scholarly journals Does the temperature of beverages affect the surface roughness, hardness, and color stability of a composite resin?

2013 ◽  
Vol 07 (02) ◽  
pp. 165-171 ◽  
Author(s):  
Duygu Tuncer ◽  
Emel Karaman ◽  
Esra Firat
Keyword(s):  
Surface Roughness ◽  
Composite Resin ◽  
Color Change ◽  
Artificial Saliva ◽  
Color Stability ◽  
The Other ◽  
Control Group ◽  
Baseline Values ◽  
Hardness Values ◽  
Properties Of Composites

ABSTRACT Objective: To investigate the effect of beverages′ temperature on the surface roughness, hardness, and color stability of a composite resin. Materials and Methods: Fifty specimens of the Filtek Z250 composite (3M ESPE, Dental Products, St.Paul, MN, USA) were prepared and initial roughness, microhardness, and color were measured. Then the specimens were randomly divided into five groups of 10 specimens each: Coffee at 70°C, coffee at 37°C, cola at 10°C, cola at 37°C, and artificial saliva (control). After the samples were subjected to 15 min × 3 cycles per day of exposure to the solutions for 30 days, the final measurements were recorded. Results: After immersion in beverages, the artificial saliva group showed hardness values higher than those of the other groups (P < 0.001) and the microhardness values were significantly different from the initial values in all groups except for the control group. Both cola groups showed roughness values higher than the baseline values (P < 0.05), while the other groups showed values similar to the baseline measurements. When ΔE measurements were examined, the 70°C coffee group showed the highest color change among all the groups (P < 0.05). Conclusion: High-temperature solutions caused alterations in certain properties of composites, such as increased color change, although they did not affect the hardness or roughness of the composite resin material tested.

Effects of Immersion Media and Repolishing on Color Stability and Superficial Morphology of Nanofilled Composite Resin

2014 ◽  
Vol 20 (4) ◽  
pp. 1234-1239 ◽  
Author(s):  
Ana Luísa Botta Martins de Oliveira ◽  
Ana Carolina Botta ◽  
Juliana Álvares Duarte Bonini Campos ◽  
Patrícia Petromilli Nordi Sasso Garcia
Keyword(s):  
Statistical Difference ◽  
Composite Resin ◽  
Color Change ◽  
Artificial Saliva ◽  
Color Stability ◽  
Color Reading ◽  
Immersion Medium ◽  
Mixed Analysis ◽  
Mouth Rinses ◽  
Scanning Electron

AbstractThis study evaluated the influence of fluoride mouth rinses and repolishing on the superficial morphology and color stability of nanofilled resin. About 150 specimens were prepared and polished using aluminum oxide discs for 15 s with a pressure of 2 kg. The experimental groups were divided according to the immersion medium (artificial saliva, 0.5% sodium fluoride, Fluordent Reach, Oral B, Fluorgard) and repolishing procedure (without and with). The specimens were continuously immersed for 1 week. Thereafter, half of each sample was repolished. A color reading was performed after 24 h of immersion in the artificial saliva baseline, after continuous immersion, and after repolishing. The superficial morphology was examined using scanning electron microscopy (SEM) in a qualitative way. Color change (∆E) data were submitted to a mixed analysis of variance using a Shapiro–Wilk test (p>0.05 for the different immersion media) and Sidak’s test (p<0.05 for the differences between groups). In the interaction between the repolishing and the immersion media, Fluorgard showed a statistical difference between the ∆E values with and without repolishing (p<0.0001). On the SEM observations, both Fluordent Reach and Fluorgard caused degradation of the superficial resinous matrix of the composite after continuous immersion. This matrix was removed after repolishing.

scholarly journals Quantification of color variation of restorative materials used on pediatric dentistry after pigmentation

2015 ◽  
Vol 63 (4) ◽  
pp. 383-388
Author(s):  
Luísa Bandeira Pires Monteiro LOPES ◽  
Andreia Sofia Lopes de ARAÚJO ◽  
Virginia Barreiros MILAGRE
Keyword(s):  
Composite Resin ◽  
Color Change ◽  
Artificial Saliva ◽  
Pediatric Dentistry ◽  
Color Variation ◽  
Control Group ◽  
Chocolate Milk ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Restorative Materials

