scholarly journals Investigation of Oil Recovery in Fractured Carbonate Rock by

2016 ◽  
Vol 6 (1) ◽  
pp. 14
Author(s):  
H. Karimaie ◽  
O. Torsæter
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Co2 Injection ◽  
Recovery Method ◽  
Asmari Limestone ◽  
Fractured Carbonate ◽  
Efficient Recovery ◽  
Live Oil ◽  
Non Equilibrium

The purpose of the three experiments described in this paper is to investigate the efficiency of secondary andtertiary gas injection in fractured carbonate reservoirs, focusing on the effect of equilibrium gas,re-pressurization and non-equilibrium gas. A weakly water-wet sample from Asmari limestone which is the mainoil producing formation in Iran, was placed vertically in a specially designed core holder surrounded withfracture. The unique feature of the apparatus used in the experiment, is the capability of initializing the samplewith live oil to obtain a homogeneous saturation and create the fracture around it by using a special alloy whichis easily meltable. After initializing the sample, the alloy can be drained from the bottom of the modified coreholder and create the fracture which is filled with live oil and surrounded the sample. Pressure and temperaturewere selected in the experiments to give proper interfacial tensions which have been measured experimentally.Series of secondary and tertiary gas injection were carried out using equilibrium and non-equilibrium gas.Experiments have been performed at different pressures and effect of reduction of interfacial tension werechecked by re-pressurization process. The experiments showed little oil recovery due to water injection whilesignificant amount of oil has been produced due to equilibrium gas injection and re-pressurization. Results alsoreveal that CO2 injection is a very efficient recovery method while injection of C1 can also improve the oilrecovery.

Study on CO2 Injection for Enhancing the Oil Recovery at Gao89 Block in Shengli Oilfield

2013 ◽  
Vol 734-737 ◽  
pp. 1464-1467
Author(s):  
Song Lin Shi ◽  
Jian Kang ◽  
Meng Li
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Low Permeability ◽  
Recovery Method ◽  
Shengli Oilfield ◽  
Geological Features ◽  
Efficient Recovery ◽  
Original Production ◽  
Enhance Oil Recovery

Gao 89 Block is a low permeability oil reservoir. These reservoirs have difficulty in water injection, poor well condition, and low original production. Gas injection can solve this problem. It is the most efficient recovery method for low-permeability reservoirs at home and abroad. In accordance with the geological features and development actuality of Gao89 Block, the feasibility and optimization of gas injection are studied, the effect of gas injection on the development index and development results are demonstrated. The results indicate that the gas injection can dramatically enhance oil recovery and increase the oil production.

Experimental Investigation of Near-Miscible Water-Alternating-Gas Injection Performance in Water-Wet and Mixed-Wet Systems

SPE Journal ◽  
2013 ◽  
Vol 18 (01) ◽  
pp. 114-123 ◽  
Author(s):  
S. Mobeen Fatemi ◽  
Mehran Sohrabi
Keyword(s):  
Relative Permeability ◽  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Laboratory Data ◽  
Co2 Injection ◽  
Water Alternating Gas ◽  
Three Phase ◽  
The Impact ◽  
Wag Injection

Summary Laboratory data on water-alternating-gas (WAG) injection for non-water-wet systems are very limited, especially for near-miscible (very low IFT) gas/oil systems, which represent injection scenarios involving high-pressure hydrocarbon gas or CO2 injection. Simulation of these processes requires three-phase relative permeability (kr) data. Most of the existing three-phase relative permeability correlations have been developed for water-wet conditions. However, a majority of oil reservoirs are believed to be mixed-wet and, hence, prediction of the performance of WAG injection in these reservoirs is associated with significant uncertainties. Reliable simulation of WAG injection, therefore, requires improved relative permeability and hysteresis models validated by reliable measured data. In this paper, we report the results of a comprehensive series of coreflood experiments carried out in a core under natural water-wet conditions. These included water injection, gas injection, and also WAG injection. Then, to investigate the impact of wettability on the performance of these injection strategies, the wettability of the same core was changed to mixed-wet (by aging the core in an appropriate crude oil) and a similar set of experiments were performed in the mixed-wet core. WAG experiments under both wettability conditions started with water injection (I) followed by gas injection (D), and this cyclic injection of water and gas was repeated (IDIDID). The results show that in both the water-wet and mixed-wet cores, WAG injection performs better than water injection or gas injection alone. Changing the rock wettability from water-wet to mixed-wet significantly improves the performance of water injection. Under both wettability conditions (water-wet and mixed-wet), the breakthrough (BT) of the gas during gas injection happens sooner than the BT of water in water injection. Ultimate oil recovery by gas injection is considerably higher than that obtained by water injection in the water-wet system, while in the mixed-wet system, gas injection recovers considerably less oil.

scholarly journals Numerical Simulation of Two-Phase Flows in Heterogeneous Porous Media

