scholarly journals STATE OF THE ART OF SURFACE TEXTURING FOR BIOTRIBOLOGY APPLICATIONS

2021 ◽  
Vol 13 (3) ◽  
pp. 143-150
Author(s):  
Daniel I. Quintanilla-Correa ◽  
◽  
Laura Peña-Parás ◽  
Demofilo Maldonado-Cortés ◽  
Martha Claudia Rodriguez-Villalobos ◽  
...  
Keyword(s):  
State Of The Art ◽  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Surface Pattern ◽  
Wear Particles ◽  
Abrasive Particles ◽  
Useful Life ◽  
Three Body

Surface texturing can be defined as a technique that consists of creating micro cavities in the surface of a material. There are different texturing techniques such as chemical etching, electromechanical micromachining, diamond embossing, electric discharge, pellet-pressing and laser surface, the last being the most common. For years, these surface texturing techniques have been used in tribological applications because microcavities can store oils or fluids and constantly lubricate the surfaces that are subjected to wear; they can also be used to trap wear particles (debris) that would otherwise act as abrasive particles (three body abrasive wear). This literature review seeks to analyse and compare the advantages that the use of surface texturing techniques can offer in reducing the wear of prosthetic components and therefore lengthening their useful life, to provide a better quality of life to patients. The results of this review showed a growing interest in the scientific community in the use of surface texturing for biotribogical applications, using to a greater extent the Laser Surface Texturing (LST) technique and the surface pattern composed by dimples.

State of the Art in Laser Surface Texturing

Volume 1 ◽  
2004 ◽  
Author(s):  
Izhak Etsion
Keyword(s):  
Surface Engineering ◽  
State Of The Art ◽  
Load Capacity ◽  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Mechanical Seals ◽  
Current Effort ◽  
Hydrodynamic Bearing ◽  
Micro Dimples

Surface texturing has emerged in the last decade as a viable option of surface engineering resulting in significant improvement in load capacity, wear resistance, friction coefficient etc. of tribological mechanical components. Various techniques can be employed for surface texturing but Laser Surface Texturing (LST) is probably the most advanced so far. LST produces a very large number of micro-dimples on the surface and each of these micro-dimples can serve either as a micro- hydrodynamic bearing in cases of full or mixed lubrication, a micro-reservoir for lubricant in cases of starved lubrication conditions, or a micro-trap for wear debris in either lubricated or dry sliding. The present paper reviews the current effort being made world wide on surface texturing in general and on laser surface texturing in particular. It presents the state of the art of LST and the potential of this technology in various lubricated applications like mechanical seals, piston rings and thrust bearings. The paper also describes some fundamental on going research around the world with LST.

Control of the quality of laser surface texturing

2008 ◽  
Vol 14 (9-11) ◽  
pp. 1553-1557 ◽  
Author(s):  
Christophe Vincent ◽  
Guy Monteil ◽  
Thierry Barriere ◽  
Jean Claude Gelin
Keyword(s):  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing

State of the Art in Laser Surface Texturing

2005 ◽  
Vol 127 (1) ◽  
pp. 248-253 ◽  
Author(s):  
Izhak Etsion
Keyword(s):  
Surface Engineering ◽  
State Of The Art ◽  
Load Capacity ◽  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Mechanical Seals ◽  
Current Effort ◽  
Hydrodynamic Bearing ◽  
Micro Dimples

Surface texturing has emerged in the last decade as a viable option of surface engineering resulting in significant improvement in load capacity, wear resistance, friction coefficient etc. of tribological mechanical components. Various techniques can be employed for surface texturing but Laser Surface Texturing (LST) is probably the most advanced so far. LST produces a very large number of micro-dimples on the surface and each of these micro-dimples can serve either as a micro-hydrodynamic bearing in cases of full or mixed lubrication, a micro-reservoir for lubricant in cases of starved lubrication conditions, or a micro-trap for wear debris in either lubricated or dry sliding. The present paper reviews the current effort being made world wide on surface texturing in general and on laser surface texturing in particular. It presents the state of the art in LST and the potential of this technology in various lubricated applications like mechanical seals, piston rings and thrust bearings. The paper also describes some fundamental on going research around the world with LST.

scholarly journals Does laser surface texturing really have a negative impact on the fatigue lifetime of mechanical components?

Friction ◽  
2021 ◽  
Author(s):  
Chia-Jui Hsu ◽  
Andreas Stratmann ◽  
Simon Medina ◽  
Georg Jacobs ◽  
Frank Mücklich ◽  
...  
Keyword(s):  
Boundary Lubrication ◽  
Surface Texturing ◽  
Contact Stresses ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Wear Loss ◽  
Textured Surface ◽  
Periodic Patterns ◽  
Rolling Bearings ◽  
Fatigue Lifetime

AbstractLaser surface texturing (LST) has been proven to improve the tribological performance of machine elements. The micro-scale patterns manufactured by LST may act as lubricant reservoirs, thus supplying oil when encountering insufficient lubrication. However, not many studies have investigated the use of LST in the boundary lubrication regime, likely due to concerns of higher contact stresses that can occur with the increasing surface roughness. This study aims to examine the influence of LST on the fatigue lifetime of thrust rolling bearings under boundary lubrication. A series of periodic patterns were produced on the thrust rolling bearings, using two geometrically different designs, namely cross and dimple patterns. Base oil ISO VG 100 mixed with 0.05 wt% P of zinc dialkyldithiophosphate (ZDDP) was supplied. The bearings with cross patterns reduce the wear loss by two orders of magnitude. The patterns not only retain lubricant in the textured pockets but also enhance the formation of an anti-wear tribofilm. The tribofilm generation may be improved by the higher contact stresses that occur when using the textured surface. Therefore, in contrast to the negative concerns, the ball bearings with cross patterns were instead found to increase the fatigue life by a factor of three.