Objective: To quantify the color variation of two glass ionomer cements and a composite resin used in pediatric dentistry, after being immersed in different pigments agents. Methods: Using two glass ionomer cements (Ketac(tm) Molar and Photac(tm) Fil) and a microhybrid composite resin (Filtek(tm) z250), were produced 40 disks of each material (10 mm in diameter and 2 mm thick). The samples were soaked in artificial saliva (control group), coke, peach Ice Tea(r) and chocolate milk, for 72 hours in an oven at 37ºC. After this period, the samples were washed in 50 ml of distilled water. Finally, using the spectrophotometer, it was made the reading of results. The color change was measured according to the CIE L * a * b * system. Color changes were statistically analyzed using parametric one-way ANOVA and ANOVA with Welch correction, the nonparametric Kruskal-Wallis tests and post-hoc Tukey and Dunnet T3 with p≤ 0.05. Results: The immersion of restorative materials in different pigmentation agents caused a significant color variation on the samples. The agent who presented higher results was the Peach Ice Tea(r). The chocolate milk was the fluid with lowest pigmentation capacity of all restorative materials under study. The greater color variation was found on the Ketac(tm) Molar submerged in Coca-Cola(r) and the smallest on the Filtek(tm) z250 in chocolate milk. Conclusion: All restorative materials were shown to be susceptible to pigmentation by all agents. The Filtek(tm) z250 proved to have better color stability, followed by Photac(tm) Fil and finally by Ketac(tm) Molar.

scholarly journals Roughness and stability of compound resin color exposed to bleaching strips after surface treatment

2020 ◽  
Vol 68 ◽  
Author(s):  
Izabelle Fiamma Alves Pessoa Matias CALIXTO ◽  
Michelly Rodrigues Dantas GAMA ◽  
Júlia Peixoto CAMPOS ◽  
Celina Wanderley de ABREU ◽  
Lucas Lactim FERRAREZ ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Treatment ◽  
Composite Resin ◽  
Color Change ◽  
Color Stability ◽  
System L ◽  
Significant Difference ◽  
Subsequent Exposure ◽  
Cielab System ◽  
Level Of Significance

ABSTRACT Objective to analyze the surface roughness and color stability of the composite resin after surface treatment with the aluminum oxide discs and subsequent exposure to the Advanced Teeth Whitening Strips. Methods 20 specimens of the Filtek Z350XT restorer (3M®) were prepared and daily subjected to home bleaching for 30 minutes during 14 days. A precision rugosimeter was used in order to verify the roughness by means of 3 random readings in the same direction in each sample. For color stability the CIELAB system (L*, a*, b* values) was used through the spectrophotometer (MINOLTA CR -321, Japan). The means of the test specimens as well as the mean of each group were calculated using the random readings. Data statistical analysis were performed by ANOVA- analysis of variance. The level of significance was set at 5% (p ≤ 0.05). Results Roughness did not present great numerical variations. No statistically significant difference between the means obtained concerning the surface roughness of the composite resin with p = 0.44 was observed. However, it was found that there was a statistically significant difference between the means obtained in relation to the color stability of the composite resin, p=0. 007. Conclusion It was concluded that pre-contoured strips containing 6% hydrogen peroxide do not have a significant adverse effect on the roughness of Z350XT (3M®) resin. However, it was also concluded that according to the color stability analysis performed, there may be an indication of the restoration replacement after the bleaching treatment, due to their color change.

scholarly journals Effect of a Prebrushing Mouthwash on Color Stability of Composite Resins

2021 ◽  
Vol 22 (3) ◽  
pp. 191-194
Author(s):  
Ângela Dalla Nora ◽  
Camila da Silva Rodrigues ◽  
Rachel de Oliveira Rocha
Keyword(s):  
Composite Resin ◽  
Color Change ◽  
Test Group ◽  
Color Stability ◽  
Composite Resins ◽  
Control Group ◽  
Water Control ◽  
Dental Tissues ◽  
Evaluation Time ◽  
Materials Used

