Simulation of Temperature Field during Semi-Solid Magnesium Alloy Produced by Casting-Rolling Technology

2008 ◽  
Vol 141-143 ◽  
pp. 671-676
Author(s):  
Song Yang Zhang ◽  
Mao Peng Geng ◽  
Shui Sheng Xie
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Temperature Field ◽  
High Temperature ◽  
Magnesium Alloy ◽  
Experimental Results ◽  
Temperature Fields ◽  
Semi Solid ◽  
Rolling Technology ◽  
Element Method

The temperature fields during semi-solid magnesium alloy produced by casting-rolling technology has been simulated by finite element method on the basis of ANSYS. The temperature fields for different conditions were obtained, which is consistent with the experimental results. Results show that there is a high temperature field in the casting and rolling zone. The temperature fluctuates from the center to edge of the strip near the entry of the casting and rolling zone. but The temperature decreases gradually from the center to edge of the strip near the exit of the casting and rolling zone. There are some remarkable effects of the temperature of the casting and rolling, the velocity of the casting and rolling, the gap of two roll, the cooling of the roll and the diameter of the roll on the temperature field, which are in agreement with the experimental results.

Modeling of Distortion in Girth-Welded Thin Pipes

1990 ◽  
Vol 112 (3) ◽  
pp. 266-272 ◽  
Author(s):  
H. Song ◽  
A. Moshaiov
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
High Temperature ◽  
Qualitative Agreement ◽  
Experimental Results ◽  
Temperature Changes ◽  
Welding Arc ◽  
Element Method

The axisymmetric distortion in girth-welded pipes is studied in this paper. A model is developed based on the fact that only a small part of the pipe near the welding arc undergoes high temperature changes, and thus behaves thermo-elastic-plastically, while the rest of the structure is elastic in nature and may, at most, have some thermo-elastic effects. The model is shown to match Finite Element Method in predicting the overall approximated axisymmetric shrinkage in girth-welded pipes. A qualitative agreement with published analytical and experimental results is achieved as well.

scholarly journals Calculation of temperature fields during lathe machining with thermoelectric cooling by using the finite element method

2019 ◽  
Vol 23 (3 Part B) ◽  
pp. 1889-1899
Author(s):  
Radovan Nikolic ◽  
Miroslav Lucic ◽  
Bogdan Nedic ◽  
Miroslav Radovanovic
Keyword(s):  
Mathematical Model ◽  
Finite Element Method ◽  
Finite Element ◽  
Temperature Field ◽  
Cutting Tool ◽  
Thermoelectric Module ◽  
Temperature Fields ◽  
Prototype Model ◽  
The Finite Element Method ◽  
Element Method

The aim of this work is to explore the possibilities of the implementation of systems based on a thermoelectric module for cooling the cutting tool. This cooling becomes significant when it is not possible to use conventional coolants and lubricants. Starting from existing mathematical models for the calculation of the temperature field of the cutting tool, a mathematical model is developed that takes into account the cooling based on the thermoelectric module. The use of the finite element method determines temperature field when dry lathe machining in the cooling conditions based on the thermoelectric module. The Software package, PAK-T, is used for the calculations and was developed at the Department of Applied Mechanics, Faculty of Engineering in Kragujevac, Serbia. The system for cooling the cutting tool based on the thermoelectric module was realized under laboratory conditions on a prototype model, which consists of a cutting tool and a thermoelectric module. Verification of the obtained results was carried out on the basis of a mathematical model by experimental research of the temperature field of the cutting tool in terms of cooling based on a thermoelectric module.

Numerical Simulation of Semi-Solid AZ91D Magnesium Alloy in Thixoforming Process

2008 ◽  
Vol 141-143 ◽  
pp. 505-510
Author(s):  
Ze Sheng Ji ◽  
Hong Hua Yan ◽  
Mao Liang Hu ◽  
Xiao Ping Zheng
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Constitutive Relations ◽  
Metal Flow ◽  
Stress Strain ◽  
Finite Element Software ◽  
Az91d Magnesium Alloy ◽  
Semi Solid ◽  
Element Method

In the process of metal plastic forming severe plastic deformations occur to the workpiece. As a result the constitutive relations between material and geometry are nonlinear. One of the most common tools to solve such problems is the finite element method. In thixoforming processes of semi-solid metal many factors affect thixoforming fluidity. Therefore it is important to simplify the problem and predict the metal flow properties. For that reason the thixoforming process of semi-solid AZ91D magnesium alloy was modeled with the theory of rigid viscoplastic finite element method using the commercial finite element software DEFORM-3DTM. The fluid and effective stress-strain fields in the thixoforming process were obtained and the relationships among stress, strain rate and temperature were analyzed.

