Analysis of 1.4571 Chrome-Nickel Steel Properties after Cold Forming by Bending

2019 ◽  
Vol 952 ◽  
pp. 29-36
Author(s):  
Dana Stančeková ◽  
Mária Michalková ◽  
Milan Sapieta ◽  
Michal Šajgalík ◽  
Miroslav Janota
Keyword(s):  
Heat Treatment ◽  
Plastic Deformation ◽  
Deformation Mechanisms ◽  
Thermal Processes ◽  
Nickel Steel ◽  
Forming Force ◽  
Cold Forming ◽  
Austenitic Structure ◽  
Deformation Processes ◽  
Steel Properties

The paper deals with the problems of austenitic chrome-nickel steels and their behavior in plastic deformation processes. These steels cannot be hardened by thermal processes due to a stable austenitic structure, therefore the increase of strength is achieved only by cold forming. The deformation mechanisms of the slip or twinning are activated by the effect of the forming force in the steel. Mainly, there is formed deformation-induced martensite whose structure is different from the martensite created by the heat treatment. As the intensive hardening of austenitic chrome-nickel steels under the effect of plastic deformation is beneficial, it adversely affects the machining of these materials.

Fatigue Behavior of High Manganese TWIP Steels and of Low Alloy Q&P Steels for Car-Body Applications

2014 ◽  
Vol 783-786 ◽  
pp. 713-720
Author(s):  
Paolo Matteis ◽  
Giorgio Scavino ◽  
R. Sesana ◽  
F. D’Aiuto ◽  
Donato Firrao
Keyword(s):  
Heat Treatment ◽  
Room Temperature ◽  
Fatigue Behavior ◽  
Austenitic Steels ◽  
Fracture Mechanisms ◽  
High Manganese ◽  
Cold Forming ◽  
Austenitic Structure ◽  
Plasticity Effect ◽  
Twip Steels

The automotive TWIP steels are high-Mn austenitic steels, with a relevant C content, which exhibit a promising combination of strength and toughness, arising from the ductile austenitic structure, which is strengthened by C, and from the TWIP (TWinning Induced Plasticity) effect. The microstructure of the low-alloy Q&P steels consists of martensite and austenite and is obtained by the Quenching and Partitioning (Q&P) heat treatment, which consists of: austenitizing; quenching to the Tqtemperature, comprised between Msand Mf; soaking at the Tppartitioning temperature (Tpbeing equal to or slightly higher than Tq) to allow carbon to diffuse from martensite to austenite; and quenching to room temperature. The fatigue behavior of these steels is examined both in the as-fabricated condition and after pre-straining and welding operations, which are representative of the cold forming and assembling operations performed to fabricate the car-bodies. Moreover, the microscopic fracture mechanisms are assessed by means of fractographic examinations.

Research on Spheroidizing Annealing Progress of 38CrMoAl

2014 ◽  
Vol 496-500 ◽  
pp. 51-54
Author(s):  
Yu Hong Yuan ◽  
Zhi Jun Liu ◽  
Wei Gang Zheng ◽  
Shang Jun Zhong
Keyword(s):  
Heat Treatment ◽  
Plastic Deformation ◽  
Experimental Analysis ◽  
Deformation Resistance ◽  
Forming Process ◽  
Cold Forming ◽  
Spheroidizing Annealing

The relationships between microsturcture and cold forming property of 38CrMoAl steel have been studied by experimental analysis investigation. The heat treatment p rocess of guenching cyclic sphereidized annealing for obtaining sturcture with optimum cold forming property was suggested. Through this process the characters with lowerhardness, lower plastic deformation resistance and better processing plastic of the steel can get. the properties of this steel can meet the requirement of cold forming process for materials.

scholarly journals Microstructural Characterization Of Quenched And Plastically Deformed Two-Phase α+β Titanium Alloys

2015 ◽  
Vol 60 (3) ◽  
pp. 2033-2038 ◽  
Author(s):  
M. Motyka ◽  
J. Sieniawski ◽  
W. Ziaja ◽  
G. Mrówka-Nowotnik
Keyword(s):  
Heat Treatment ◽  
Plastic Deformation ◽  
Titanium Alloys ◽  
Thermomechanical Processing ◽  
Microstructural Characterization ◽  
Two Phase ◽  
Deformation Degree ◽  
Plastic Deformation Process ◽  
Deformation Processes

Abstract Development of microstructure in two-phase α+β titanium alloys is realized by thermomechanical processing – sequence of heat treatment and plastic working operations. Analysis of achieved results indicates that hot plastic deformation – depending on deformation degree – causes significant elongation of α phase grains. Following heat treatment and plastic deformation processes lead to their fragmentation and spheroidization. Characterization of microstructure morphology changes during thermomechanical processing of quenched Ti-6Al-4V and Ti-6Al-2Mo-2Cr alloys is presented in the paper. The effect of martensitic phase α’(α”) on microstructure development in plastic deformation process was confirmed.

