Enhanced Specific Heat Capacity of Molten Salt-Metal Oxide Nanofluid as Heat Transfer Fluid for Solar Thermal Applications

2010 ◽  
Author(s):  
Donghyun Shin ◽  
Debjyoti Banerjee
Keyword(s):  
Heat Transfer ◽  
Heat Capacity ◽  
Metal Oxide ◽  
Specific Heat ◽  
Molten Salt ◽  
Specific Heat Capacity ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Solar Thermal Applications

Thermal Analysis of Phase Change Material Based Heat Transfer Fluid in Solar Thermal Collector

2020 ◽  
Author(s):  
Tyler J. E. O’Neil ◽  
Celine S. L. Lim ◽  
Sarvenaz Sobhansarbandi
Keyword(s):  
Heat Capacity ◽  
Phase Change ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Phase Change Materials ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Liquid Form ◽  
High Specific Heat ◽  
Multi Walled Carbon Nanotubes

Abstract Phase change materials (PCMs) are commonly used as energy storage mediums in solar thermal systems. This paper investigates the mixture of PCM doped with nanoparticles to be used as HTFs directly integrated in a U-pipe ETC to be applied in solar thermal collectors. The selected type of PCM-HTF in this study is erythritol (C4H10O4), with high specific heat capacity in liquid form, as well as its unique sub-cooling behavior. In order to overcome the low thermal conductivity of erythritol and further enhance specific heat capacity, a weight concentration of 1% multi-walled carbon nanotubes (MWCNT) is added. Additionally, to insure even distribution of MWCNT and consistent properties of the HTF, triethanolamine (TEA) is proposed to be incorporated as a dispersant. The samples were each tested in a Thermogravimetric Analyzer (TGA) and Differential Scanning Calorimeter (DSC) to analyze their thermal properties. The results from the DSC tests show 12.4% enhancement of specific heat capacity of the proposed HTF mixture as well as nearly 5° C depression of freezing onset temperature. This study allows for the optimization of the operating temperature range of the collector when integrated with these materials, where direct heat gain can be obtained in the collector.

scholarly journals The Effect of In Situ Synthesis of MgO Nanoparticles on the Thermal Properties of Ternary Nitrate

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5737
Author(s):  
Zhiyu Tong ◽  
Linfeng Li ◽  
Yuanyuan Li ◽  
Qingmeng Wang ◽  
Xiaomin Cheng
Keyword(s):  
Heat Transfer ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Specific Heat ◽  
Molten Salt ◽  
Specific Heat Capacity ◽  
Ternary Eutectic ◽  
Mgo Nanoparticles ◽  
Nitrate System

The multiple eutectic nitrates with a low melting point are widely used in the field of solar thermal utilization due to their good thermophysical properties. The addition of nanoparticles can improve the heat transfer and heat storage performance of nitrate. This article explored the effect of MgO nanoparticles on the thermal properties of ternary eutectic nitrates. As a result of the decomposition reaction of the Mg(OH)2 precursor at high temperature, MgO nanoparticles were synthesized in situ in the LiNO3–NaNO3–KNO3 ternary eutectic nitrate system. XRD and Raman results showed that MgO nanoparticles were successfully synthesized in situ in the ternary nitrate system. SEM and EDS results showed no obvious agglomeration. The specific heat capacity of the modified salt is significantly increased. When the content of MgO nanoparticles is 2 wt %, the specific heat of the modified salt in the solid phase and the specific heat in the liquid phase increased by 51.54% and 44.50%, respectively. The heat transfer performance of the modified salt is also significantly improved. When the content of MgO nanoparticles is 5 wt %, the thermal diffusion coefficient of the modified salt is increased by 39.3%. This study also discussed the enhancement mechanism of the specific heat capacity of the molten salt by the nanoparticles mainly due to the higher specific surface energy of MgO and the semi-solid layer that formed between the MgO nanoparticles and the molten salt.

