Ni0.75Fe0.25 Coated Tubular GDC Anode for Cathode-Supported IT-SOFC with High Anode Porosity

2019 ◽  
Vol 814 ◽  
pp. 457-462
Author(s):  
Hong Xin You ◽  
Lian Peng ◽  
Qiang Wang
Keyword(s):  
Single Cell ◽  
Performance Test ◽  
Three Dimensional ◽  
Impregnation Method ◽  
Composite Anode ◽  
Wet Impregnation ◽  
Gas Channel ◽  
Alloy Particles ◽  
Wet Impregnation Method ◽  
Power Generation Performance

Ni0.75Fe0.25Ox-GDC cermet anode for intermediate temperature solid oxide fuel cell was prepared by hard template method and wet impregnation method. LSC-GDC cathode-supported single cell was fabricated by using Ni0.75Fe0.25 coated tubular GDC as anode for the performance test. The composite anode material with Ni-Fe alloy particles coated tubular GDC was analyzed by XRD and SEM. The maximum power density of the single cell in hydrogen and dry methane was 736 and 400 mW·cm-2 at 800 °C, respectively. The SEM observation showed that the anode had a porous three-dimensional microstructure with high specific surface and rich gas channel, resulting a high power generation performance.

Synthesis and Characterization of MgO/MCM-22 as Catalytic Support Using the Impregnation Technique

2016 ◽  
Vol 881 ◽  
pp. 41-45
Author(s):  
Caroline Vasconcelos Fernandes ◽  
Vitória de Andrade Freire ◽  
Bianca Viana de Sousa
Keyword(s):  
Structural Changes ◽  
Three Dimensional ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
Catalytic Support ◽  
Impregnation Technique ◽  
Xrd Patterns ◽  
Metal Incorporation ◽  
Wet Impregnation Method

MCM-22 is a microporous molecular sieve with a system of sinusoidal three-dimensional channels that do not interconnect themselves, which presents good adsorption capacity and high acidity. Thus, this study aims to evaluate the chemical and structural properties of the catalyst MgO/MCM-22 using wet impregnation method. The synthesis of the zeolite was performed using the static hydrothermal method. Through the XRD patterns, it was possible to observe that the metal incorporation process did not cause structural changes, as well as the analysis showed small peaks related to the magnesium oxide in the structure. The micrographs presented a spherical morphology with depression in the central region. FTIR spectra showed the typical peaks of metal with little differences in the typical peaks of MCM-22.

scholarly journals Nickel-based perovskite catalysts: synthesis and catalytic tests in the production of syngas

Cerâmica ◽  
2018 ◽  
Vol 64 (371) ◽  
pp. 436-442 ◽  
Author(s):  
E. O. Moraes Júnior ◽  
J. O. Leite ◽  
A. G. Santos ◽  
M. J. B. Souza ◽  
A. M. Garrido Pedrosa
Keyword(s):  
Impregnation Method ◽  
X Ray Diffraction ◽  
Organic Precursor ◽  
Wet Impregnation ◽  
Partial Oxidation Reaction ◽  
Conversion Level ◽  
Temperature Programmed ◽  
Perovskite Type ◽  
Wet Impregnation Method ◽  
H2 Selectivity

Abstract La1-xSrxNiO3 (x= 0.0, 0.3 or 0.7) perovskite-type oxides were synthesized using the modified proteic gel method and using collagen as an organic precursor. Catalysts of La1-xSrxNiO3/Al2O3 were obtained using the wet impregnation method. The synthesized catalysts were characterized by X-ray diffraction, surface area and temperature-programmed reduction. The catalysts were evaluated in the partial oxidation reaction of methane, and the levels of selectivity to CO, CO2, H2 and H2O were determined. Among the catalysts studied, the catalyst LaNiO3/Al2O3 had the highest methane conversion level (78%) and higher H2 selectivity (55%).

scholarly journals Catalytic Activity Of Cu/η-Al2O3 Catalysts Prepared From Aluminum Scraps In The NH3-SCO and in the NH3-SCR of NO

2021 ◽  
Author(s):  
Nawel Jr ◽  
Thabet Makhlouf ◽  
Gerard Delahay ◽  
Hassib Tounsi
Keyword(s):  
Catalytic Oxidation ◽  
Catalytic Reduction ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
Reduction Of No ◽  
Evaporation Method ◽  
Nh3 Scr ◽  
Scr Of No ◽  
Selective Catalytic Oxidation ◽  
Wet Impregnation Method

