Surface Roughness Effect on Pseudo-GIXRD Stress Analysis

2005 ◽  
Vol 490-491 ◽  
pp. 153-158
Author(s):  
Jun Peng ◽  
Vincent Ji ◽  
Wilfrid Seiler
Keyword(s):  
Surface Roughness ◽  
Carbon Steel ◽  
Residual Stresses ◽  
Stress Analysis ◽  
Steel Specimen ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
Roughness Effect ◽  
Destructive Analysis ◽  
Non Destructive

Residual stresses levels and their distributions in thin films have an important effect on their mechanical properties. The non-destructive analysis by pseudo-grazing incidence X-ray diffraction (GIXRD) allows us to define residual stresses gradients as a function of thin film depth. In case of pseudo-GXRD, we must take into account the effects due to surface roughness on residual stress analysis. We have investigated firstly a set of carbon steel specimens with different surface roughness (RZ varies from 4.2µm to 9.5µm) obtained by grinding. All specimens were tempered to eliminate the residual stresses due to machining. With K radiation of Chromium, Bragg peak positions were determined with various incidence angles  (varies from 1° to 78°) for each specimen. Secondly, a carbon steel specimen containing 4 zones with different surface roughness was loaded elastically in tension, pseudo-GIXRD has used for stress analysis on the loaded specimen with various incidence angles. The peak shifts due to the surface roughness were studied as function of different roughness and different incidence angles. The stress relaxation due to surface roughness was then studied.

In-Depth Distribution of Stresses Measured by Multireflection Grazing Incidence Diffraction

2013 ◽  
Vol 772 ◽  
pp. 143-147
Author(s):  
Marianna Marciszko ◽  
Andrzej Stanisławczyk ◽  
Andrzej Baczmanski ◽  
Krzysztof Wierzbanowski ◽  
Wilfrid Seiler ◽  
...  
Keyword(s):  
Depth Distribution ◽  
Grazing Incidence ◽  
Inverse Laplace Transform ◽  
Stress Profile ◽  
X Ray Diffraction ◽  
X Ray ◽  
Grazing Incidence Diffraction ◽  
Destructive Analysis ◽  
Sample Range ◽  
Non Destructive

The geometry based on the multireflection grazing incidence X-ray diffraction (called the MGIXD method) can be applied to measure residual stresses. Using this method, it is possible to perform a non-destructive analysis of the heterogeneous stresses for different and well defined volumes below the surface of the sample (range of several mm). As the result the average values of stresses weighted by absorption of X-ray radiation are measured. In this work the stress profile as a function of depth for mechanically polished Ti and Al samples were calculated from MGIXD data using inverse Laplace transform.

scholarly journals Effects of Roughness on Stresses in an Oxide Scale Formed on a Superalloy Substrate

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 479
Author(s):  
Yang Zhao ◽  
Fan Sun ◽  
Peng Jiang ◽  
Yongle Sun
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Residual Stresses ◽  
Oxide Scale ◽  
Rough Surface ◽  
Alumina Scale ◽  
Growth Stress ◽  
Oxide Growth ◽  
Substrate Thickness ◽  
Roughness Effect

The effects of surface roughness on the stresses in an alumina scale formed on a Fecralloy substrate are investigated. Spherical indenters were used to create indents with different radii and depths to represent surface roughness and then the roughness effect was studied comprehensively. It was found that the residual stresses in the alumina scale formed around the rough surface are almost constant and they are dominated by the curvature rather than the depth of the roughness. Oxidation changes the surface roughness. The edge of the indent was sharpened after oxidation and the residual stress there was released presumably due to cracking. The residual stresses in the alumina scale decrease with increase in oxidation time, while the substrate thickness has little effect, given that the substrate is thicker than the alumina scale. Furthermore, the effect of roughness on the oxide growth stress is analysed. This work indicates that the surface roughness should be considered for evaluation of stresses in coatings.

scholarly journals Strategy of Residual Stress Determination on Selective Laser Melted Al Alloy Using XRD

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 451 ◽  
Author(s):  
Yujiong Chen ◽  
Hua Sun ◽  
Zechen Li ◽  
Yi Wu ◽  
Yakai Xiao ◽  
...  
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Residual Stresses ◽  
High Surface ◽  
Al Alloy ◽  
X Ray Diffraction ◽  
Scanning Strategy ◽  
Surface Distribution ◽  
Finished Surface ◽  
Microstructural Morphology

Selective laser melting (SLM) is known to generate large and anisotropic residual stresses in the samples. Accurate measurement of residual stresses on SLM-produced samples is essential for understanding the residual stress build-up mechanism during SLM, while a dramatic fluctuation can be observed in the residual stress values reported in the literature. On the basis of studying the influence of surface roughness on residual stress measured using X-ray diffraction (XRD), we propose a procedure coupling XRD technique with pretreatment consisting of mechanical polishing and chemical etching. The results highlight that residual stresses measured using XRD on as-built SLM-produced samples with high surface roughness are significantly lower than those measured on samples with finished surface, which is due to the stress relaxation on the spiked surface of as-built samples. Surface distribution of residual stresses and the effect of scanning strategy were systematically investigated for SLM-produced AlSi10Mg samples. Microstructural morphology was observed at the interface between sample and building platform and was linked to the surface distribution of residual stresses. This procedure can help us accurately measure the residual stresses in SLM-produced samples and thus better understand its build-up mechanism during the SLM process.

