scholarly journals Temperature and Time Dependent Analysis of Tungsten Inert Gas Welding of Low Carbon Steel Plate using Goldak Model Heat Source

2019 ◽  
Vol 22 (11) ◽  
pp. 1719
Author(s):  
I Owunna ◽  
A.E Ikpe ◽  
J.I Achebo
Keyword(s):  
Carbon Steel ◽  
Heat Source ◽  
Steel Plate ◽  
Low Carbon Steel ◽  
Time Dependent ◽  
Inert Gas ◽  
Low Carbon ◽  
Tungsten Inert Gas Welding ◽  
Time Dependent Analysis

scholarly journals Evaluation of induced residual stresses on AISI 1020 low carbon steel plate from experimental and FEM approach during TIG welding process

2019 ◽  
Vol 13 (1) ◽  
pp. 4415-4433
Author(s):  
I. B. Owunna ◽  
A. E. Ikpe
Keyword(s):  
Carbon Steel ◽  
Residual Stresses ◽  
Steel Plate ◽  
Low Carbon Steel ◽  
Welding Process ◽  
Service Condition ◽  
Tig Welding ◽  
Von Mises Stress ◽  
Low Carbon ◽  
Temperature Range

Induced residual stresses on AISI 1020 low carbon steel plate during Tungsten Inert Gas (TIG) welding process was evaluated in this study using experimental and Finite Element Method (FEM). The temperature range measured from the welding experimentation was 251°C-423°C, while the temperature range measured from the FEM was 230°C-563°C; whereas, the residual stress range measured from the welding experimentation was 144MPa-402Mpa, while the residual range measured from the FEM was 233-477MPa respectively. Comparing the temperature and stress results obtained from both methods, it was observed that the range of temperature and residual stresses measured were not exactly the same due to the principles at which both methods operate but disparities between the methods were not outrageous. However, these values can be fed back to optimization tools to obtain optimal parameters for best practices.  Results of the induced stress distribution was created from a static study where the thermal results were used as loading conditions and it was observed that the temperature increased as the von-Mises stress increased, indicating that induced stresses in welded component may hamper the longevity of such component in service condition. Hence, post-weld heat treatment is imperative in order to stress relieve metals after welding operation and improve their service life.

Effect of Sol-Gel Film on the Corrosion Resistance of Low Carbon Steel Plate

2020 ◽  
Vol 984 ◽  
pp. 43-50
Author(s):  
Hua Yuan Zhang ◽  
Can Wang ◽  
Bing Xue ◽  
Jing Luo
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Steel Plate ◽  
Salt Spray ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Corrosion Current ◽  
Neutral Salt ◽  
Low Carbon ◽  
Gel Film

To improve the corrosion resistance on Q235 low carbon steel, in this paper, tetraethyl orthosilicate (TEOS), N-dodecyl trimethoxysilane and γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560) were used to make organic-inorganic hybrid sol-gel film. Cross cut test adhesion method, neutral salt spray test, electrochemical test and film protective efficiency were taken to value the corrosion resistance property. The corrosion topography was studied by optical microscope. In addition, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) curves and equivalent electric circuit fitting were used to analyze the corrosion mechanism. The cross cut adhesion of sol-gel film can reach 1 class and the protection class can attain 5 class after 72 hours neutral salt spray test. According to the potentiodynamic polarization curve analysis, the corrosion potential of sol-gel film coating sample after 0.5 hours immersion was -0.46 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.74×10-7 A·cm-2. The corrosion potential of bare Q235 low carbon steel plate after 0.5 hours immersion was -0.78 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.75×10-6 A·cm-2. The impedance value on 0.1 Hz (|Z|0.1Hz) (1.27×106 Ω·cm2) of sol-gel film coating sample was more than three orders of magnitude higher than the value of the low carbon steel plate. Even dipping in 3.5 wt. % NaCl for 72 hours, the |Z|0.1Hz value of sol-gel coating sample was still one order of magnitude higher than the low carbon steel plate with 0.5 hours immersion. Sol-gel film with excellent adhesion can significantly improve the corrosion resistance of low carbon steel plate. Sol-gel film can increase the protection efficiency of low carbon steel plate by 90%.

scholarly journals Characterization of Weld Bead Deposited on Low Carbon Steel Plate with TIG Welding Process

2020 ◽  
pp. 86-89
Keyword(s):  
Carbon Steel ◽  
Steel Plate ◽  
Low Carbon Steel ◽  
Welding Process ◽  
Weld Bead ◽  
Tig Welding ◽  
Low Carbon ◽  
Depth Of Penetration ◽  
Carbide Particles

The characterization of weld bead deposited on low carbon steel plate with TIG welding is carried out in the present study. Three beads on plate deposits were made on a low carbon steel plate by setting the current at 75, 100 and 125 Amp, voltage at 40 Volt and the weld speed at 0.5 mm/s. The wire is fed at the rate of 2.67 mm/s. A 1.8 mm filler wire made with low carbon steel was used. The macroscopic and microscopic examination of the sample was carried out. The depth of penetration was more with respect to rise in current value for the selected weld speed. At the heat affected zone (HAZ) fine grains were seen, closer to the HAZ recrystalised grains were noted. At the base metal large ferrite grains with fine carbide particles dispersed along the grain boundaries are observed.

TRIBOLOGICAL BEHAVIOR OF LOW-CARBON STEEL-PLATE-REINFORCED AL /SI ALLOY

2010 ◽  
Vol 33 (1) ◽  
pp. 47-51
Author(s):  
Abd Elmagid Nagi Attia ◽  
Hamdy Ahmed Nada ◽  
Asmaa Reiad Saad
Keyword(s):  
Carbon Steel ◽  
Steel Plate ◽  
Tribological Behavior ◽  
Low Carbon Steel ◽  
Low Carbon
Sign in / Sign up

Export Citation Format

Share Document