Abstract Copper loaded η-alumina catalysts with different copper contents have been prepared by impregnation/evaporation method. The catalysts were characterized by XRD, FTIR, BET, UV–vis, H2-TPR and evaluated in the selective catalytic reduction of NO by NH3 and in the selective catalytic oxidation of NH3. The characterization techniques showed that the impregnation/evaporation method permits to obtain highly dispersed copper oxide species on the η-alumina surface when low amount of copper is used (1wt. % and 2 wt.%). The wet impregnation method made it possible to reach a well dispersion of the copper species on the surface of the alumina for the low copper contents Cu(1)-Al2O3 and Cu(2)-Al2O3. The latter justifies the similar behavior of Cu(1)-Al2O3) and Cu(2)-Al2O3 in the selective catalytic oxidation of NH3 where these catalysts exhibit a conversion of NH3 to N2 of the order of 100% at T > 500°C.

Effect of CNTs Support Diameter on Pt Particles Size and Distribution

2007 ◽  
Vol 119 ◽  
pp. 231-234
Author(s):  
Yong Hwan Kim ◽  
Yon Ki Seo ◽  
Young Rae Cho ◽  
Kwang Ho Kim ◽  
Won Sub Chung
Keyword(s):  
Electrochemical Impedance ◽  
Pt Catalyst ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
Optimum Diameter ◽  
Electro Oxidation ◽  
Average Size ◽  
Wet Impregnation Method ◽  
Xrd And Tem ◽  
Supported Pt Catalyst

The Platinum catalysts on the carbon nanotubes(CNTs) supports of various diameters were prepared by wet impregnation method using H2PtCl6 precursor. The samples using 100nm, 15~20nm, 10~15nm and 5~10nm diameters of CNTs and carbon nanofibers(CNFs) are named Pt/t- CNFs, Pt/MWNTs20, Pt/MWNTs10 and Pt/MWNTs5, respectively. The effects of CNTs diameter on the Pt particle size and distribution were investigated by the means of powder XRD and TEM observation. In addition, the electro-catalytic characteristics for methanol electro-oxidation were estimated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. The average size of Pt particles increases as follows; Pt/MWNTs10 < Pt/MWNTs5 < Pt/MWNTs20 < Pt/t-CNFs. The electro-catalytic characteristics of Pt/MWNTs10 and Pt/MWNTs20 are found to be superior in comparison with the others. For preparation of the most effective supported Pt catalyst, the optimum diameter of CNTs support in the range of 10-20nm, is needed.

Preparation of Cr Metal Supported on Sulfated Zirconia Catalyst

2019 ◽  
Vol 948 ◽  
pp. 221-227
Author(s):  
Latifah Hauli ◽  
Karna Wijaya ◽  
Ria Armunanto
Keyword(s):  
Sulfated Zirconia ◽  
Reduction Process ◽  
Catalyst Preparation ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
Zirconia Catalyst ◽  
Isotherm Adsorption ◽  
Sulfated Zirconia Catalyst ◽  
Adsorption Desorption ◽  
Wet Impregnation Method

Catalyst of Chromium (Cr) metal supported on sulfated zirconia (SZ) was prepared by wet impregnation method. This study aim to determine the optimal concentration of Cr metal that impregnated on SZ catalyst. Preparation of catalyst was conducted at different concentrations of Cr metal (0.5%, 1%, 1.5% (w/w)), impregnated on SZ catalyst, then followed by the calcinationand reduction process. Catalysts were charaterized by FTIR, XRD, XRF, SAA, TEM, and acidity test. The results showed the Cr/SZ 1% had the highest acidity value of 8.22 mmol/g which confirmed from FTIR spectra. All the crystal phase of these catalysts were in monoclinic. The specific surface area increased with the increasing of Cr metal concentration on SZ catalyst and the isotherm adsorption-desorption of N2 gas observed all the catalysts as mesoporous material. The impregnation process formed particles agglomeration.

scholarly journals {CeO2/Bi2Mo1−xRuxO6} and {Au/Bi2Mo1−xRuxO6} Catalysts for Low-Temperature CO Oxidation