AbstractDespite composite resins capacity to mimic dental tissues, they can discolor over time. However, there is no information on the effect of prebrushing mouthwashes on the composite resin staining. This study aimed to evaluate the effect of prebrushing mouthwashes on the color stability of three composite resins. Twenty specimens of each resin were prepared: Filtek Z250 (3M ESPE –S Paul, MN, USA), Charisma (Heraeus Kulzer GmbH - Hanau - Germany) e EvoluX (Dentsply- Petrópolis - Brazil). Groups were randomly divided accord to the treatment: immersion in prebrushing mouthwash (test group) or immersion in deionized water (control group). Test groups were immersed in 10 ml of prebrushing mouthwash Plax Magic (Colgate-Palmolive, São Bernardo do Campo, SP, Brazil) for 60 s three times a day during 35 days following the manufacturer’s instructions. Color measurements were performed after 24 h of specimen’s preparation and after 7, 14, 21, and 35 days of immersion time. Results showed that prebrushing mouthwash Plax Magic promoted a color change in all the tested materials and evaluation time. The color change was greater in composite resin Charisma, followed by Z250 and EvoluX. Therefore, prebrushing mouthwash promoted a color change in all the materials used. Composite resin Charisma demonstrated less color stability than Filtek Z250 resin and EvoluX resin, which was the most stable.Keywords: Composite Resins. Oral Hygiene. Color.ResumoApesar da capacidade das resinas compostas de mimetizar os tecidos dentais, esses materiais podem ter sua cor alterada com o tempo. No entanto, não há informação na literatura sobre o efeito de evidenciadores de placa na estabilidade de cor desses materiais. Este estudo teve por objetivo avaliar o efeito de um evidenciador de placa na estabilidade de cor e três resinas compostas. Para isso, 20 espécimes de cada resina foram preparados: Filtek Z250 (3M ESPE –S Paul, MN, EUA), Charisma (Heraeus Kulzer GmbH - Hanau - Alemanha) e EvoluX (Dentsply- Petrópolis - Brasil). Os grupos foram aleatoriamente divididos de acordo com o tratamento a ser submetido: imersão no evidenciador de placa (grupo teste) ou imersão em água deionizada (grupo controle). Os grupos teste foram imersos em 10 ml do evidenciador de placa Plax Magic (Colgate-Palmolive, São Bernardo do Campo, SP, Brasil) por 60 s três vezes por dia durante 35 dias, de acordo com a orientações de uso do fabricante. As leituras de cor foram feitas após 24 h da preparação dos espécimes e após 7, 14, 21 e 35 dias de imersão. Os resultados mostraram que o evidenciador de placa Plax Magic promoveu alteração de cor em todos os materiais usados e em todos os tempos de leitura. A alteração de cor foi maior na resina Charisma, seguida da Z250 e EvoluX. Portanto, o evidenciador de placa promove alteração de cor em todos os materiais testados. A resina composta Charisma demonstrou menor estabilidade de cor que as resinas Z250 e EvoluX, que, por sua vez, foi a mais estável. Palavras-chave: Resinas Compostas. Higiene Oral. Cor.

scholarly journals COLOR STABILITY OF A NANOFILLED RESIN: INFLUENCE OF POLISHING AND FINISHING AND FLUORIDE SOLUTIONS ACCORDING TO TIME

2014 ◽  
Vol 2 (2) ◽  
pp. 119 ◽  
Author(s):  
Ana Luísa Botta Martins Oliveira ◽  
Patrícia Aleixo dos Santos Domingos ◽  
Juliana Alvares Duarte Bonini Campos ◽  
Ana Carolina Botta ◽  
Patrícia Petromilli Nordi Sasso Garcia
Keyword(s):  
Composite Resin ◽  
Color Change ◽  
Artificial Saliva ◽  
Color Stability ◽  
Repeated Measure ◽  
Color Analysis ◽  
Immersion Medium ◽  
Mixed Analysis ◽  
Initial Color ◽  
Level Of Significance