Experimental Investigation of Molten Salt Nanofluid for Solar Thermal Energy Application

2011 ◽  
Author(s):  
Donghyun Shin ◽  
Debjyoti Banerjee
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Molten Salt ◽  
Specific Heat Capacity ◽  
Thermal Energy ◽  
Molten Salts ◽  
Solar Power ◽  
Solar Thermal ◽  
Wide Range

The overall efficiency of a Concentrated Solar Power (CSP) system is critically dependent on the thermo-physical properties of the Thermal Energy Storage (TES) components and the Heat Transfer Fluid (HTF). Higher operating temperatures in CSP result in enhanced thermal efficiency of the thermodynamic cycles that are used in harnessing solar energy (e.g., using Rankine cycle or Stirling cycle). Particlularly, high specific heat capacity (Cp) and high thermal conductivity (k) of the HTF and TES materials enable reduction in the size and overall cost of solar power systems. However, only a limited number of materials are compatible for the high operating temperature requirements (exceeding 400°C) envisioned for the next generation of CSP systems. Molten salts have a wide range of melting point (200°C∼500°C) and are thermally stable up to 700°C. However, thermal property values of the molten salts are typically quite low (Cp is typically less than ∼2J/g-K and k is typically less than ∼1 W/m-K). To obviate these issues the molten salts can be doped with nanoparticles — resulting in the synthesis / formation of nanomaterials (nanocomposites and nanofluids). Nanofluids are colloidal suspensions formed by doping with minute concentration of nanoparticles. Nanofluids were reported for anomalous enhancement in their thermal conductivity values. In this study, molten salt-based nanofluids were synthesized by liquid solution method. A differential scanning calorimeter (DSC) was used to measure the specific heat capacity values of the proposed nanofluids. The observed enhancement in specific heat is then compared with predictions from conventional thermodynamic models (e.g. thermal equilibrium model or “simple mixing rule”). Transmission Electron Microscopy (TEM) is used to verify that minimal aggregation of nanoparticles occurred before and after the thermocycling experiments. Thermocycling experiments were conducted for repeated measurements of the specific heat capacity by using multiple freeze-thaw cycles of the nanofluids/ nano-composites, respectively. This study demonstrates the feasibility for using novel nanomaterials as high temperature nanofluids for applications in enhancing the operational efficiencies as well as reducing the cost of electricity produced in solar thermal systems utilizing CSP in combination with TES.

Experimental Study of Thermal Performance Enhancement of Molten Salt Nanomaterials

2018 ◽  
Author(s):  
Amirhossein Mostafavi ◽  
Vamsi Kiran Eruvaram ◽  
Donghyun Shin
Keyword(s):  
Heat Capacity ◽  
Specific Heat ◽  
Molten Salt ◽  
Specific Heat Capacity ◽  
Thermal Performance ◽  
Thermal Energy ◽  
Molten Salts ◽  
Elevated Temperatures ◽  
Performance Enhancement ◽  
Heat Transfer Fluid

Concentrating solar power (CSP) plants are one of the main technologies harvesting solar energy indirectly. In CSP systems, solar radiant light is concentrated into a focal receiver, where heat transfer fluid (HTF) as the energy carrier absorbs solar radiation. Thermal energy storage (TES) is the key method to expand operational time of CSP plants. Consequently, thermo-physical properties of the HTF is an important factor in transferring thermal energy. One of the promising chemicals for this purpose is a mixture of molten salts with stable properties at elevated temperatures. However, low thermal properties of molten salts, such as specific heat capacity (cp) around 1.5 kJ/kg°C, constrain thermal performance of CSP systems. Recently, many studies have been conducted to overcome this shortcoming, by adding minute concentration of nanoparticles. In this work, the selected molten salt eutectic is a mixture of LiNO3–NaNO3 by composition of 54:46 mol. % plus dispersing Silicon Dioxide (SiO2) nanoparticles with 10nm particle size. The results from the measured specific heat capacity by modulated differential scanning calorimeter (MDSC) shows a 9% cp enhancement. Moreover, the viscosity of the mixture is measured by a rheometer and the results show that the viscosity of molten salt samples increases by 27% and this may result in increasing the pumping energy of the HTF. Consequently, overall thermal performance of the selected mixture is investigated by figure of merit (FOM) analysis. The interesting results show an enhancement of the thermal storage of this mixture disregard with the viscosity increase effect.

