scholarly journals Experimental Study on Flow Characters of Salt Hydrate Slurry in Phase Change Temperature Range

2017 ◽  
Vol 21 (5) ◽  
pp. 15-23
Author(s):  
Muhammad Irsyad ◽  
Yuli S. Indartono ◽  
Ari D. Pasek ◽  
Willy Adriansyah
Keyword(s):  
Experimental Study ◽  
Phase Change ◽  
Salt Hydrate ◽  
Phase Change Temperature ◽  
Temperature Range ◽  
Change Temperature

The Influence of the Phase Change Temperature Range and the Phase Change Hysteresis of a PCM on the Performance of an Air-PCM Heat Storage Unit

2019 ◽  
Author(s):  
Pavel Charvat ◽  
Martin Zalesak ◽  
Lubomir Klimes
Keyword(s):  
Phase Change ◽  
Heat Storage ◽  
Simulation Studies ◽  
Storage Unit ◽  
Maximum Phase ◽  
Phase Change Temperature ◽  
Temperature Range ◽  
Air Temperatures ◽  
Change Temperature ◽  
Melting And Solidification

Abstract The influence of the phase change temperature range and the hysteresis of the enthalpy-temperature relationship h(T) of PCMs on the performance of thermal energy storage (TES) systems is rarely quantified. In the present study, the quantification is done by the comparison of the amounts of heat stored in (and discharged from) the air-PCM heat exchanger (TES unit) operating between constant air temperatures. All simulations were conducted for the same mean phase change temperature of the PCM (30 °C). The inlet air temperature of the air-PCM HEX was 40 °C during the heat charging period and 20 °C during the heat discharge period. The maximum considered phase change temperature range of the PCM was 10 °C. The maximum phase transition hysteresis, in the study defined as the temperature difference between the melting and solidification peaks, was 4 °C. The results indicate that in case of the PCMs with a wide phase change temperature range and a significant hysteresis of the h(T) curves, the influence of these properties cannot be neglected in the simulation studies in order to achieve accurate results.

scholarly journals Disturbing stability of interface by adopting phase-change temperature gradient to reduce ice adhesion strength

2019 ◽  
Vol 158 ◽  
pp. 69-75 ◽  
Author(s):  
Tingkun Chen ◽  
Jingfu Jin ◽  
Yingchun Qi ◽  
Weijun Tian ◽  
Qian Cong ◽  
...  
Keyword(s):  
Temperature Gradient ◽  
Phase Change ◽  
Adhesion Strength ◽  
Phase Change Temperature ◽  
Change Temperature ◽  
Ice Adhesion

A Study on the Cooling Characteristics of TMA Clathrate Compound with Additives

2006 ◽  
Vol 326-328 ◽  
pp. 1275-1278 ◽  
Author(s):  
Chang Oh Kim ◽  
Jin Heung Kim ◽  
Nak Kyu Chung
Keyword(s):  
Heat Source ◽  
Phase Change ◽  
Specific Heat ◽  
Freezing Point ◽  
Phase Change Temperature ◽  
Source Temperature ◽  
Heat Source Temperature ◽  
Clathrate Compound ◽  
Supercooling Degree ◽  
Change Temperature

This study aims to find out cooling characteristics of TMA 25wt%-water clathrate compound with ethanol such as supercooling, phase change temperature and specific heat. For this purpose, ethanol is added as per weight concentration and cooling experiment is performed at -6, -7 and -8, cooling heat source temperature, and it leads the following result. (1) Phase change temperature is decreased due to freezing point depression phenomenon. Especially, it is minimized as 5.1 and 5.0, 3.8 according to cooling source temperature in case that 0.5wt% of ethanol is added. (2) If 0.5wt% of ethanol is added, average supercooling degree is 0.9 and minimum supercooling is 0.8, 0.7 according to cooling heat source temperature. The restraint effect of supercooling is shown. (3) Specific heat shows tendency to decrease if ethanol is added. It is 3.013~3.048 kJ/kgK according to cooling heat source temperature if 0.5wt% of ethanol is added. Phase change temperature higher than that of water and inhibitory effect against supercooling can be confirmed through experimental study on cooling characteristics of TMA 25wt%-water clathrate compound by adding additive, ethanol.

scholarly journals Effect of Ion Irradiation on Amorphous and Crystalline Ge–Se and Their Application as Phase Change Temperature Sensor

2020 ◽  
pp. 2000429
Author(s):  
Al-Amin Ahmed Simon ◽  
Lyle Jones ◽  
Yoshifumi Sakaguchi ◽  
Henri Kunold ◽  
Isabella van Rooyen ◽  
...  
Keyword(s):  
Phase Change ◽  
Temperature Sensor ◽  
Ion Irradiation ◽  
Phase Change Temperature ◽  
Change Temperature

Preparation and Thermal Propertites of Polyethylene Glycol/ Silica Hollow Nanospheres Composite as Shape-Stabilized Phase Change Materials

2013 ◽  
Vol 773 ◽  
pp. 534-537 ◽  
Author(s):  
Li Li Feng ◽  
Jing Jing Tong ◽  
Chong Yun Wang
Keyword(s):  
Thermal Properties ◽  
Polyethylene Glycol ◽  
Phase Change ◽  
Porous Structure ◽  
Phase Change Materials ◽  
Hollow Nanospheres ◽  
Lower Phase ◽  
Phase Change Temperature ◽  
Change Temperature ◽  
Change Material

Shape-stabilized phase change material (PCM) composed of polyethylene glycol and silica hollow nanospheres was prepared by a vacuum impregnating method. Thermal properties of the composite PCM were investigated by various techniques. Lower phase change temperature and enthalpy of the composite PCM were observed. It is concluded that the phase change properties of the composite PCM are influenced by the adsorption confinement of the PEG segments from the porous structure of the silica hollow nanospheres.

Sign in / Sign up

Export Citation Format

Share Document