scholarly journals Conversor Doubler Output Coupled Inductor para Aplicações de Fontes Alternativas

2021 ◽  
Author(s):  
HENRIQUE JAHNKE HOCH ◽  
TIAGO MIGUEL KLEIN FAISTEL ◽  
ADEMIR TOEBE ◽  
ANTóNIO MANUEL SANTOS SPENCER ANDRADE
Keyword(s):  
High Voltage ◽  
Duty Cycle ◽  
Low Voltage ◽  
Energy Generation ◽  
Boost Converter ◽  
Voltage Gain ◽  
Switched Capacitors ◽  
Number Of Components ◽  
Photovoltaic Energy ◽  
High Voltage Gain

High step-up DC-DC converters are necessary in photovoltaic energy generation, due the low voltage of the panels source. This article propose the Doubler Output Coupled Inductor converter. This converter is based in boost converter and utilize switched capacitors and a coupled inductor to maximize the static voltage gain. The converter achieve a high voltage gain with low turns ratio in the coupled inductor and an acceptable duty cycle. Can highlight the converter utilize low number of components and have low voltage and current stresses in semiconductors. To validate and evaluate the operation of the converter a 200W prototype is simulated.

scholarly journals A Family of Bidirectional DC–DC Converters for Battery Storage System with High Voltage Gain

Energies ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1289 ◽  
Author(s):  
Hailong Zhang ◽  
Yafei Chen ◽  
Sung-Jun Park ◽  
Dong-Hee Kim
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Storage System ◽  
Critical Factor ◽  
Operating Mode ◽  
Boost Converter ◽  
Voltage Gain ◽  
Experimental Conditions ◽  
Number Of Components ◽  
High Voltage Gain

In low power energy storage systems, to match the voltage levels of the low-voltage battery side and high-voltage direct current (DC) bus, a high voltage gain converter with bidirectional operation is required. In this system, the cost effectiveness of the design is a critical factor; therefore, the system should be designed using a small number of components. This paper proposes a set of bidirectional converters with high voltage gain range based on the integration of the boost converter with a Ćuk converter, single ended primary inductor converter (Sepic), and buck-boost converter. The proposed converters consist of a small number of components with a high voltage gain ratio. Detailed comparisons are made with respect to the operating mode, number of components, voltage, and current ripple and efficiency. The efficiency of proposed converters are higher than the conventional converters in entire power range, and 6% higher efficiency can be achieved in large duty cycle by calculating loss analysis. To verify performances of the proposed converters, three 200-W prototypes of the converters are developed under the same experimental conditions. The results revealed that converter I exhibits the highest efficiency in the boost mode (92%) and buck mode (92.2%). The experimental results are shown to verify the feasibility and performances of the set of converters.

An improved DC-DC converter with high voltage gain based on fully tapped quadratic boost converter for grid connected solar PV micro-inverter

2020 ◽  
pp. 014233122092198
Author(s):  
Lakhdar Bentouati ◽  
Ali Cheknane ◽  
Boumediène Benyoucef ◽  
Oscar Barambones
Keyword(s):  
High Voltage ◽  
Duty Cycle ◽  
Boost Converter ◽  
Maximum Efficiency ◽  
Duty Ratio ◽  
Voltage Gain ◽  
Solar Pv ◽  
Pv Systems ◽  
High Voltage Gain ◽  
Urgent Task

The need to increase the voltage level produced by PV systems becomes an urgent task to be compatible with the requirements of the AC load, but we meet problems in the operation of the step-up converter at a high duty cycle which is not preferred due to the reduction in voltage gain, and also a higher number of turns ratio in the windings inductance coupled adds to the overall losses of the converter. This article proposes an improved DC-DC converter with a lower duty cycle by integrating three tapped-inductors in new topology, which combined quadratic boost converter and tapped-inductor boost converter. The proposed converter achieves a high voltage gain with a lower duty ratio (Gmax = 14.32) and a maximum efficiency of 98.68% is improved compared to the voltage gain and efficiency results of these converters in several recently published references. The analyses are done theoretically and supported with simulation results. A prototype of the proposed converter has been built to experimentally validate the obtained results.

scholarly journals High gain multiphase boost converter based-on capacitor clamping structure

2021 ◽  
Vol 24 (2) ◽  
pp. 689
Author(s):  
Oday Saad Fares ◽  
Jasim Farhood Hussen
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Low Voltage ◽  
High Gain ◽  
Industrial Applications ◽  
Boost Converter ◽  
Power Device ◽  
Voltage Gain ◽  
High Voltage Gain ◽  
And Performance