Enhanced Sensible Heat Capacity of Molten Salt and Conventional Heat Transfer Fluid Based Nanofluid for Solar Thermal Energy Storage Application

2010 ◽  
Author(s):  
Hyun-eun Kwak ◽  
Donghyun Shin ◽  
Debjyoti Banerjee
Keyword(s):  
Heat Transfer ◽  
Heat Capacity ◽  
Physical Properties ◽  
Molten Salt ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Solar Thermal Energy ◽  
Silicon Dioxide Nanoparticles ◽  
Operational Capabilities ◽  
Thermo Physical Properties

In concentrating solar power (CSP) systems, the thermo-physical properties of the heat transfer fluid (HTF) are key parameters for enhancing the overall system efficiencies. Molten salts, such as alkali nitrates, chlorides or carbonates, and their eutectics, are considered as alternatives to conventional HTF (such as water or oil) to extend the operational capabilities of CSPS. However, the usage of the molten salt as the HTF is limited, since the heat capacity of the molten salt is relatively lower than that of conventional HTF. Nanofluid is a mixture of a fluid and nanoparticles. Well dispersed nanoparticles can be used to enhance the thermo-physical properties of HTF. In this study, silicon dioxide nanoparticles were dispersed into a molten salt and into a conventional HTF (Therminol VP-1, Solutia Inc). The specific heat enhancement of each nanofluid was studied and the applicability of such nanofluid materials for solar thermal storage applications was explored.

Central Receiver System Solar Power Plant Using Molten Salt as Heat Transfer Fluid

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
J. Ignacio Ortega ◽  
J. Ignacio Burgaleta ◽  
Félix M. Téllez
Keyword(s):  
Heat Transfer ◽  
Power Generation ◽  
Molten Salt ◽  
Thermal Power ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Solar Thermal Power ◽  
Central Receiver ◽  
Spanish Legislation ◽  
Solar Thermal Power Generation

Of all the technologies being developed for solar thermal power generation, central receiver systems (CRSs) are able to work at the highest temperatures and to achieve higher efficiencies in electricity production. The combination of this concept and the choice of molten salts as the heat transfer fluid, in both the receiver and heat storage, enables solar collection to be decoupled from electricity generation better than water∕steam systems, yielding high capacity factors with solar-only or low hybridization ratios. These advantages, along with the benefits of Spanish legislation on solar energy, moved SENER to promote the 17MWe Solar TRES plant. It will be the first commercial CRS plant with molten-salt storage and will help consolidate this technology for future higher-capacity plants. This paper describes the basic concept developed in this demonstration project, reviewing the experience accumulated in the previous Solar TWO project, and present design innovations, as a consequence of the development work performed by SENER and CIEMAT and of the technical conditions imposed by Spanish legislation on solar thermal power generation.

