Effects of Silica Fume Addition on Properties of Fresh Mortar

2021 ◽  
Vol 1023 ◽  
pp. 127-134
Author(s):  
Mizuki Takigawa ◽  
Hiromitsu Koyama ◽  
Yoshiki Uno ◽  
Shigeyuki Date
Keyword(s):  
Silica Fume ◽  
High Strength Concrete ◽  
High Strength ◽  
Plastic Viscosity ◽  
Propagation Characteristics ◽  
Fresh Properties ◽  
Strength Concrete ◽  
Binder Ratio ◽  
Vibration Compaction ◽  
Increasing Demand

In recent years, concrete structures have tended to be taller and larger than before. With that trend, concrete as a material has diversified, and various kinds have been developed to meet differing quality requirements. In particular, the need for high-strength concrete is increasing. In general, high-strength concrete has a low water-binder ratio, so its workability is inferior to general concrete. Including admixtures such as silica fume is one way to remedy this problem. Previous studies have discussed the quality and hardening characteristics achievable using silica fume. Nevertheless, expected increasing demand for high-strength concrete dictates the need to understand not only its properties when fresh, but also to have an accurate picture of its vibration compaction properties on construction sites. In this study, the effect of adding silica fume on the workability of mortar was investigated by evaluating its fresh properties, plastic viscosity, and vibration propagation characteristics. Changes to mortar’s fresh properties due to pressure were also investigated to clarify its behavior in pumping environments. The study confirmed that the addition of silica fume decreases plastic viscosity and increases vibration propagation characteristics, and that increased plastic viscosity due to pressurization can be reduced.

Creep, shrinkage, frost, and sulphate resistance of high strength concrete

1995 ◽  
Vol 22 (3) ◽  
pp. 621-636 ◽  
Author(s):  
Sujit Ghosh ◽  
K. W. Nasser
Keyword(s):  
Fly Ash ◽  
Silica Fume ◽  
Frost Resistance ◽  
High Strength Concrete ◽  
High Strength ◽  
Air Entrainment ◽  
Strength Concrete ◽  
Binder Ratio ◽  
Matrix Morphology ◽  
Creep And Shrinkage

A comprehensive study was undertaken to determine the shrinkage, creep, and durability of high strength concrete (50–70 MPa) containing silica fume and lignite fly ash. The concrete mixtures contained normal CSA type 10 (ASTM type 1) portland cement, 10% condensed silica fume, and different amounts of fly ash that varied between 0 and 80% of the weight of binder in the mixture. The aggregates-to-binder ratio by weight was maintained at 5 and the weight of the superplasticizer was varied between 1.5% and 2.2% of the binder while the water-to-binder ratio was maintained at 0.27. The test program consisted of compressive strength tests at various ages on concrete cylinders; drying shrinkage tests at room temperature; creep tests of sealed and unsealed concrete at room temperature (21 °C (70°F)) and at high temperatures (up to 232 °C (450°F)) under three different stress regimes; frost resistance tests on concrete prisms up to 300 freezing and thawing cycles; and sulphate resistance tests on concrete prisms immersed in 5% Na2SO4 solution for up to 10 months. The results indicated that up to 60% fly ash replacement with 10% silica fume showed either superior or similar 28- and 56-day compressive strengths when compared with the 100% cement control mixture. Fly ash + silica fume concrete indicated lower shrinkage and long-term creep. Creep increased with increase in temperature due to physico-chemical processes, which were confirmed by microstructure analysis using the scanning electron microscope. The creep and shrinkage data of high fly ash + silica fume concrete fitted well to the current ACI creep and shrinkage model. Replacement of cement by up to 35% fly ash and 10% silica fume indicated enhanced frost resistance, without any air-entrainment. The addition of 8% air-entrainment to the 20% fly ash + 10% silica fume mixture increased the durability factor by about 10%. For the 50% fly ash + 10% silica fume mixture, the frost durability factor was found comparable to that of the 100% cement control mixture, and air entrainment did not improve its value appreciably. Sulphate resistance of concrete made with 100% CSA type 10 cement was found satisfactory; however, with increasing fly ash contents (up to 50%), the expansion due to sulphate action was suppressed. A study of matrix morphology and microstructure bonding, using the scanning electron microscope, helped to explain the observed results in a comprehensive manner. Key words: creep, shrinkage, compressive strength, frost resistance, durability factor, sulphate resistance, fly ash, silica fume, high-strength concrete, SEM micrograph, matrix morphology.

Effects of Two Polypropylene Fibers on the Properties of High Strength Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1328-1331
Author(s):  
Bai Rui Zhou ◽  
Dong Dong Han ◽  
Jian Hua Yang ◽  
Yi Liang Peng ◽  
Guo Xin Li
Keyword(s):  
Portland Cement ◽  
Modulus Of Elasticity ◽  
High Strength Concrete ◽  
Polypropylene Fiber ◽  
High Strength ◽  
Polypropylene Fibers ◽  
Strength Concrete ◽  
Reticular Fiber ◽  
Binder Ratio ◽  
Water To Binder Ratio

Portland cement, crushed stone, sand and superplasticizer were used to obtain a high strength concrete with a low water to binder ratio. A reticular polypropylene fiber and a single polypropylene fiber were used to improve the strength of the high strength concrete, but the effects of the two fibers on the slump and strengths were quite different. The reasons of the differences were the surface area and the modulus of elasticity of the fibers. The results show the reticular fiber was better to used in high strength concretes.

Flexural and Splitting Tensile Strength of High Strength Concrete with Diatomite Micro Particles as Mineral Additive

2020 ◽  
Vol 402 ◽  
pp. 50-55 ◽  
Author(s):  
Muttaqin Hasan ◽  
Aulia Desri Datok Riski ◽  
Taufiq Saidi ◽  
Husaini ◽  
Putroe Nadhilah Rahman
Keyword(s):  
Tensile Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Tensile Tests ◽  
Splitting Tensile Strength ◽  
Strength Concrete ◽  
Micro Particles ◽  
Mineral Additive ◽  
Binder Ratio ◽  
Water To Binder Ratio

This paper presents the flexural and splitting tensile strength of high strength concrete (HSC) with diatomite micro particles (DMP) as a mineral additive. In order to have micro particles, the diatomite from Aceh Besar District was ground and sieved with sieve size of 250 mm. The particles were then calcined at the temperature of 600 °C for 5 hours. Four mixtures were designed with different DMP to binder ratio (DMP/b). The ratio was 0%, 5%, 10% and 15%, and the water to binder ratio was 0.3. Four beam specimens with a size of 10 cm × 10 cm × 40 cm and four cylinder-specimens with 10 cm diameter and 20 cm high were prepared for each mixture. Flexural and splitting tensile tests were conducted based on ASTM C78 and ASTM C496/496M. The maximum flexural strength was reached at DMP/b of 5% while the maximum splitting tensile strength was reached at DMP/b of 0%.

Sign in / Sign up

Export Citation Format

Share Document