scholarly journals Minimum miscibility pressure computation in eor by flare gas flooding

2018 ◽  
Vol 10 (2) ◽  
pp. 61
Author(s):  
Tjokorde Walmiki Samadhi ◽  
Utjok W.R. Siagian ◽  
Angga P Budiono
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Gas Injection ◽  
Molar Ratio ◽  
Co2 Injection ◽  
Co2 Flooding ◽  
Minimum Miscibility Pressure ◽  
Gas Flooding ◽  
Model Oil ◽  
Gas Drive

The technical feasibility of using flare gas in the miscible gas flooding enhanced oil recovery (MGF-EOR) is evaluated by comparing the minimum miscibility pressure (MMP) obtained using flare gas to the MMP obtained in the conventional CO2 flooding. The MMP is estimated by the multiple mixing cell calculation method with the Peng-Robinson equation of state using a binary nC5H12-nC16H34 mixture at a 43%:57% molar ratio as a model oil. At a temperature of 323.15 K, the MMP in CO2 injection is estimated at 9.78 MPa. The MMP obtained when a flare gas consisting of CH4 and C2H6 at a molar ratio of 91%:9% is used as the injection gas is predicted to be 3.66 times higher than the CO2 injection case. The complete gas-oil miscibility in CO2 injection occurs via the vaporizing gas drive mechanism, while flare gas injection shifts the miscibility development mechanism to the combined vaporizing / condensing gas drive. Impact of variations in the composition of the flare gas on MMP needs to be further explored to confirm the feasibility of flare gas injection in MGF-EOR processes. Keywords: flare gas, MMP, miscible gas flooding, EORAbstrakKonsep penggunaan flare gas untuk proses enhanced oil recovery dengan injeksi gas terlarut (miscible gas flooding enhanced oil recovery atau MGF-EOR) digagaskan untuk mengurangi emisi gas rumah kaca dari fasilitas produksi migas, dengan sekaligus meningkatkan produksi minyak. Kelayakan teknis injeksi flare gas dievaluasi dengan memperbandingkan tekanan pelarutan minimum (minimum miscibility pressure atau MMP) untuk injeksi flare gas dengan MMP pada proses MGF-EOR konvensional menggunakan injeksi CO2. MMP diperkirakan melalui komputasi dengan metode sel pencampur majemuk dengan persamaan keadaan Peng-Robinson, pada campuran biner nC5H12-nC16H34 dengan nisbah molar 43%:57% sebagai model minyak. Pada temperatur 323.15 K, estimasi MMP yang diperoleh dengan injeksi CO2 adalah 9.78 MPa. Nilai MMP yang diperkirakan pada injeksi flare gas yang berupa campuran CH4-C2H6 pada nisbah molar 91%:9% sangat tinggi, yakni sebesar 3.66 kali nilai yang diperoleh pada kasus injeksi CO2. Pelarutan sempurna gas-minyak dalam injeksi CO2 terbentuk melalui mekanisme dorongan gas menguap (vaporizing gas drive), sementara pelarutan pada injeksi flare gas terbentuk melaui mekanisme kombinasi dorongan gas menguap dan mengembun (vaporizing/condensing gas drive). Pengaruh variasi komposisi flare gas terhadap MMP perlu dikaji lebih lanjut untuk menjajaki kelayakan injeksi flare gas dalam proses MGF-EOR.Kata kunci: flare gas, MMP, miscible gas flooding, EOR

Novel CO2/N2 Foam Concept and Optimization Scheme for Improving CO2-foam EOR Process

2021 ◽  
Author(s):  
Rahul Gajbhiye
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Gas Injection ◽  
Supercritical Conditions ◽  
Co2 Gas ◽  
Reservoir Condition ◽  
Injection Process ◽  
Co2 Foam ◽  
Gas Flooding ◽  
Foam Flooding