Non-destructive Surface Residual Stress Profiling by Multireflection Grazing Incidence X-Ray Diffraction: a 7050 Al Alloy Study

2020 ◽  
Vol 60 (4) ◽  
pp. 475-480
Author(s):  
V. A. N. Righetti ◽  
T. M. B. Campos ◽  
L. B. Robatto ◽  
R. R. Rego ◽  
G. P. Thim
Keyword(s):  
Residual Stress ◽  
Grazing Incidence ◽  
Al Alloy ◽  
X Ray Diffraction ◽  
Surface Residual Stress ◽  
X Ray ◽  
Non Destructive

Influence of Surface Roughness on the Quality of Data Obtained by Pseudo-Grazing Incidence X-Ray Diffraction

2006 ◽  
Vol 514-516 ◽  
pp. 1618-1622 ◽  
Author(s):  
Maria José Marques ◽  
J.C.P. Pina ◽  
A. Morão Dias
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Stress Gradient ◽  
Roughness Parameter ◽  
Diffraction Method ◽  
Grazing Incidence ◽  
Bragg Diffraction ◽  
X Ray Diffraction ◽  
Residual Surface Stress ◽  
X Ray

The conventional Bragg diffraction geometry, normally used to characterize the residual surface stress state, it is not suitable to evaluate surface treated materials and thin films. The X-ray path lengths through a surface layer or thin film are too short to produce adequate diffraction intensities in relation to the bulk or the substrate. Another limitation of the conventional technique appears when a residual stress gradient is present in the irradiated surface. The technique only enables the evaluation of the mean value of this gradient. In these cases, a recently proposed Pseudo-Grazing Incident X-ray Diffraction method would be better applicable. In this study, the Pseudo-Grazing Incidence X-ray Diffraction is applied to characterize the residual stress depth profiles of several AISI 4140 samples, which were prepared, by mechanical polishing and grinding, in order to present different surface roughness parameters, Ra. The experimental results lead to the conclusion that the surface roughness limits the application of the Pseudo-Grazing Incidence methodology to a minimum X-ray incident angle. This angle is the one that enables a mean X-ray penetration depth with the same order of magnitude of the sample surface roughness parameter, Ra.

Three-dimensional welding residual stresses evaluation based on the eigenstrain methodology via X-ray measurements at the surface

2014 ◽  
Vol 03 (04) ◽  
pp. 1450023
Author(s):  
Masaru Ogawa
Keyword(s):  
Neutron Diffraction ◽  
Residual Stresses ◽  
Three Dimensional ◽  
Strain Gauges ◽  
X Ray Diffraction ◽  
Stress Evaluation ◽  
X Ray ◽  
Residual Strains ◽  
Non Destructive ◽  
Evaluation Accuracy

In order to assure structural integrity for operating welded structures, it is necessary to evaluate crack growth rate and crack propagation direction for each observed crack non-destructively. Here, three dimensional (3D) welding residual stresses must be evaluated to predict crack propagation. Today, X-ray diffraction is used and the ultrasonic method has been proposed as non-destructive method to measure residual stresses. However, it is impossible to determine residual stress distributions in the thickness direction. Although residual stresses through a depth of several tens of millimeters can be evaluated non-destructively by neutron diffraction, it cannot be used as an on-site measurement technique. This is because neutron diffraction is only available in special irradiation facilities. Author pays attention to the bead flush method based on the eigenstrain methodology. In this method, 3D welding residual stresses are calculated by an elastic Finite Element Method (FEM) analysis from eigenstrains which are evaluated by an inverse analysis from released strains by strain gauges in the removal of the reinforcement of the weld. Here, the removal of the excess metal can be regarded as non-destructive treatment because toe of weld which may become crack starters can be eliminated. The effectiveness of the method has been proven for welded plates and pipes even with relatively lower bead height. In actual measurements, stress evaluation accuracy becomes poorer because measured values of strain gauges are affected by processing strains on the machined surface. In the previous studies, the author has developed the bead flush method that is free from the influence of the affecting strains by using residual strains on surface by X-ray diffraction. However, stress evaluation accuracy is not good enough because of relatively poor measurement accuracy of X-ray diffraction. In this study, a method to improve the estimation accuracy of residual stresses in this method is formulated, and it is shown numerically that inner welding residual stresses can be estimated accurately from the residual strains measured by X-ray diffraction.

Sign in / Sign up

Export Citation Format

Share Document