scholarly journals ANN and MLR Model of Specific Fuel Consumption for Pyrolysis Oil Blended with Diesel used in a Single Cylinder Diesel Engine: A Comparative Study

2015 ◽  
Vol 116 (10) ◽  
pp. 22-26
Author(s):  
Saumil CPatel ◽  
Pragnesh K Brahmbhatt
Keyword(s):  
Diesel Engine ◽  
Comparative Study ◽  
Fuel Consumption ◽  
Specific Fuel Consumption ◽  
Pyrolysis Oil ◽  
Single Cylinder ◽  
Mlr Model

scholarly journals Performance and Fuel Consumption of Diesel Engine Fueled by Diesel Fuel and Waste Plastic Oil Blends: An Experimental Investigation

2020 ◽  
Vol 4 (1) ◽  
pp. 20-26
Author(s):  
Sunaryo Sunaryo ◽  
Priyo Adi Sesotyo ◽  
Eqwar Saputra ◽  
Agus Pulung Sasmito
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Performance Test ◽  
Specific Fuel Consumption ◽  
Pyrolysis Oil ◽  
Promising Alternative ◽  
Waste Plastic ◽  
Waste Plastic Oil

This study analyzes the performance of the diesel engine in terms of power, torque, specific fuel consumption, and thermal efficiency using diesel and pyrolysis oil. The waste plastic oil (WPO) used in this research was produced through a pyrolysis process using raw materials from Low-density Polyethylene (LDPE) mixed with diesel fuel in volume ratios WPO10, WPO20, WPO30, WPO40, and WPO50. In addition, a performance test was carried out on the single-cylinder diesel engine test bench. The results showed that performing the diesel engine with the addition of WPO increased the average power and torque by 5% and 3%, thereby producing a higher heating value. Furthermore, the concentration of WPO also reduces the level of specific fuel consumption to be more efficient, with a decrease in thermal efficiency. In conclusion, plastic waste pyrolysis oil is a promising alternative fuel applicable to a diesel engine.

scholarly journals Performance of a drop-in biofuel emulsion on a single-cylinder research diesel engine

2016 ◽  
Vol 166 (3) ◽  
pp. 9-16
Author(s):  
Maria Bogarra-Macias ◽  
Omid Doustdar ◽  
Mohammed Fayad ◽  
Miroslaw Wyszyński ◽  
Athanasios Tsolakis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Research Work ◽  
Pyrolysis Product ◽  
High Energy ◽  
Waste To Energy ◽  
Gaseous Emissions ◽  
Pyrolysis Oil ◽  
Engine Operation ◽  
Single Cylinder

Current targets in reducing CO2 and other greenhouse gases as well as fossil fuel depletion have promoted the research for alternatives to petroleum-based fuels. Pyrolysis oil (PO) from biomass and waste oil is seen as a method to reduce life-cycle CO2, broaden the energy mix and increase the use of renewable fuels. The abundancy and low prices of feedstock have attracted the attention of biomass pyrolysis in order to obtain energy-dense products. Research has been carried out in optimising the pyrolysis process, finding efficient ways to convert the waste to energy. However, the pyrolysis products have a high content in water, high viscosity and high corrosiveness which makes them unsuitable for engine combustion. Upgrading processes such as gasification, trans-esterification or hydro-deoxynegation are then needed. These processes are normally costly and require high energy input. Thus, emulsification in fossil fuels or alcohols is being used as an alternative. In this research work, the feasibility of using PO-diesel emulsion in a single-cylinder diesel engine has been investigated. In-cylinder pressure, regulated gaseous emissions, particulate matter, fuel consumption and lubricity analysis reported. The tests were carried out of a stable non-corrosive wood pyrolysis product produced by Future Blends Ltd of Milton Park, Oxfordshire, UK. The product is trademarked by FBL, and is a stabilized fraction of raw pyrolysis oil produced in a process for which the patent is pending. The results show an increase in gaseous emissions, fuel consumption and a reduction in soot. The combustion was delayed with the emulsified fuel and a high variability was observed during engine operation.

