Development of various types of small-scale gas turbine engines based on a unified core engine

2019 ◽  
pp. 11-18
Author(s):  
I.V. Osipov ◽  
V.S. Lomazov
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Small Scale ◽  
Gas Turbine Engines

Thermo-Economic Optimization in the Design of Small-Scale and Residential Cogeneration Systems

2009 ◽  
Author(s):  
C. P. Lea˜o ◽  
S. F. C. F. Teixeira ◽  
A. M. Silva ◽  
M. L. Nunes ◽  
L. A. S. B. Martins
Keyword(s):  
Gas Turbine ◽  
Urban Areas ◽  
Pressure Ratio ◽  
Optimization Method ◽  
Turbine Engines ◽  
Small Scale ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Economic Optimization ◽  
Micro Turbine

In recent years, gas-turbine engines have undergone major improvements both in efficiency and cost reductions. Several inexpensive models are available in the range of 30 to 250 kWe, with electrical efficiencies already approaching 30%, due to the use of a basic air-compressor associated to an internal air pre-heater. Gas-turbine engines offer significant advantages over Diesel or IC engines, particularly when Natural Gas (NG) is used as fuel. With the current market trends toward Distributed Generation (DG) and the increased substitution of boilers by NG-fuelled cogeneration installations for CO2 emissions reduction, small-scale gas turbine units can be the ideal solution for energy systems located in urban areas. A numerical optimization method was applied to a small-scale unit delivering 100 kW of power and 0.86 kg/s of water, heated from 318 to 353K. In this academic study, the unit is based on a micro gas-turbine and includes an internal pre-heater, typical of these low pressure-ratio turbines, and an external heat recovery system. The problem was formulated as a non-linear optimisation model with the minimisation of costs subject to the physical and thermodynamic constraints. Despite difficulties in obtaining data for some of the components cost-equations, the preliminary results indicate that the optimal compressor pressure ratio is about half of the usual values found in large installations, but higher than those of the currently available micro-turbine models, while the turbine inlet temperature remains virtually unchanged.

scholarly journals Correlation-regression models for calculating the weight of small-scale aircraft gas turbine engines

2018 ◽  
Vol 220 ◽  
pp. 03004
Author(s):  
Evgeny Filinov ◽  
Daria Kolmakova ◽  
Sergey Avdeev ◽  
Sergey Krasilnikov
Keyword(s):  
Gas Turbine ◽  
Regression Models ◽  
Design Stage ◽  
Turbine Engines ◽  
Small Scale ◽  
Gas Turbine Engines ◽  
Turbofan Engines ◽  
New Correlation ◽  
Engine Design ◽  
Weight Calculation

Several new correlation-regression models of weight calculation for small-scale aircraft gas turbine engines are proposed for their conceptual design stage. A comparison of the obtained weight models with each other and with the Kuz’michev model is carried out. Based on the obtained results, conclusions about the feasibility and scope of their application are drawn. New correlation-regression models differ from each other in the number of input parameters, as well as in the accuracy of forecasting the weight. In the course of the work, a database of main data and thermodynamic parameters of turbofan engines (TFE) is created consisting of 92 small-scale TFEs with thrust less than 50 kN. Based on the collected statistics, formulas were obtained that allow calculating the weight at the initial stage of engine design. The error in calculating the weight by these models is in range from 10% to 30%.

scholarly journals Thermodynamic designing of the small-scale gas turbine engine family with common core

2018 ◽  
Vol 220 ◽  
pp. 03007
Author(s):  
Andrey Tkachenko ◽  
Evgeny Filinovaroslav Ostapyuk ◽  
Viktor Rybakov ◽  
Daria Kolmakova
Keyword(s):  
Gas Turbine ◽  
Common Core ◽  
Turbine Engines ◽  
Small Scale ◽  
Gas Turbine Engines ◽  
Working Process ◽  
Turbofan Engine ◽  
Engine Family ◽  
Power Turbine ◽  
The Cost

The paper describes the method of selecting the working process parameters of a family of small-scale gas turbine engines (GTE) with common core. As an example, the thermodynamic design of a family of small-scale gas turbine engines (SGTE) with common core was carried out. The engine family includes a small-scale turbojet engine (STJE) and a gas turbine plant (GTP), which electric generator is driven by power turbine. The selection of rational values for the working process parameters of STJE and GTP was carried out in CAE system ASTRA on the basis of nonlinear optimization of these parameters, taking into account functional and parametric constraints. The quantitative results of deterioration in the performance of the engines of the family with common core are obtained in comparison with the engines with the optimum core for each type. However, the advanced creation of a common core can reduce the cost and timing of the engine creation, ensure its higher reliability (due to the development of the base common core) and reduce the cost of its production. The method of selecting the parameters of the working process of the GTE family with common core presents the solution to more complex problems, such as the possibility of developing a family consisting of five engines: a turbojet engine, turbofan engine, turbofan engine with a complex cycle, GTE with power turbine (GTE-PT), GTE-PT with recovery.

Gas Screen in Components of Gas Turbine Engines

1997 ◽  
Vol 28 (7-8) ◽  
pp. 536-542
Author(s):  
A. A. Khalatov ◽  
I. S. Varganov
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Gas Screen

Potential Application of Composite Materials to Future Gas Turbine Engines

1988 ◽  
Author(s):  
James C. Birdsall ◽  
William J. Davies ◽  
Richard Dixon ◽  
Matthew J. Ivary ◽  
Gary A. Wigell
Keyword(s):  
Composite Materials ◽  
Gas Turbine ◽  
Potential Application ◽  
Turbine Engines ◽  
Gas Turbine Engines

Method of tribodiagnostics of d-30KU engines/KP with the use of a microwave plasma complex: results of metrological examination and analysis of the accuracy

2020 ◽  
pp. 22-29
Author(s):  
A. Bogoyavlenskiy ◽  
A. Bokov
Keyword(s):  
Gas Turbine ◽  
Microwave Plasma ◽  
Technical Condition ◽  
The State ◽  
Turbine Engines ◽  
Metrological Examination ◽  
Gas Turbine Engines ◽  
High Frequency Plasma ◽  
Frequency Plasma ◽  
Primary Standards

The article contains the results of the metrological examination and research of the accuracy indicators of a method for diagnosing aircraft gas turbine engines of the D30KU/KP family using an ultra-high-frequency plasma complex. The results of metrological examination of a complete set of regulatory documents related to the diagnostic methodology, and an analysis of the state of metrological support are provided as well. During the metrological examination, the traceability of a measuring instrument (diagnostics) – an ultrahigh-frequency plasma complex – is evaluated based on the scintillation analyzer SAM-DT-01–2. To achieve that, local verification schemes from the state primary standards of the corresponding types of measurements were built. The implementation of measures to eliminate inconsistencies identified during metrological examination allows to reduce to an acceptable level the metrological risks of adverse situations when carrying out aviation activities in industry and air transportation. In addition, the probability of occurrence of errors of the first and second kind in the technological processes of tribodiagnostics of aviation gas turbine engines is reduced when implementing a method that has passed metrological examination in real practice. At the same time, the error in determining ratings and wear indicators provides acceptable accuracy indicators and sufficient reliability in assessing the technical condition of friction units of the D-30KP/KP2/KU/KU-154 aircraft engines.

Sign in / Sign up

Export Citation Format

Share Document