are created equal with each rotor diameter 35 cm and each rotor height 19 cm. The turbine was tested by using blower as the wind sources. Through the measurements obtained the comparisons of output power, rotation of turbine, and the level of efficiency generated by the three variations. The result showed that the turbine with angle of 120˚ operate most optimally because it is able to produce the highest output power and highest rotation of turbine which is 0.346 Watt and 222.7 RPM. </p><p><strong>Keywords</strong>: Output power; savonius turbine; triple-stage; the structure of angle</p>

scholarly journals Double multiple stream tube theory coupled with dynamic stall and wake correction for aerodynamic investigation of vertical axis wind turbine

2020 ◽  
Vol 23 (4) ◽  
pp. 771-780
Author(s):  
Anh Ngoc VU ◽  
Ngoc Son Pham
Keyword(s):  
Wind Turbine ◽  
Shape Function ◽  
Vertical Axis ◽  
Transformation Method ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Stream Tube ◽  
Aerodynamic Investigation

This study describes an effectively analytic methodology to investigate the aerodynamic performance of H vertical axis wind turbine (H-VAWT). An in-house code based on double multiple stream tube theory (DMST) coupled with dynamic stall and wake correction is implemented to estimate the power coefficient. Design optimization of airfoil shape is conducted to study the influences of the dynamic stall and turbulent wakes. Airfoil shape is universally investigated by using the Class/Shape function transformation method. The airfoil study shows that the upper curve tends to be less convex than the lower curve in order to extract more energy of the wind upstream and generate less drag of the blade downstream. The optimal results show that the power coefficient increases by 6.5% with the new airfoil shape.

Optimized Small Vertical Axis Wind Turbine (VAWT), Phase I

2021 ◽  
Author(s):  
Moshe Zilberman ◽  
Abdelaziz Abu Sbaih ◽  
Ibrahim Hadad
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Cost Effective ◽  
Clean Energy ◽  
Vertical Axis ◽  
Low Noise ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Different Types

Abstract Wind energy has become an important resource for the growing demand for clean energy. In 2020 wind energy provided more than 6% of the global electricity demand. It is expected to reach 7% at the end of 2021. The installation growth rate of small wind turbines, though, is relatively slow. The reasons we are interested in the small vertical axis wind turbines are their low noise, environmentally friendly, low installation cost, and capable of being rooftop-mounted. The main goal of the present study is an optimization process towards achieving the optimal cost-effective vertical wind turbine. Thirty wind turbine models were tested under the same conditions in an Azrieli 30 × 30 × 90 cm low-speed wind tunnel at 107,000 Reynolds number. The different types of models were obtained by parametric variations of five basic models, maintaining the same aspect ratio but varying the number of bucket phases, the orientation angles, and the gaps between the vanes. The best performing turbine model was made of one phase with two vanes of non-symmetric bipolynomial profiles that exhibited 0.2 power coefficient, relative to 0.16 and 0.13 that were obtained for symmetrical polynomial and the original Savonius type turbines, respectively. Free rotation, static forces and moments, and dynamic moments and power were measured for the sake of comparison and explanation for the variations in performances of different types of turbines. CFD calculations were used to understand the forces and moment behaviors of the optimized turbine.

Sign in / Sign up

Export Citation Format

Share Document