Catalysts ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 947 ◽  
Author(s):  
Edson Edain González ◽  
Ricardo Rangel ◽  
Javier Lara ◽  
Pascual Bartolo-Pérez ◽  
Juan José Alvarado-Gil ◽  
...  
Keyword(s):  
Co Oxidation ◽  
Photoelectron Spectroscopy ◽  
Supported Catalysts ◽  
Pollutant Emissions ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
X Ray ◽  
Low Temperature Co Oxidation ◽  
Carbon Dioxide Co2 ◽  
Wet Impregnation Method

Nowadays, one of the most important challenges that humanity faces is to find alternative ways of reducing pollutant emissions. CeO2/Bi2Mo1−xRuxO6 and Au/Bi2Mo1−xRuxO6 catalysts were prepared to efficiently transform carbon monoxide (CO) to carbon dioxide (CO2) at low temperatures. The systems were prepared in a two-step process. First, Bi2Mo1−xRuxO6 supports were synthesized through the hydrothermal procedure under microwave heating. Then, CeO2 was deposited on Bi2Mo1−xRuxO6 using the wet impregnation method, while the incipient impregnation method was selected to deposit gold nanoparticles. The CeO2/Bi2Mo1−xRuxO6 and Au/Bi2Mo1−xRuxO6 catalysts were characterized using SEM microscopy and XRD. Furthermore, energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy were used. Tests were carried out for the supported catalysts in CO oxidation, and high conversion values, nearing 100%, was observed in a temperature range of 100 to 250 °C. The results showed that the best system was the Au/Bi2Mo0.95Ru0.05O6 catalyst, with CO oxidation starting at 50 °C and reaching 100% conversion at 186 °C.

scholarly journals Deep oxidative desulfurization of model fuels catalysed by immobilized ionic liquid on MIL-100(Fe)

RSC Advances ◽  
2019 ◽  
Vol 9 (38) ◽  
pp. 21804-21809 ◽  
Author(s):  
WanXin Yang ◽  
Guoqing Guo ◽  
Zhihong Mei ◽  
Yinghao Yu
Keyword(s):  
Ionic Liquid ◽  
High Efficiency ◽  
Oxidative Desulfurization ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
Wet Impregnation Method

ILs@MIL-100 composites were synthesized via the wet impregnation method and applied in deep oxidative desulfurization of gasoline with high efficiency.

CeO2 nanodots decorated ketjen black for high performance lithium–sulfur batteries

RSC Advances ◽  
2016 ◽  
Vol 6 (112) ◽  
pp. 111190-111196 ◽  
Author(s):  
Xinye Qian ◽  
Lina Jin ◽  
Lin Zhu ◽  
Shanshan Yao ◽  
Dewei Rao ◽  
...  
Keyword(s):  
High Performance ◽  
Impregnation Method ◽  
Wet Impregnation ◽  
Lithium Sulfur Battery ◽  
Lithium Sulfur Batteries ◽  
Sulfur Battery ◽  
Wet Impregnation Method ◽  
Lithium Sulfur

A CeO2 nanodots decorated ketjen black composite was fabricated by a simple wet impregnation method and used as the host of sulfur for a lithium–sulfur battery.

scholarly journals Oxidative dehydrogenation of isobutane over supported V-Mo mixed oxides

2010 ◽  
Vol 75 (8) ◽  
pp. 1115-1124 ◽  
Author(s):  
Gheorghiţa Mitran ◽  
Ioan-Cezar Marcu ◽  
Adriana Urdă ◽  
Ioan Săndulescu
Keyword(s):  
Oxidative Dehydrogenation ◽  
Mixed Oxides ◽  
Catalytic Performance ◽  
Molybdenum Oxides ◽  
Impregnation Method ◽  
N2 Adsorption ◽  
Wet Impregnation ◽  
Vis Spectroscopy ◽  
Wet Impregnation Method ◽  
Oxidative Dehydrogenation Of Isobutane

Vanadium-molybdenum oxides supported on Al2O3, CeO2 and TiO2 were prepared by a ?wet? impregnation method, characterized using DRX, N2 adsorption, UV-Vis spectroscopy, electrical conductivity measurements and tested in the oxidative dehydrogenation of isobutane. The catalytic performance in the oxidative dehydrogenation of isobutane at 400-550?C depended on the nature of support and on the content of VMoO species on the support. The catalysts supported on alumina were more active and selective than those supported on ceria and titania.

Sign in / Sign up

Export Citation Format

Share Document