scholarly journals Experimental and Numerical Investigation on the Performance of Straight-Bladed Vertical Axis Wind Turbine by Adding Cavities to it Structure

2020 ◽  
Vol 26 (4) ◽  
pp. 64-79
Author(s):  
Ahmed Saadi AlJarakh ◽  
Hussain Yousif Mahmood
Keyword(s):  
Wind Speed ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Low Performance ◽  
New Policies ◽  
Energy Harnessing

As the prices of the fuel and power had fluctuated many times in the last decade and new policies appeared and signed by most of the world countries to eliminate global warming and environmental impact on the earth surface and humanity exciting, an urgent need appeared to develop the renewable energy harnessing technologies on the short-term and long-term and one of these promising technologies are the vertical axis wind turbines, and mostly the combined types. The purpose of the present work is to combine a cavity type Savonius with straight bladed Darrieus to eliminate the poor self-starting ability for Darrieus type and low performance for Savonius type and for this purpose, a three-bladed Darrieus type with symmetrical S1046 airfoil was tested experimentally and numerically at different wind speeds (4.5 m/s, 8 m/s and 10 m/s) and it showed a poor self-starting ability at low wind speed although its higher performance at high wind speed. However when adding the cavities in two setup configuration and testing it at the same conditions, it was found that when adding the cavities as reversed cups in the core of the turbine, the performance increased and the power coefficient reached a maximum value at 10 m/s wind speed and it was observed to be 0.0914 , but when the solidity increased by adding three cavities, the performance was higher at low wind speed (4.5 m/s) but it tragically decreased at higher wind speed which indicates that the performance depends on the solidity and the turbine configuration. On the other hand, the numerical simulation showed a good match with the experimental results although it under-predicted the performance.

Wind Energy Harnessing System for Low and High Wind Speeds

2019 ◽  
Author(s):  
Majid Rashidi ◽  
Jaikrishnan R. Kadambi ◽  
Renjie Ke
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
High Speed ◽  
Power Transmission ◽  
Vertical Axis ◽  
Geographic Locations ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Energy Harnessing

Abstract This work presents the design and analysis of a novel wind energy harnessing system that makes use of wind defecting structures to increase the ambient wind speed at geographic locations with relatively low wind speed. The system however reacts to highspeed wind conditions by altering the profile of the wind defecting structure in order to eliminate wind speed amplification attribute of the system, thereby protecting the wind turbine assembly at high speed wind conditions. Although increasing the wind speed is advantageous at geographic locations that the wind speed is typically low; however, from times to time, there could be sustained high-speed wind conditions at the same locations that may damage the wind turbine systems that take advantage of the wind defecting structures. The present work disclosed a wind deflecting structure formed by at least two sail-like partial cylindrical structures that are supported atop of a tower-like foundation in a symmetric arrangement, where one or more wind turbines can be installed in the space between the two partial cylinders. The two partial cylinders, each substantially in form a quarter cylinder is made of plurality of parallel ribbed-like bars, hereafter referred to as “bars” with a flexible thin material that are mechanically supported by the bars. The bars are oriented in a direction perpendicular to the ground; allowing the wing deflecting structures to accept horizonal axis or vertical axis turbines in the space between them. The function of the bars is to allow the thin material, attached to them, to assume a curved configuration substantially in the form of a quarter cylinder. The apparatus is equipped with wind speed monitoring devices, and power source and power transmission means, such as cable-pulleys, chain-sprockets, gears, or mechanical linkages that all work in concert to deploy or stow the thin material along the vertical rods depending to the magnitude of the prevailing wind speed. Preliminary computational fluid dynamics analyses have shown that the wind deflecting structure proposed here in amplifies the wind speed by a factor of 1.65.

Active Blade Pitch Control for Straight Bladed Darrieus Vertical Axis Wind Turbine of New Design

2013 ◽  
Vol 569-570 ◽  
pp. 668-675 ◽  
Author(s):  
P.D. Chougule ◽  
S.R.K. Nielsen ◽  
Biswajit Basu
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
Pitch Angle ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Stream Tube ◽  
Pitch Control ◽  
Low Wind Speed ◽  
Blade Pitch Angle

As Development of smallvertical axis wind turbines (VAWT) for urban use is becoming an interestingtopic both within industry and academia. However, there are few new designs ofvertical axis turbines which are customized for building integration. These aregetting importance because they operate at low rotational speed producing veryless noise during operation, although these are less efficient than HorizontalAxis Wind Turbines (HAWT). The efficiency of a VAWT has been significantlyimproved by H-Darrieus VAWT design based on double airfoil technology asdemonstrated by the authors in a previous publication. Further, it is well knowthat the variation of the blade pitch angle during the rotation improves thepower efficiency. A blade pitch variation is implemented by active blade pitchcontrol, which operates as per wind speed and position of the blade withrespect to the rotor. A double multiple stream tube method is used to determinethe performance of the H-Darrieus VAWT. The power coefficient is compared withthat of a fixed pitch and a variable pitch double airfoil blade VAWT. It isdemonstrated that an improvement in power coefficient by 20% is achieved andthe turbine could start at low wind speed

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

scholarly journals Conceptual Design and Structure Analysis of Giromill Vertical Axis Wind Turbine under Low Wind Speed

