Research on Welding Process of Low Alloy High Strength Steel 20MnTiB

2019 ◽  
Vol 815 ◽  
pp. 114-119
Author(s):  
Zhen Liang Li ◽  
Hao Ke ◽  
Yang Shen ◽  
Xi Wang ◽  
Jiao Zhong
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
High Strength Steel ◽  
Welded Joint ◽  
Welding Process ◽  
High Strength ◽  
Post Heat Treatment ◽  
Line Energy ◽  
Metallographic Structure ◽  
Strength Change

In this paper, the properties of the base metal of the low-alloy high-strength steel 20MnTiB, the welding process and the microstructure and properties of the welded joints were studied. The results are as follows: post-heat treatment below 400°C, the strength change of the steel decreases slowly, the elongation does not change significantly, and the metallographic structure is not obvious. When the temperature is above 400, the strength is greatly reduced. And its plasticity increases remarkably, and precipitates on the grain boundary are precipitated and grown on the metallographic structure. When the line energy is in the range of 9.6~12.0kJ/cm, the mechanical properties and microstructure of the welded joints meet the requirements, and the welding process that meets the requirements is studied. Finally, the mechanical properties and microstructure of the welded joint are studied. Provide a reference for the research and application of steel.

Microstructure and Mechanical Properties of Laser Welded Joint of 800 MPa Grade Hot-Rolled High Strength Steel

2019 ◽  
Vol 46 (1) ◽  
pp. 0102002
Author(s):  
环鹏程 Huan Pengcheng ◽  
王晓南 Wang Xiaonan ◽  
朱天才 Zhu Tiancai ◽  
陈文刚 Chen Wengang ◽  
胡增荣 Hu Zengrong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength Steel ◽  
Welded Joint ◽  
High Strength ◽  
Microstructure And Mechanical Properties ◽  
Hot Rolled

Development of High-Strength Steel Plates for Low-Temperature Use

1988 ◽  
Vol 110 (3) ◽  
pp. 171-176
Author(s):  
Y. Nakano ◽  
Y. Saito ◽  
K. Amano ◽  
M. Koda ◽  
Y. Sannomiya ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Yield Strength ◽  
Structural Steel ◽  
Welded Joints ◽  
High Strength Steel ◽  
Control Process ◽  
Charpy Impact ◽  
High Strength ◽  
Steel Plates

This paper describes the metallurgical approaches for producing 415MPa and 460MPa yield strength offshore structural steel plates and the mechanical properties of the steel plates and their welded joints. A thermo-mechanical control process (TMCP) was adopted to manufacture YP415MPa and YP460MPa steel plates with weldability comparable to conventional YP355MPa steel plates. The Charpy impact and CTOD tests of the steel plates and their welded joints proved to be very good.

scholarly journals Mechanical Properties of the Flash Butt Welded Joint of 590MPa High Strength Steel

2007 ◽  
Vol 25 (2) ◽  
pp. 55-61
Author(s):  
Bo-Young Jeong ◽  
In-Su Woo ◽  
Jeong-Kil Kim ◽  
Jong-Bong Lee
Keyword(s):  
Mechanical Properties ◽  
High Strength Steel ◽  
Welded Joint ◽  
High Strength

scholarly journals Underwater Local Cavity Welding of S460N Steel

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5535
Author(s):  
Jacek Tomków ◽  
Anna Janeczek ◽  
Grzegorz Rogalski ◽  
Adrian Wolski
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Standard Deviation ◽  
Welded Joints ◽  
Welded Joint ◽  
Gas Metal Arc Welding ◽  
High Strength ◽  
Carbon Equivalent ◽  
High Porosity ◽  
Weld Porosity

In this paper, a comparison of the mechanical properties of high-strength low-alloy S460N steel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW) process in the air environment and water, by the local cavity welding method. Welded joints were tested following the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant, radiographic, and ultrasonic (phased array) tests were performed. In the next step, the destructive tests, as static tensile-, bending-, impact- metallographic (macroscopic and microscopic) tests, and Vickers HV10 measurements were made. The influence of weld porosity on the mechanical properties of the tested joints was also assessed. The performed tests showed that the tensile strength of the joints manufactured in water (567 MPa) could be similar to the air welded joint (570 MPa). The standard deviations from the measurements were—47 MPa in water and 33 MPa in the air. However, it was also stated that in the case of a complex state of stress, for example, bending, torsional and tensile stresses, the welding imperfections (e.g., pores) significantly decrease the properties of the welded joint. In areas characterized by porosity the tensile strength decreased to 503 MPa. Significant differences were observed for bending tests. During the bending of the underwater welded joint, a smaller bending angle broke the specimen than was the case during the air welded joint bending. Also, the toughness and hardness of joints obtained in both environments were different. The minimum toughness for specimens welded in water was 49 J (in the area characterized by high porosity) and in the air it was 125 J (with a standard deviation of 23 J). The hardness in the heat-affected zone (HAZ) for the underwater joint in the non-tempered area was above 400 HV10 (with a standard deviation of 37 HV10) and for the air joint below 300 HV10 (with a standard deviation of 17 HV10). The performed investigations showed the behavior of S460N steel, which is characterized by a high value of carbon equivalent (CeIIW) 0.464%, during local cavity welding.

Sign in / Sign up

Export Citation Format

Share Document