Abstract Nitrogen and Carbon dioxide are the most common gases utilized in enhanced oil recovery (EOR) techniques. Most of the gas injection process suffers from the gravity override and viscous fingering resulting in lower oil recovery. Foam is introduced in enhanced oil recovery (EOR) to mitigate these problems encountered during gas flooding. When it comes to the CO2-gas injection the CO2-becomes supercritical at a typical reservoir condition giving it difficulty to form CO2-foam at reservoir condition. The CO2-foam has a common problem to become weaker above its supercritical conditions of 1100 psi and 31°C. As a result, the advantages of using CO2 foam are diminished due to the weakness of CO2-foam at supercritical conditions and results in a lower recovery. However, CO2-foam can be generated by replacing a portion of CO2 with N2 gas. It lacks the understating of mixture properties and its effect on EOR. This study evaluates the performance of CO2/N2 foam at supercritical conditions for EOR. It aims to improve recovery under supercritical conditions by using N2/CO2 mixture foam and optimize the foam quality and CO2/N2 ratio. The results from the experiments showed that the CO2/N2 foam flooding recovered an additional oil of Original Initial Oil in Place (OIIP) indicating that foam flooding succeeded in producing more oil than pure CO2-foam injection processes. Also, the results of foam flooding at different foam quality and CO2/N2 ratio significantly affected the performance and recovery of the process. Hence it is necessary to optimize the CO2/N2 foam parameters flooding process which is affected by the parameters such as foam quality and CO2/N2 ratio. The study also shows an experimental approach for optimizing CO2/N2 foam parameters. The concept of adding N2 to CO2 is a novel way of generating CO2 foam at supercritical conditions. Although investigators are trying different ways to generate the strong and stable CO2- foam, adding N2 to CO2 can be considered to be the easiest way for foam generation as CO2 is always having some impurities in the form of other gases and N2 can be considered as one of such gas helps in generating the foam.

scholarly journals Study of the impact of injection parameters on the performance of miscible sour gas injection for enhanced oil recovery

2019 ◽  
Vol 10 (4) ◽  
pp. 1575-1589
Author(s):  
Aminu Yau Kaita ◽  
Oghenerume Ogolo ◽  
Xingru Wu ◽  
Isah Mohammed ◽  
Emmanuel Akaninyene Akpan
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Gas Injection ◽  
Research Work ◽  
Gas Concentration ◽  
Acid Gas ◽  
Minimum Miscibility Pressure ◽  
Injection Parameters ◽  
The Impact ◽  
Sour Gas

AbstractSour gas reservoirs have faced critics for environmental concerns and hazards, necessitating a novel outlook to how the produced sour gases could be either utilized or carefully disposed. Over the years of research and practice, several methods of sour gas processing and utilization have been developed, from the solid storage of sulfur to reinjecting the sour gas into producing or depleted light oil reservoir for miscible flooding enhanced oil recovery. This paper seeks to investigate the impact of injection parameters on the performance of sour gas injection for enhance oil recovery. In designing a miscible gas flooding project, empirical correlations are used and the key parameter which impacts the phase behavior is identified to be the minimum miscibility pressure (MMP). A compositional simulator was utilized in this research work to study the effect of injection parameters such as minimum miscibility pressure, acid gas concentration, injection pressure and injection rate on the performance of miscible sour gas injection for enhanced oil recovery. The findings showed that methane concentration had a significant impact on the MMP of the process. Additionally, an increase in acid gas concentration decreases the MMP of the process as a result of an increase in gas viscosity, consequently extending the plateau period resulting in late gas breakthrough and increased overall recovery of the process.

scholarly journals A New Predictive Method for CO2-Oil Minimum Miscibility Pressure

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Dangke Ge ◽  
Haiying Cheng ◽  
Mingjun Cai ◽  
Yang Zhang ◽  
Peng Dong
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Accurate Determination ◽  
Contact Process ◽  
Gas Injection ◽  
New Model ◽  
Cell Method ◽  
Minimum Miscibility Pressure ◽  
Miscible Gas Injection ◽  
Tie Lines

Gas injection processes are among the effective methods for enhanced oil recovery. Miscible and/or near miscible gas injection processes are among the most widely used enhanced oil recovery techniques. The successful design and implementation of a miscible gas injection project are dependent upon the accurate determination of minimum miscibility pressure (MMP), the pressure above which the displacement process becomes multiple-contact miscible. This paper presents a method to get the characteristic curve of multiple-contact. The curve can illustrate the character in the miscible and/or near miscible gas injection processes. Based on the curve, we suggest a new model to make an accurate prediction for CO2-oil MMP. Unlike the method of characteristic (MOC) theory and the mixing-cell method, which have to find the key tie lines, our method removes the need to locate the key tie lines that in many cases is hard to find a unique set. Moreover, unlike the traditional correlation, our method considers the influence of multiple-contact. The new model combines the multiple-contact process with the main factors (reservoir temperature, oil composition) affecting CO2-oil MMP. This makes it is more practical than the MOC and mixing-cell method, and more accurate than traditional correlation. The method proposed in this paper is used to predict CO2-oil MMP of 5 samples of crude oil in China. The samples come from different oil fields, and the injected gas is pure CO2. The prediction results show that, compared with the slim-tube experiment method, the prediction error of this method for CO2-oil MMP is within 2%.