AIM: The aim of the study was evaluate the finishing and polishing effect of the color stability of the composite resin Filtek Supreme XT, according to different fluoride solutions and time. MATERIAL AND METHODS: Specimens were prepared (n=140) with half of the samples finished and polished. The experimental groups were divided according to the presence or absence of finishing and polishing and immersion solutions (artificial saliva, sodium fluoride solution at 0.05% - manipulated, Fluordent Reach, Oral B, Fluorgard). The specimens remained in artificial saliva for 24 hours and were subjected to an initial color analysis using a spectrophotometer CIELab system. Then, they were immersed in the experimental solutions for 1 minute a day. The readings of the color change were made after 24 and 48 hours, 7, 14, 21, 30 and 60 days after the first immersion. The three-way mixed Analysis of Variance (ANOVA) ("finishing/polishing", "immersion medium" and “time”) were performed. For multiple comparisons, the Sidak test for repeated measure was used, with a 5% level of significance. RESULTS: The finishing and polishing factor showed significant variability, independently of the immersion media (p<0.001). CONCLUSION: Finishing and polishing procedures yielded better color stability to composite resin over time, regardless of the immersion media.

scholarly journals Evaluation of surface roughness and color change of bovine enamel after immersion in dye solution

2018 ◽  
Vol 5 (5) ◽  
pp. 95
Author(s):  
Ana Carolina Trentino ◽  
Larissa Marinho Azevedo ◽  
Felipe Fabrício Farias Da Silva ◽  
Maria Cristina Carvalho de Almedra Freitas ◽  
Marina Studart Alencar Borges ◽  
...  
Keyword(s):  
Hydrogen Peroxide ◽  
Surface Roughness ◽  
Color Change ◽  
Artificial Saliva ◽  
In Vitro Study ◽  
Black Tea ◽  
Control Group ◽  
Change Analysis ◽  
Miller Test

Aim: The aim of this in vitro study was to evaluate the influence of dye solution on enamel color change after bleaching protocols and the effectiveness in maintaining the color of these agents.Material and Methods: The buccal surfaces of sixty-five bovine incisors were cleaned and polished, and the enamel specimens were divided into thirteen groups: G1 to G6: treated with 6% hydrogen peroxide using different surface agents; G7 to G12: treated with 15% hydrogen peroxide using different surface agents; G13: control. After 24 hours, the groups treated were immersed in black tea solution; the control group was stored in artificial saliva. The color was evaluated prior to bleaching, 24 hours later and after immersion in the dye solution; the roughness was measured immediately after bleaching, 24 hours later and 7 days after immersion in the dye solution. The data was analyzed using the Kruskal-Wallis test, followed by the Miller test for roughness analysis, and the Duncan test for color change analysis. It was used 5% significant level with p<0.05.Results: The data found in the evaluation of surface roughness after bleaching indicated a reduction of roughness in all the groups. The surface agent Bifluoride, when applied, showed an increase in roughness after its application and it decreases after immersion in dye solution; the surface agent Desensibilize and the XP Bond adhesive showed greater color alteration after immersion in dye solution.Conclusions: All the groups studied, under different whitening technique, were effective in promoting whitening.

scholarly journals Color Stability of Tetric® N-Ceram Bulk Fill Restorative Composite Resin after Immersion in Different Drinks

2017 ◽  
Vol 8 (1-2) ◽  
pp. 34-41
Author(s):  
Abdullah Saad Al-Abdullah ◽  
Roula S. Al-Bounni ◽  
Mohammad Al-Omari
Keyword(s):  
Composite Resin ◽  
Color Change ◽  
Color Stability ◽  
Energy Drink ◽  
Deionized Water ◽  
Control Group ◽  
Protein Supplement ◽  
Restorative Material ◽  
Significant Difference ◽  
Red Bull