2020 ◽  
Vol 75 (2) ◽  
pp. 11-19
Author(s):  
Mohamed Saiful Firdaus Hussin ◽  
Mohd Fariduddin Mukhtar ◽  
Mohd Zaidi Mohd Tumari ◽  
Nursabillilah Mohd Ali ◽  
Amir Abdullah Muhammad Damanhuri ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Conceptual Design ◽  
Structure Analysis ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed

scholarly journals Design and Contruction of Vertical Axis Wind Turbine Triple-Stage Savonius Type as the Alternative Wind Power Plant

KnE Energy ◽  
2015 ◽  
Vol 2 (2) ◽  
pp. 172
Author(s):  
Tedy Harsanto ◽  
Haryo Dwi Prananto ◽  
Esmar Budi ◽  
Hadi Nasbey
Keyword(s):  
Wind Speed ◽  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Output Power ◽  
Vertical Axis ◽  
Wind Power Plant ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed ◽  
Simple Materials

<p>A vertical axis wind turbine triple-stage savonius type has been created by using simple materials to generate electricity for the alternative wind power plant. The objective of this research is to design a simple wind turbine which can operate with low wind speed. The turbine was designed by making three savonius rotors and then varied the structure of angle on the three rotors, 0˚, 90˚ and 120˚. The dimension of the three rotors are created equal with each rotor diameter 35 cm and each rotor height 19 cm. The turbine was tested by using blower as the wind sources. Through the measurements obtained the comparisons of output power, rotation of turbine, and the level of efficiency generated by the three variations. The result showed that the turbine with angle of 120˚ operate most optimally because it is able to produce the highest output power and highest rotation of turbine which is 0.346 Watt and 222.7 RPM. </p><p><strong>Keywords</strong>: Output power; savonius turbine; triple-stage; the structure of angle</p>

scholarly journals Strategies for Enhancing the Low Wind Speed Performance of H-Darrieus Wind Turbine—Part 1

2019 ◽  
Vol 1 (1) ◽  
pp. 185-204 ◽  
Author(s):  
Palanisamy Mohan Kumar ◽  
Krishnamoorthi Sivalingam ◽  
Teik-Cheng Lim ◽  
Seeram Ramakrishna ◽  
He Wei
Keyword(s):  
Wind Speed ◽  
Poor Performance ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Viable Solution ◽  
Speed Performance ◽  
Low Wind Speeds ◽  
Starting Characteristics

Small wind turbines are key devices for micro generation in particular, with a notable contribution to the global wind energy sector. Darrieus turbines, despite being highly efficient among various types of vertical axis turbines, received much less attention due to their starting characteristics and poor performance in low wind speeds. Radically different concepts are proposed as a potential solution to enhance the performance of Darrieus turbine in the weak wind flows, all along the course of Darrieus turbine development. This paper presents a comprehensive review of proposed concepts with the focus set on the low wind speed performance and critically assessing their applicability based on economics, reliability, complexity, and commercialization aspects. The study is first of its kind to consolidate and compare various approaches studied on the Darrieus turbine with the objective of increasing performance at low wind. Most of the evaluated solutions demonstrate better performance only in the limited tip speed ratio, though they improve the low wind speed performance. Several recommendations have been developed based on the evaluated concepts, and we concluded that further critical research is required for a viable solution in making the Darrieus turbine a low speed device.

scholarly journals Conceptual Design and Structure Analysis of Savonius Vertical Axis Wind Turbine under Low Wind Speed

2020 ◽  
Vol 71 (2) ◽  
pp. 178-187
Author(s):  
Mohamed Saiful Firdaus Hussin ◽  
Ridhwan Jumaidin ◽  
Nursabillilah Mohd Ali ◽  
Muhammad Ashraf Fauzi ◽  
Shahrizal Saat ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Conceptual Design ◽  
Structure Analysis ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Low Wind Speed

scholarly journals Optimization of Straight-bladed Darrieus type vertical axis wind blade for low wind speed

2020 ◽  
Vol 211 ◽  
pp. 02008
Author(s):  
Christian M. Mortel ◽  
Nicanor L. Serrano ◽  
John Gabriel G. Decena
Keyword(s):  
Wind Speed ◽  
Optimal Design ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Navier Stokes Equation ◽  
Blade Height ◽  
3D Simulations ◽  
Low Wind Speed ◽  
Design Values ◽  
Blade Geometry

Straight-bladed Darrieus blade is a type of vertical axis wind turbine that requires low wind speed to operate but is considered less efficient due to conventional blade geometry. To increase its performance by means of dynamic torque, the study used a statistical method, central composite design, through DesignExpert software. The computational fluid dynamics (CFD) through SolidWorks Reynolds-Averaged Navier Stokes Equation (RANS) k – epsilon turbulence model was used to simulate the Design of Experiments. The study was composed of two phases, namely 2D and 3D simulations. The 2D simulation studied the effect of varying the camber, camber location, and thickness to the dynamic torque, while the 3D simulation varied the blade height, rotor radius, and materials. The camber’s optimal conditions, camber location, and thickness in 2D simulations are 4.75%, 45%, and 15.50% of the chord, respectively. These optimal design values could reach the dynamic torque equivalent to 60.6571 Newton-meter. Meanwhile, the blade height and rotor radius of the 3D simulations have optimal design values of 4.41 meters and 4.75 meters, respectively. These optimal values could increase the dynamic torque to 2310.01 Newton-meter. The dynamic torque of the optimal design obtained a 133% significant increase compared to the conventional blade. Thus, the research has proven the increase in the Darrieus Wind turbine’s performance by varying its blade geometry.

Sign in / Sign up

Export Citation Format

Share Document