Effects of Injection Pressure on Output Power, BTE, SFC and Opacity in a Typical Single-Cylinder Diesel Engine

2020 ◽  
Vol 3 (1) ◽  
pp. 20-26
Author(s):  
Farid Majedi ◽  
Denik Setiyaningrum ◽  
Setyono M. T. Hidayahtullah ◽  
Aries Abbas
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Output Power ◽  
Thermal Efficiency ◽  
Engine Speed ◽  
Injection Pressure ◽  
Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Single Cylinder ◽  
Load Variations

On a single-cylinder diesel engine, injection pressure can be adjusted by changing the thickness of the injector shim. In this study, the injection pressure of 180 bar (standard), 190 bar (+1mm shim), and 210 bar (+2mm shim) was examined on a typical single-cylinder diesel engine with pure diesel fuel. The tests carried out at a constant engine speed of 1500 rpm with load variations of 650, 1300, 1950, and 3600 Watts to investigate the effect of injection pressure on output power, brake thermal efficiency (BTE), specific fuel consumption (SFC) and opacity. The results showed that increasing injection pressure could increase the output power by 19.3% and 17.4% by adding 1 mm and 2 mm shims, respectively. SFC decreased 1.97% and 12.3% compared to standard conditions and opacity with 2 mm shim was lower than 1 mm shim. In conclusion, increasing the injection pressure from 180 to 210 bar by adding 2 mm shim can improve the performance of a single cylinder diesel engine, which includes output power, brake thermal efficiency (BTE), specific fuel consumption (SFC) and opacity.

scholarly journals Effect of algae fuel addition on fuel consumption and thermal efficiency of single cylinder diesel engine

2021 ◽  
Vol 1068 (1) ◽  
pp. 012016
Author(s):  
Hazim Sharudin ◽  
N.A. Rahim ◽  
N.I. Ismail ◽  
Sharzali Che Mat ◽  
Nik Rosli Abdullah ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Single Cylinder

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

scholarly journals Performance Evaluation of Single Cylinder Diesel Engine Using Tyre Pyrolysis Oil (TPO) Blends

2019 ◽  
Vol 7 (2) ◽  
pp. 46-51
Author(s):  
P M Bhatt
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Petroleum Products ◽  
Permissible Limit ◽  
Pyrolysis Oil ◽  
Single Cylinder ◽  
Performance And Emission ◽  
Partial Load ◽  
Alternate Fuels

Increasing industrialization and motorization led to a significant rise in demand of petroleum products. As these are the non-renewable resources, it will be troublesome to predict the availability of these resources in the future, resulting in uncertainty in its supply and price and is impacting growing economies like India importing 80% of the total demand of the petroleum products. Many attempts have been made by different researchers to find out alternate fuels for Internal Combustion engines. Many alternate fuels like Biodiesel, LPG (Liquefied Petroleum Gas), CNG (Compressed Natural Gas) and Alcohol are being used nowadays by different vehicles. In this context pyrolysis of scrap tyres can be used effectively to produce oil, thereby solving the problem of waste tyre disposal. In the present study, Experimental investigations were carried out to evaluate the performance and emission characteristics of a single cylinder diesel engine fueled by TPO10, TPO15, and TPO20 at a crank angle 280 before TDC (Top Dead Centre) and injection pressure of 180 bar keeping the blend quality by controlling the density and viscosity of tyre pyrolysis oil within permissible limit of euro IV diesel requirement. The performance and emission results were analyzed and compared with that of diesel fuel operation. The results of investigations indicate that the brake thermal efficiency of the TPO - DF blend decreases by 4 to 8%. CO emissions are slightly higher but within permissible limit of euro IV emission standards. HC emissions are higher by about 40 to 60% at partial load whereas smoke opacity is lower by about 14% to 22% as compared to diesel fuel.

Sign in / Sign up

Export Citation Format

Share Document