Thermal Analysis of Quaternary Molten Nitrate Salts Mixture for Energy Recovery System

2019 ◽  
Vol 796 ◽  
pp. 74-79
Author(s):  
Mohd Faizal Tukimon ◽  
Wan Nur Azrina Wan Muhammad ◽  
M. Nor Anuar Mohamad ◽  
Nurhayati Rosly ◽  
Norasikin Mat Isa
Keyword(s):  
Heat Capacity ◽  
Melting Point ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Energy Recovery ◽  
Heat Transfer Fluid ◽  
Energy Recovery System ◽  
Recovery System ◽  
Nitrate Salts ◽  
High Specific Heat

Quaternary molten salt nitrate have been used very practically as medium for energy storage or heat transfer fluid in terms of energy recovery system. Quaternary molten salt nitrate is a mixture that can transfer heat to generate energy such as electricity. Mixed alkaline molten nitrate salt can act as a heat transfer fluid due to their advantageous in terms of heat recovery system due to high specific heat capacity, low vapour pressure, low cost and wide range of temperature in its application. This studies shows about determining the new composition of quaternary molten nitrate salts from different primary salts that can possibly give a high specific heat capacity with low melting point. The mixture of quaternary molten nitrate salts was then heated inside the box furnace at 150°C for four hours and rose up the temperature to 400°C for eight hours. Through heating process, the quaternary molten nitrate alkaline was completely homogenized. The temperature was then dropped to room temperature before removing the mixture from the furnace. The specific heat capacities of each sample were determined by using Differential Scanning Calorimeter, DSC. From the result of DSC testing, Sample 6 gives the highest point of specific heat capacity and low melting point which is 0.4648 J/g°C and 97.71°C respectively. In the nut shell, Sample 6 was chosen as a good mixture with good thermal properties that has a low melting point which is below 100°C but high specific heat capacity that may be a helpful in the application energy recovery system.

scholarly journals Thermal Performance of Hybrid-Inspired Coolant for Radiator Application

Nanomaterials ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 1100
Author(s):  
F. Benedict ◽  
Amit Kumar ◽  
K. Kadirgama ◽  
Hussein A. Mohammed ◽  
D. Ramasamy ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Concentration ◽  
The Other ◽  
Hybrid Nanofluid ◽  
Hybrid Nanofluids ◽  
Tio2 Nanofluids

Due to the increasing demand in industrial application, nanofluids have attracted the considerable attention of researchers in recent decades. The addition of nanocellulose (CNC) with water (W) and ethylene glycol (EG) to a coolant for a radiator application exhibits beneficial properties to improve the efficiency of the radiator. The focus of the present work was to investigate the performance of mono or hybrid metal oxide such as Al2O3 and TiO2 with or without plant base-extracted CNC with varying concentrations as a better heat transfer nanofluid in comparison to distilled water as a radiator coolant. The CNC is dispersed in the base fluid of EG and W with a 60:40 ratio. The highest absorption peak was noticed at 0.9% volume concentration of TiO2, Al2O3, CNC, Al2O3/TiO2, and Al2O3/CNC nanofluids which indicates a better stability of the nanofluids’ suspension. Better thermal conductivity improvement was observed for the Al2O3 nanofluids in all mono nanofluids followed by the CNC and TiO2 nanofluids, respectively. The thermal conductivity of the Al2O3/CNC hybrid nanofluids with 0.9% volume concentration was found to be superior than that of the Al2O3/TiO2 hybrid nanofluids. Al2O3/CNC hybrid nanofluid dominates over other mono and hybrid nanofluids in terms of viscosity at all volume concentrations. CNC nanofluids (all volume concentrations) exhibited the highest specific heat capacity than other mono nanofluids. Additionally, in both hybrid nanofluids, Al2O3/CNC showed the lowest specific heat capacity. The optimized volume concentration from the statistical analytical tool was found to be 0.5%. The experimental results show that the heat transfer coefficient, convective heat transfer, Reynolds number and the Nusselt number have a proportional relationship with the volumetric flow rate. Hybrid nanofluids exhibit better thermal conductivity than mono nanofluids. For instance, a better thermal conductivity improvement was shown by the mono Al2O3 nanofluids than the CNC and TiO2 nanofluids. On the other hand, superior thermal conductivity was observed for the Al2O3/CNC hybrid nanofluids compared to the other mono and hybrid ones (Al2O3/TiO2).

Sign in / Sign up

Export Citation Format

Share Document