A comparative study of plastic deformation mechanisms in room-temperature and cryogenically deformed magnesium alloy AZ31

2021 ◽  
Vol 807 ◽  
pp. 140821
Author(s):  
Kai Zhang ◽  
Zhutao Shao ◽  
Christopher S. Daniel ◽  
Mark Turski ◽  
Catalin Pruncu ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Magnesium Alloy ◽  
Comparative Study ◽  
Room Temperature ◽  
Deformation Mechanisms ◽  
Alloy Az31 ◽  
Magnesium Alloy Az31

Structure and Hardness of Cryorolled and Heat-Treated 2xxx Aluminum Alloy

2010 ◽  
Vol 667-669 ◽  
pp. 925-930
Author(s):  
S.V. Krymskiy ◽  
Elena Avtokratova ◽  
M.V. Markushev ◽  
Maxim Yu. Murashkin ◽  
O.S. Sitdikov
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Severe Plastic Deformation ◽  
Coarse Grained ◽  
Aging Response ◽  
Heat Treated ◽  
Aluminum Solid Solution ◽  
A Cell

The effects of severe plastic deformation (SPD) by isothermal rolling at the temperature of liquid nitrogen combined with prior- and post-SPD heat treatment, on microstructure and hardness of Al-4.4%Cu-1.4%Mg-0.7%Mn (D16) alloy were investigated. It was found no nanostructuring even after straining to 75%. Сryodeformation leads to microshear banding and processing the high-density dislocation substructures with a cell size of ~ 100-200 nm. Such a structure remains almost stable under 1 hr annealing up to 200oC and with further temperature increase initially transforms to bimodal with a small fraction of nanograins and then to uniform coarse grained one. It is found the change in the alloy post–SPD aging response leading to more active decomposition of the preliminary supersaturated aluminum solid solution, and to the alloy extra hardening under aging with shorter times and at lower temperatures compared to T6 temper.

Deformation and Heat Treatment of Cold Drawn Gold

2007 ◽  
Vol 550 ◽  
pp. 289-294
Author(s):  
Suk Hoon Kang ◽  
Jae Hyung Cho ◽  
Joon Sub Hwang ◽  
Jong Soo Cho ◽  
Yong Jin Park ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Plastic Deformation ◽  
Mechanical Stability ◽  
Ion Beam ◽  
Quantitative Measure ◽  
Electron Backscattered Diffraction ◽  
Conducting Path ◽  
Deformation And Heat Treatment ◽  
Gold Wires

Cold drawn gold wires are widely applied in electronic packaging process to interconnect micro-electronic components. They basically provides a conducting path for electronic signal transfer, and experience thermo-mechanical loads in use. The mechanical stability of drawn gold wires is a matter of practical concern in the reliable functioning of electronic devices. It is known that mechanical properties of materials are deeply related to the microstructure. With appropriate control of deformation and heat processes, the mechanical properties of final products, such as tensile strength and elongation can be improved. Severe plastic deformation by torsion usually contributes to grain refinement and increment of strength. In this study, microstructure variations with torsion strain followed by drawing and heat treatment were investigated. Analyses by focused ion beam (FIB) and electron backscattered diffraction (EBSD) were carried out to characterize the effect of deformation and heat treatment on the drawn gold wires. Pattern quality of EBSD measurements was used as a quantitative measure for plastic deformation.

Investigations on Microstructure Evolution and Deformation Behavior of Aged and Ultrafine Grained Al-Zn-Mg Alloy Subjected to Severe Plastic Deformation

2010 ◽  
Vol 667-669 ◽  
pp. 253-258
Author(s):  
Wei Ping Hu ◽  
Si Yuan Zhang ◽  
Xiao Yu He ◽  
Zhen Yang Liu ◽  
Rolf Berghammer ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
Microstructure Evolution ◽  
Deformation Behavior ◽  
Deformation Mechanisms ◽  
Mg Alloy ◽  
Ultrafine Grained

An aged Al-5Zn-1.6Mg alloy with fine η' precipitates was grain refined to ~100 nm grain size by severe plastic deformation (SPD). Microstructure evolution during SPD and mechanical behaviour after SPD of the alloy were characterized by electron microscopy and tensile, compression as well as nanoindentation tests. The influence of η' precipitates on microstructure and mechanical properties of ultrafine grained Al-Zn-Mg alloy is discussed with respect to their effect on dislocation configurations and deformation mechanisms during processing of the alloy.

Sign in / Sign up

Export Citation Format

Share Document