Temperature Field Simulation Analysis of High Temperature Box

2011 ◽  
Vol 211-212 ◽  
pp. 925-929
Author(s):  
Wen Xue Qian ◽  
Xiao Wei Yin ◽  
Li Yang Xie
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Temperature Field ◽  
High Temperature ◽  
Thermal Field ◽  
Simulation Analysis ◽  
Field Simulation ◽  
Result Show ◽  
Design Objects ◽  
Element Method

High temperature box is wildly used in many fields. Alone with the increasing of the requirement temperature, the temperature of it becomes more and more high. But it is difficult to test the temperature when the temperature is greater than 2000°C. In this paper, the thermal field of high temperature box is analyzed by finite element method, the result show that the temperature satisfies the design objects.

A Study on Extrusion Deformation Behavior of ZAM631 Magnesium Alloy Using the Rigid Plastic Finite Element Method

2015 ◽  
Vol 53 (8) ◽  
pp. 569-577 ◽  
Author(s):  
Kwang Shin ◽  
Ki Soon Choi ◽  
Ji Hoon Hwang ◽  
Kyunghoon Lee
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Deformation Behavior ◽  
Rigid Plastic ◽  
Element Method

Tire Cornering Simulation Using an Explicit Finite Element Analysis Code

1998 ◽  
Vol 26 (2) ◽  
pp. 109-119 ◽  
Author(s):  
M. Koishi ◽  
K. Kabe ◽  
M. Shiratori
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Test System ◽  
Experimental Results ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Explicit Finite Element ◽  
Explicit Finite Element Analysis ◽  
Element Method

Abstract The finite element method has been used widely in tire engineering. Most tire simulations using the finite element method are static analyses, because tires are very complex nonlinear structures. Recently, transient phenomena have been studied with explicit finite element analysis codes. In this paper, the authors demonstrate the feasibility of tire cornering simulation using an explicit finite element code, PAM-SHOCK. First, we propose the cornering simulation using the explicit finite element analysis code. To demonstrate the efficiency of the proposed simulation, computed cornering forces for a 175SR14 tire are compared with experimental results from an MTS Flat-Trac Tire Test System. The computed cornering forces agree well with experimental results. After that, parametric studies are conducted by using the proposed simulation.

scholarly journals Experimental Results of SiC reinforced Al2O3 Matrix Ceramic Matrix Composites Validated with Finite Element Method

2019 ◽  
Vol 8 (12) ◽  
pp. 307-310
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Ceramic Matrix Composites ◽  
Experimental Results ◽  
Matrix Composites ◽  
Metal Oxidation ◽  
Element Analysis ◽  
Advanced Analysis ◽  
Al2o3 Matrix ◽  
Element Method

In this paper, SiCp /Al2O3 composites were fabricated through directed metal oxidation process. Experimental results of these composites validated or compared with Finite Element Method (FEM). Finite Element has become one in all the foremost necessary tools offered to an engineer. The finite part methodology is employed to resolve advanced analysis issues. In this paper, Finite Element Method based ANSYS software is used to FEM model to determine mechanical properties of SiC reinforced Al2O3 matrix composite by changing volume fractions of SiC. The comparison of experimental results with Finite element analysis provides detailed information about the results of these comparisons. The FA was competent of predict the information for several scenario quite fine

Finite Element Method (FEM) modeling of the powder compaction of cosmetic products: Comparison between simulated and experimental results

2012 ◽  
Vol 224 ◽  
pp. 233-240 ◽  
Author(s):  
H. Diarra ◽  
V. Mazel ◽  
A. Boillon ◽  
L. Rehault ◽  
V. Busignies ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Powder Compaction ◽  
Experimental Results ◽  
Cosmetic Products ◽  
Fem Modeling ◽  
Element Method
Sign in / Sign up

Export Citation Format

Share Document