Structural Aspects Revealed by X-Ray Diffraction for Aluminum Alloys 2024 Type

2017 ◽  
Vol 750 ◽  
pp. 20-25
Author(s):  
Florina Violeta Anghelina ◽  
Ionica Ionita ◽  
Dan Nicolae Ungureanu ◽  
Elena Valentina Stoian ◽  
Ileana Nicoleta Popescu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aluminum Alloys ◽  
X Ray Diffraction ◽  
Standard Specification ◽  
2024 Aluminum Alloy ◽  
X Ray ◽  
Wet Chemical ◽  
Fineness Of Grain ◽  
Structural Aspects

This paper presents experimental results revealed on the samples type 2024 aluminum alloy used in aeronautics. Adequate characterization of 2024 aluminum alloys with special destination (aviation) was achieved by combined investigations:(i) wet chemical analysis, (ii) spectrochemical analysis, (iii) X-ray diffraction and (iv) electron microscopy. The main conclusion that emerges from the investigations carried out on aluminum samples revealed that: (a) alloys fits in terms of composition with the standard specification for 2024, in all cases; (b) microstructure vary in fineness of grain, but meets the requirements of aviation rules; the investigated microstructures have been appreciated as adequate of aluminum alloys type "2024".

Microstructural Investigation of Aluminum Alloys Type "2024" for the Aviation Industry

2015 ◽  
Vol 1114 ◽  
pp. 62-67
Author(s):  
Florina Violeta Anghelina ◽  
Vasile Bratu ◽  
Elena Valentina Stoian ◽  
Ileana Nicoleta Popescu
Keyword(s):  
Aluminum Alloys ◽  
Conformity Assessment ◽  
Aviation Industry ◽  
Al Alloy ◽  
Standard Specification ◽  
2024 Aluminum Alloy ◽  
Microstructural Investigation ◽  
Wet Chemical ◽  
Fineness Of Grain

This paper presents experimental results revealed on the samples type 2024 aluminum alloy used in aeronautics. The results of microstructural and compositional investigations presented in this paper were performed on samples taken from 2024 Al alloy samples produced by ALRO Slatina. The main objective of the investigation is the conformity assessment of alloys in terms of chemical composition with the specifications type of aviation [SAE AMS 47N, EN 515, etc]. It also aims microstructural conformity assessment in terms of the grain and the hardening effects by natural or artificial aging applied by the manufacturer. Adequate characterization of 2024 aluminum alloys type was achieved by combined investigations: (i) Wet Chemical Analysis, (ii) Spectrochemical Analysis and (iii) Electron Microscopy. The main conclusion that emerges from the investigations carried out on aluminum samples revealed that: (a) alloys fits in terms of composition with the standard specification for 2024, in all cases; (b) microstructure vary in fineness of grain, but meets the requirements of aviation rules; the investigated microstructures have been appreciated as adequate of aluminum alloys type "2024".

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Detonation Synthesis of Nano-Size Materials

1995 ◽  
Vol 418 ◽  
Author(s):  
J. Forbes ◽  
J. Davis ◽  
C. Wong
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Nucleation And Growth ◽  
Detonation Synthesis ◽  
X Ray Diffraction ◽  
Crystalline Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Nano Size

AbstractThe detonation of explosives typically creates 100's of kbar pressures and 1000's K temperatures. These pressures and temperatures last for only a fraction of a microsecond as the products expand. Nucleation and growth of crystalline materials can occur under these conditions. Recovery of these materials is difficult but can occur in some circumstances. This paper describes the detonation synthesis facility, recovery of nano-size diamond, and plans to synthesize other nano-size materials by modifying the chemical composition of explosive compounds. The characterization of nano-size diamonds by transmission electron microscopy and electron diffraction, X-ray diffraction and Raman spectroscopy will also be reported.

Hydrothermal Synthesis and Characterization of BiFeO3 Polyhedral Crystallites

2012 ◽  
Vol 174-177 ◽  
pp. 508-511
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

BiFeO3 polyhedrons had been successfully synthesized via a hydrothermal method. The as-prepared products were characterized by power X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The possible mechanisms for the formation of BiFeO3 polyhedrons were discussed. Though comparison experiments, it was found that the kind of precursor played a key role on the morphology control of BiFeO3 crystals.

scholarly journals Characterization of ferrite nanoparticles for preparation of biocomposites

2017 ◽  
Vol 8 ◽  
pp. 1257-1265 ◽  
Author(s):  
Urszula Klekotka ◽  
Magdalena Rogowska ◽  
Dariusz Satuła ◽  
Beata Kalska-Szostko
Keyword(s):  
Chemical Method ◽  
Ferrite Nanoparticles ◽  
Chemical Activity ◽  
Nominal Composition ◽  
X Ray Diffraction ◽  
Wet Chemical Method ◽  
X Ray ◽  
Transmission Electron ◽  
Wet Chemical

Ferrite nanoparticles with nominal composition Me0.5Fe2.5O4 (Me = Co, Fe, Ni or Mn) have been successfully prepared by the wet chemical method. The obtained particles have a mean diameter of 11–16 ± 2 nm and were modified to improve their magnetic properties and chemical activity. The surface of the pristine nanoparticles was functionalized afterwards with –COOH and –NH2 groups to obtain a bioactive layer. To achieve our goal, two different modification approaches were realized. In the first one, glutaraldehyde was attached to the nanoparticles as a linker. In the second one, direct bonding of such nanoparticles with a bioparticle was studied. In subsequent steps, the nanoparticles were immobilized with enzymes such as albumin, glucose oxidase, lipase and trypsin as a test bioparticles. The characterization of the nanoparticles was acheived by transmission electron microscopy, X-ray diffraction, energy dispersive X-ray and Mössbauer spectroscopy. The effect of the obtained biocomposites was monitored by Fourier transform infrared spectroscopy. The obtained results show that in some cases the use of glutaraldehyde was crucial (albumin).

Characterization of a coating for radioprotection, by X-ray diffraction, scanning electron microscopy, and dispersive energy spectroscopy

2022 ◽  
Vol 321 ◽  
pp. 126326
Author(s):  
Gladis Aparecida Galindo Reisemberger de Souza ◽  
Ramón Sigifredo Cortés Paredes ◽  
Frieda Saicla Barros ◽  
Gustavo Bavaresco Sucharski ◽  
Sebastião Ribeiro Junior ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

scholarly journals Synthesis and characterization of apatite silicated powders with wet precipitation method

2021 ◽  
Vol 234 ◽  
pp. 00106
Author(s):  
Houda Labjar ◽  
Hassan Chaair
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Analytical Techniques ◽  
Precipitation Method ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wet Precipitation ◽  
Scanning Electron

The synthesis of apatite silicated Ca10(PO4)6-x(SiO4)x(OH)2-x (SiHA) with 0≤x≤2 was investigated using a wet precipitation method followed by heat treatment using calcium carbonate CaCO3 and phosphoric acid H3PO4 and silicon tetraacetate SiC8H20O4 (TEOS) in medium of water ethanol, with three different silicate concentrations. After drying, the samples are ground and then characterized by different analytical techniques like X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning electron Microscopy (SEM) and chemical analysis.

Sign in / Sign up

Export Citation Format

Share Document