Tribological effects of laser surface texturing and residual stress

2018 ◽  
Vol 70 (1) ◽  
pp. 126-132 ◽  
Author(s):  
Shuwen Wang ◽  
Feiyan Yan ◽  
Ao Chen
Keyword(s):  
Residual Stress ◽  
Wear Resistance ◽  
Friction And Wear ◽  
Surface Texturing ◽  
Laser Surface ◽  
Friction Reduction ◽  
Laser Surface Texturing ◽  
Wear Testing ◽  
Content Type ◽  
Surface Textures

Purpose The purpose of this paper is to investigate the tribological effects of laser surface texturing (LST) and residual stress on functional surfaces. Design/methodology/approach Three different surface textures (circular dimple, elliptical dimple and groove) with two different textured area ratios (10 and 20 per cent) are designed and fabricated by a Picosecond Nd YAG Laser machine. The friction and wear performance of textured specimens is tested using a UMT-2 friction and wear testing machine in mixed lubrication. Findings Test results show that elliptical dimples exhibit the best performance in wear resistance, circular dimples in friction reduction and grooves in stabilization of friction. The surfaces with larger textured area density exhibit better performance in both friction reduction and wear resistance. The improved performance of LST is the coupled effect of surface texture and residual stress. Originality/value The findings of this study may provide guidance for optimal design of functional surface textures in reciprocating sliding contacts under mixed or hydrodynamic lubrication, which can be used in automotive and other industrial applications.

Effect of Micro-Manufacturing Processes on Surface Behavior

2007 ◽  
Author(s):  
Tiffany Davis ◽  
Jian Cao ◽  
Wei Chen ◽  
Q. Jane Wang ◽  
Cedric Xia ◽  
...  
Keyword(s):  
Surface Texture ◽  
Surface Texturing ◽  
Steel Sample ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Copper Sheet ◽  
Property Variation ◽  
Nano Indentation ◽  
Interface Surface ◽  
Significant Difference

Surface texturing has become a valuable technique for reducing friction and wear in contacting parts; laser surface texturing is one such method used to create micro-dimples on the interface surface. This work investigates the surface material property variation caused by laser surface texturing. The hardness and modulus of elasticity of a steel laser surface texture sample were evaluated near the dimples and away from the dimpled zone through nano-indentation. Resulting data shows that no significant difference exists between the material properties from the two positions. An alternate technique for surface texture generation was also explored, involving the use of micro-punches to create surface features in a metal sample. Computational simulations were performed using a second material underneath a thin copper sheet. The second material was present to serve as a support and to allow extensive deformation of the top material. The choice of the support material and ratio of material thicknesses was optimized to minimize pile up. Trials were conducted for three base supporting materials: PTFE, PMMA, and aluminum. Results show that PMMA performed better than the other materials. Positive deflection was minimized when the PMMA thickness was at least fifteen times that of the copper sheet. Physical experiments were completed with a thin copper sheet to verify the results. An array of micro-indentations was also created in a bulk steel sample. In order to assess the effect of dimpling via micro-forming, nano-indentation was performed near and far from the deformed material of the dimples. Similar to the laser textured sample, no significant differences were found between the two locations.

Effectiveness of multi-shape laser surface texturing in the reduction of friction under lubrication regime

2016 ◽  
Vol 68 (1) ◽  
pp. 116-124 ◽  
Author(s):  
Dawit Zenebe Segu ◽  
Pyung Hwang
Keyword(s):  
Hydrodynamic Lubrication ◽  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing ◽  
Textured Surface ◽  
Content Type ◽  
Laser Ablation Process ◽  
Specific Formula ◽  
Steel Surfaces ◽  
Lubrication Conditions

Purpose – The purpose of this paper is to investigate and discuss the effect of multi-shape laser surface texturing (LST) steel surfaces on tribological performance. Design/methodology/approach – The textured surface with some specific formula arrays was fabricated by laser ablation process by combining patterns of circles and triangles, circles and squares and circles and ellipses. The tribological test was performed by a flat-on-flat tribometer under dry and lubrication conditions, and results were compared with that of untextured surface. Findings – The results showed that the textured surface had better friction coefficient performance than the untextured surface due to hydrodynamic lubrication effect. Through an increase in sliding speed, the beneficial effect of LST performance was achieved under dry and lubrication conditions. Originality/value – This paper develops multi-shape LST steel surfaces for improving the friction and wear performance under dry and lubrication conditions.

Laser surface texturing inhibits Bioflim formation

2021 ◽  
pp. 124909
Author(s):  
Venkata Sai Prabhu Suraj Nanduru ◽  
Nagalla Siva Ramakrishna ◽  
Ramineni Surendra Babu ◽  
P. Dinesh Babu ◽  
P. Marimuthu ◽  
...  
Keyword(s):  
Surface Texturing ◽  
Laser Surface ◽  
Laser Surface Texturing
Sign in / Sign up

Export Citation Format

Share Document