Objective: To evaluate the color stability of Tetric® N-Ceram Bulk Fill composite restorative material after immersion in three different (energy drink, protein supplement solution, and combination of energy drink and protein supplement solution) drinks. Materials and Methods: Composite resin disks, 2 mm in depth and 5 mm in diameter, were prepared from the Tetric® N-Ceram Bulk Fill composite restorative material. Specimens were tested after immersion and aging in energy drink (Red Bull) alone, protein supplement solution alone, and in combination with energy drink and protein supplement. Deionized water was used as a control group. Specimens were stored at room temperature of ±23°C for a period of one week in each drink. Color was assessed in the CIELAB using Color Eye 7000A Spectrophotometer. Color differences in different group specimens were measured. Mean values were statistically analyzed using one-way analysis of variance (ANOVA). Further Tukey’s multiple comparison tests were applied to know the differences between the group of specimens. A p value of p < 0.05 was set as significance level. Results: N-Ceram Bulk Fill composite showed Δ L, Δ a, Δ b, and Δ E mean and standard deviation values when immersed in deionized water (–2.6 ± 3.24, 0.16 ± 0.19, 0.32 ± 1.26, and 3.51 ± 2.47), energy drink (–4.19 ± 4.24, 0.21 ± 0.21, 1.57 ± 1.32, and 5.40 ± 3.11), protein supplement (62.71 ± 12.48, –2.63 ± 0.7, 7.7 ± 5.67, and 63.45 ± 12.56), combined energy drink and protein supplement (68.52 ± 13.43, –4.06 ± 1.73, 10.94 ± 5.31, and 69.71 ± 13.42), respectively. All the color coordinates (Δ L, Δ a, and Δ b) showed statistically significant difference, p < 0.001. The color change of N-Ceram Bulk Fill composite specimens Δ E occurred by immersion in energy drink, protein supplement solution, and combined solution of energy drink and protein supplement after seven days was found to be statistically significant p < 0.001. Conclusion: The study’s finding suggests that the energy drink (Red Bull), protein supplement (ISOPURE), and combined immersion in energy drink and protein supplements caused perceptible and clinically unacceptable color change in the Tetric® N-Ceram Bulk Fill composite material. This color change was remarkably high with a combined immersion in energy drink and protein supplement solution.

scholarly journals Effects of Bleaching Agents on the Microhardness and Surface Roughness of Bulk Fill Composites

2017 ◽  
Vol 8 (3) ◽  
pp. 196-201 ◽  
Author(s):  
K Pradeep
Keyword(s):  
Surface Roughness ◽  
Physical Properties ◽  
Composite Resin ◽  
Artificial Saliva ◽  
Composite Resins ◽  
Control Group ◽  
Hardness Tester ◽  
Crucial Effect ◽  
Restorative Materials ◽  
The Mean

ABSTRACT Aim The aim was to compare the effect of 10 and 20% carbamide peroxide (CP) on microhardness (MHN) and surface roughness of two commercially available bulk fill composites (X-tra fill Bulk Fill and Tetric EvoCeram Bulk Fill). Materials and methods A total of 50 specimens with both type composites were prepared using brass molds of inner diameter 10 mm and a height of 4 mm. Each type of composite was further divided into three groups, control group stored in artificial saliva for 14 days, other groups bleached with 10 and 20% CP respectively, for 14 days. Microhardness of the composite resin was tested with a Vickers hardness tester, whereas surface roughness was tested with profilometer. Results All the analysis was performed using Statistical Package for the Social Sciences version 18. The value of p < 0.05 was considered statistically significant. Both 10 and 20% CP significantly reduced MHN of experimental composite resins. However, the mean surface roughness was significantly higher in X-tra fill Bulk Fill than Tetric EvoCeram Bulk Fill at 20% CP concentration. The mean MHN of Tetric EvoCeram was reduced when compared with X-tra fill at 20% CP. Conclusion There was a significant reduction in the MHN of restorative materials observed after exposure to CP under a clinically simulated bleaching regimen. However, increase in surface roughness was seen only at 20% CP. Clinical significance The physical properties, such as MHN and surface roughness have a crucial effect on the longevity of restorations and, moreover, on the esthetic demands of patients, but they may be compromised by bleaching treatments. The aim of this research paper was to assess the reaction of home bleaching agents on the physical properties of two Bulk Fill composite resin restorative materials. How to cite this article Francis G, Pradeep K, Ginjupalli K, Saraswathi V. Effects of Bleaching Agents on the Microhardness and Surface Roughness of Bulk Fill Composites. World J Dent 2017;8(3):196-201.