<p>In the last few years, the non-isolated dc converters involving high voltage gain with adequate performance are becoming quite popular in industrial applications. This is resulting in high voltage and current stress on the power device (switches and diodes), as well as a limited output voltage with a high duty cycle. This paper proposes a multi-phase non-isolated boost converter that uses capacitor clamping to increase output voltage while reducing stress across the power device. There are two stages in the proposed converter (first stage is three inductors and three switches and the second stage is clamper circuit of three capacitors and three diodes). The proposed converter is high voltage gain, with low voltage stress through switches transistors. To justify the theoretical analysis, the concept was validated through mathematical analysis and by simulation using MATLAB/SIMULINK. The results carried out the results permit the converter behavior and performance to be accurately.</p>

scholarly journals A Transformer less Buck-Boost Converter with Single Switch

2020 ◽  
Vol 9 (12) ◽  
pp. 355-358
Keyword(s):  
High Voltage ◽  
Duty Cycle ◽  
Boost Converter ◽  
Voltage Gain ◽  
Improve Efficiency ◽  
Conduction Loss ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Active Switch

This paper introduces a modern, transformerless buck-boost dc-dc converter. In this topology, one active switch is used. The proposed buck-boost converter voltage gain is higher compared to the conventional buck-boost converter. With a moderate duty cycle, high voltage gain can be reached. The switch's voltage stress is minimal. As a consequence, the power switch's conduction loss is relatively low to improve efficiency. The converter is simple, hence it will be easy to control the proposed converter.

scholarly journals A Quadratic Boost Converter with Voltage Multiplier Cell to Increase Voltage Gain

2021 ◽  
Vol 7 (03) ◽  
pp. 76-79
Author(s):  
P.Rangeela and Dr.A.RubyMeena
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Loop Control ◽  
Voltage Multiplier ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Integral Controller ◽  
Proportional Integral Controller

The high step up dc-dc converter with a quadratic boost converter with voltage multiplier cell (VM) to achieve a high voltage gain in the continuous conduction mode (CCM). To increase higher voltage gain, lower voltage stress on diodes and capacitors and requiring smaller inductors with reduced number of components. Quadratic Boost DC-DC converters are mainly used in applications like HEVs and EVs vehicles. The purpose of boost converter is to charge a low-voltage (12 V) battery during boost mode and to assist the high-voltage 200V battery. In this implementation, closed-loop control in high voltage side is implemented using PI (proportional integral) controller.

scholarly journals A Quadratic Boost Converter with Voltage Multiplier Cell to Increase Voltage Gain

2021 ◽  
Vol 7 (03) ◽  
pp. 76-79
Author(s):  
P.Rangeela and Dr.A.RubyMeena
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Loop Control ◽  
Voltage Multiplier ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Integral Controller ◽  
Proportional Integral Controller

The high step up dc-dc converter with a quadratic boost converter with voltage multiplier cell (VM) to achieve a high voltage gain in the continuous conduction mode (CCM). To increase higher voltage gain, lower voltage stress on diodes and capacitors and requiring smaller inductors with reduced number of components. Quadratic Boost DC-DC converters are mainly used in applications like HEVs and EVs vehicles. The purpose of boost converter is to charge a low-voltage (12 V) battery during boost mode and to assist the high-voltage 200V battery. In this implementation, closed-loop control in high voltage side is implemented using PI (proportional integral) controller

A Nonisolated DC–DC Boost Converter With High Voltage Gain and Balanced Output Voltage

2014 ◽  
Vol 61 (12) ◽  
pp. 6739-6746 ◽  
Author(s):  
George Cajazeiras Silveira ◽  
Fernando Lessa Tofoli ◽  
Luiz Daniel Santos Bezerra ◽  
Rene Pastor Torrico-Bascope
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
High Voltage Gain

scholarly journals High Step-up Coupled Inductor Inverters Based on qSBIs

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 3032 ◽  
Author(s):  
Hongchen Liu ◽  
Xi Su ◽  
Junxiong Wang
Keyword(s):  
Steady State ◽  
High Voltage ◽  
Low Voltage ◽  
Duty Ratio ◽  
Voltage Gain ◽  
Passive Components ◽  
Steady State Analysis ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Working Principle

In this paper, two types of high step-up coupled inductor inverters based on qSBIs (quasi- switched boost inverters) are proposed. By applying the coupled inductor to the qSBIs, the voltage gain of the proposed inverter is regulated by turn ratio and duty ratio. Thus, a high voltage gain can be achieved without the circuits operating at the extreme duty cycle by choosing a suitable turn ratio of the coupled inductor. In addition, the proposed circuits have the characteristics of continuous input current and low voltage stress across the passive components. A boost unit can be added to the proposed inverters for further improvement of the voltage gain. In this paper, the working principle, steady state analysis, and the comparisons of the proposed inverter with other impedance-source inverters are described. A 200 W prototype was created and the experimental results confirm the correctness of the analysis in this paper.

Sign in / Sign up

Export Citation Format

Share Document