scholarly journals A review of chemical-assisted minimum miscibility pressure reduction in CO2 injection for enhanced oil recovery

Petroleum ◽  
2021 ◽  
Author(s):  
Mohamed Almobarak ◽  
Zangyuan Wu ◽  
Daiyu Zhou ◽  
Kun Fan ◽  
Yongbing Liu ◽  
...  
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Co2 Injection ◽  
Pressure Reduction ◽  
Minimum Miscibility Pressure

scholarly journals The Effect of Carbonyl and Hydroxyl Compounds on Swelling Factor, Interfacial Tension, and Viscosity in CO2 Injection: A Case Study on Aromatic Oils

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 94
Author(s):  
Asep Kurnia Permadi ◽  
Egi Adrian Pratama ◽  
Andri Luthfi Lukman Hakim ◽  
Doddy Abdassah
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Viscosity Reduction ◽  
Co2 Injection ◽  
Minimum Miscibility Pressure ◽  
Lower Viscosity ◽  
Hydroxyl Compounds ◽  
Swelling Factor

A factor influencing the effectiveness of CO2 injection is miscibility. Besides the miscible injection, CO2 may also contribute to oil recovery improvement by immiscible injection through modifying several properties such as oil swelling, viscosity reduction, and the lowering of interfacial tension (IFT). Moreover, CO2 immiscible injection performance is also expected to be improved by adding some solvent. However, there are a lack of studies identifying the roles of solvent in assisting CO2 injection through observing those properties simultaneously. This paper explains the effects of CO2–carbonyl and CO2–hydroxyl compounds mixture injection on those properties, and also the minimum miscibility pressure (MMP) experimentally by using VIPS (refers to viscosity, interfacial tension, pressure–volume, and swelling) apparatus, which has a capability of measuring those properties simultaneously within a closed system. Higher swelling factor, lower viscosity, IFT and MMP are observed from a CO2–propanone/acetone mixture injection. The role of propanone and ethanol is more significant in Sample A1, which has higher molecular weight (MW) of C7+ and lower composition of C1–C4, than that in the other Sample A9. The solvents accelerate the ways in which CO2 dissolves and extracts oil, especially the extraction of the heavier component left in the swelling cell.

Applicability of Enhanced Oil Recovery techniques on mature fields - Interest of gas injection

2005 ◽  
Author(s):  
Frederic Maubeuge ◽  
Danielle Christine Morel ◽  
Jean-Pierre Charles Fossey ◽  
Said Hunedi ◽  
Jacques Albert Danquigny
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Gas Injection ◽  
Recovery Techniques

scholarly journals Investigation of Oil Recovery in Fractured Carbonate Rock by

2016 ◽  
Vol 6 (1) ◽  
pp. 14
Author(s):  
H. Karimaie ◽  
O. Torsæter
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Co2 Injection ◽  
Recovery Method ◽  
Asmari Limestone ◽  
Fractured Carbonate ◽  
Efficient Recovery ◽  
Live Oil ◽  
Non Equilibrium

The purpose of the three experiments described in this paper is to investigate the efficiency of secondary andtertiary gas injection in fractured carbonate reservoirs, focusing on the effect of equilibrium gas,re-pressurization and non-equilibrium gas. A weakly water-wet sample from Asmari limestone which is the mainoil producing formation in Iran, was placed vertically in a specially designed core holder surrounded withfracture. The unique feature of the apparatus used in the experiment, is the capability of initializing the samplewith live oil to obtain a homogeneous saturation and create the fracture around it by using a special alloy whichis easily meltable. After initializing the sample, the alloy can be drained from the bottom of the modified coreholder and create the fracture which is filled with live oil and surrounded the sample. Pressure and temperaturewere selected in the experiments to give proper interfacial tensions which have been measured experimentally.Series of secondary and tertiary gas injection were carried out using equilibrium and non-equilibrium gas.Experiments have been performed at different pressures and effect of reduction of interfacial tension werechecked by re-pressurization process. The experiments showed little oil recovery due to water injection whilesignificant amount of oil has been produced due to equilibrium gas injection and re-pressurization. Results alsoreveal that CO2 injection is a very efficient recovery method while injection of C1 can also improve the oilrecovery.

Sign in / Sign up

Export Citation Format

Share Document