scholarly journals EFFECT OF SALBUTAMOL SULFAT EXPOSURE TO THE SURFACE ROUGHNESS OF BIOACTIVE RESIN

2021 ◽  
Vol 6 (1) ◽  
pp. 44
Author(s):  
Dewi Puspitasari ◽  
Diana Wibowo
Keyword(s):  
Surface Roughness ◽  
Composite Resin ◽  
Artificial Saliva ◽  
Control Design ◽  
Composite Resins ◽  
Control Group ◽  
Exposure Group ◽  
Salbutamol Sulfate ◽  
Treatment Groups ◽  
Post Test

ABSTRACTBioactive composite resin is the newest restorative resin material which has good mechanical and aesthetic properties. In the oral cavity, the restoration is degraded due to exposure to acids, one of which is exposure to asthma drugs. Properties of composite resins that can be affected by degradation include surface roughness. This study aims to analyze salbutamol sulfate exposure to the surface roughness of bioactive resins. The research method used was pure experimental design with post test-only with control design. The study used 39 specimens of bioactive resin (8 mm in diameter and 2 mm in thickness), divided into 3 treatment groups, namely the 400µg salbutamol sulfate exposure group, the 800µg salbutamol sulfate exposure group and the artificial saliva control group with treatment every 24 hours for 7 days, subsequently the specimens are tested with the surface roughness of the composite resin using a surface roughness tester. The highest surface roughness value was found in the 800µg group (8.23 ± 0.98 µm), followed by 400 µg group (5.43 ± 1.16 µm) and the lowest in the artificial saliva group (2.63 ± 0.82 µm). There were significant differences in all treatment groups. The exposure of salbutamol sulfate affects the surface roughness of the bioactive composite resin, a higher number of exposure doses indicates a higher surface roughness value.Keywords: bioactive composite resins, salbutamol sulfate, surface roughness

scholarly journals Evaluation of surface roughness and color change of a light-cured and a heat-cured acrylic resin employed for fabrication of prosthetic bases after exposure to different types of disinfectants

2013 ◽  
Vol 1 (3) ◽  
pp. 199
Author(s):  
Adriana Maria Jorge Dal'acqua Silva ◽  
Joice González Guerrero ◽  
Luciana De Rezende Pinto ◽  
Ricardo Martins Carvalho ◽  
Vinicius Carvalho Porto
Keyword(s):  
Surface Roughness ◽  
Sodium Hypochlorite ◽  
Composite Resin ◽  
Color Change ◽  
Acrylic Resin ◽  
Deionized Water ◽  
The Other ◽  
Distilled Water ◽  
Tukey Test ◽  
Different Types

This study evaluated the changes in surface roughness and color of materials employed in the fabrication of prosthetic bases after immersion in disinfectants. Sixty specimens were fabricated using a round matrix; half of the specimens were fabricated with a heat-cured composite resin, and the other half with a light-cured composite resin. After polishing, the specimens were stored in distilled water at 37ºC from 48 to 52 hours, and then submitted to initial tests of surface roughness and color. The specimens were randomly divided into three groups and immersed in the following chemicals: G1 (1% sodium hypochlorite for 10 minutes), G2 (5.25% sodium hypochlorite for 5 minutes) and G3 (2% acidic glutaraldehyde for 10 minutes). The surface roughness and color tests were once again performed and the specimens were then stored in deionized water at 37ºC for 6 days. On the seventh day, the immersion was repeated; this procedure was performed at every 7 days during 1 month and the tests were repeated after the fourth week. The results were submitted to three-way analysis of variance (ANOVA) and to the Tukey test. Within the same groups of specimens, statistically significant differences were only observed for the light-cured resin, which presented slight changes after exposure to 5.25% sodium hypochlorite and 2% glutaraldehyde for the interval ΔE2, which indicates differences in reading values between immersion after 30-day storage and the first immersion in the disinfectants.

Sign in / Sign up

Export Citation Format

Share Document