2020 ◽  
Vol 21 (2) ◽  
pp. 339
Author(s):  
I. Carneiro ◽  
M. Borges ◽  
S. Malta
Keyword(s):  
Porous Media ◽  
Oil Recovery ◽  
Flow Behavior ◽  
Water Injection ◽  
Heterogeneous Porous Media ◽  
Flow In Porous Media ◽  
High Porosity ◽  
Two Phase ◽  
Recovery Method ◽  
Porosity And Permeability

In this work,we present three-dimensional numerical simulations of water-oil flow in porous media in order to analyze the influence of the heterogeneities in the porosity and permeability fields and, mainly, their relationships upon the phenomenon known in the literature as viscous fingering. For this, typical scenarios of heterogeneous reservoirs submitted to water injection (secondary recovery method) are considered. The results show that the porosity heterogeneities have a markable influence in the flow behavior when the permeability is closely related with porosity, for example, by the Kozeny-Carman (KC) relation.This kind of positive relation leads to a larger oil recovery, as the areas of high permeability(higher flow velocities) are associated with areas of high porosity (higher volume of pores), causing a delay in the breakthrough time. On the other hand, when both fields (porosity and permeability) are heterogeneous but independent of each other the influence of the porosity heterogeneities is smaller and may be negligible.

Risk Assessment and Enhanced Oil Recovery Effect of Gravity Assisted Oxygen-Reduced Air Flooding

2021 ◽  
Author(s):  
Lijuan Huang ◽  
Zongfa Li ◽  
Shaoran Ren ◽  
Yanming Liu
Keyword(s):  
Natural Gas ◽  
Oil Recovery ◽  
Gas Injection ◽  
Oil Production ◽  
Air Injection ◽  
Oil Reservoirs ◽  
Displacement Efficiency ◽  
Risk Area ◽  
Recovery Method ◽  
High Risk Area

Abstract The technology of air injection has been widely used in the second and tertiary recovery in oilfields. However, due to the injected air and natural gas will explode, the safety of the gas injection technology has attracted much attention. Gravity assisted oxygen-reduced air flooding is a new method that eliminates explosion risks and improves oil recovery in large-dip oil reservoirs or thick oil layers. The explosion limit data of different components of natural gas under high pressure were obtained through explosion experiments, which verified the suppression effect of oxygen-reduced air on explosions. The influence of natural gas composition and concentration on explosion limits was also investigated. In addition, a rotatable displacement device was used to study the feasibility of gravity assisted oxygen-reduced air injection for improving the heavy oil reservoirs recovery. Under pressure and temperature conditions of 20MPa and 371K, the sand-filled gravity flooding experiments with different dip angles were carried out using oxygen-reduced air with an oxygen content of 8%. The results show that with the increase of the reservoir dip, the pore volume of the injected fluid at the gas channeling point, the efficient development time of gas injection, and the final displacement efficiency of gas injection development all increase through gravity stabilization caused by gravity differentiation. In the presence of a dip angle, the cumulative oil production before the gas breakthrough point exceeded 80% of the oil production during the entire production process, indicating that gravity assisted oxygen-reduced air flooding is an effective and safe improving oil recovery method. Finally, the explosion risk of each link of the air injection process is analyzed, and the high-risk area and the low-risk area are determined.

scholarly journals Investigation of Properties Alternation during Super-Critical CO2 Injection in Shale

2019 ◽  
Vol 9 (8) ◽  
pp. 1686 ◽  
Author(s):  
Sai Wang ◽  
Kouqi Liu ◽  
Juan Han ◽  
Kegang Ling ◽  
Hongsheng Wang ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Supercritical Co2 ◽  
Indentation Test ◽  
Nitrogen Adsorption ◽  
Xrd Analysis ◽  
Bet Surface Area ◽  
Co2 Injection ◽  
Co2 Flooding ◽  
Recovery Method ◽  
Injection Process

The low recovery of oil from tight liquid-rich formations is still a major challenge for a tight reservoir. Thus, supercritical CO2 flooding was proposed as an immense potential recovery method for production improvement. While up to date, there have been few studies to account for the formation properties’ variation during the CO2 Enhanced Oil Recovery (EOR) process, especially investigation at the micro-scale. This work conducted a series of measurements to evaluate the rock mechanical change, mineral alteration and the pore structure properties’ variation through the supercritical CO2 (Sc-CO2) injection process. Corresponding to the time variation (0 days, 10 days, 20 days, 30 days and 40 days), the rock mechanical properties were analyzed properly through the nano-indentation test, and the mineralogical alterations were quantified through X-ray diffraction (XRD). In addition, pore structures of the samples were measured through the low-temperature N2 adsorption tests. The results showed that, after Sc-CO2 injection, Young’s modulus of the samples decreases. The nitrogen adsorption results demonstrated that, after the CO2 injection, the mesopore volume of the sample would change as well as the specific Brunauer–Emmett–Teller (BET) surface area which could be aroused from the chemical reactions between the CO2 and some authigenic minerals. XRD analysis results also indicated that mesopore were altered due to the chemical reaction between the injected Sc-CO2 and the minerals.

scholarly journals Minimum miscibility pressure computation in eor by flare gas flooding

2018 ◽  
Vol 10 (2) ◽  
pp. 61
Author(s):  
Tjokorde Walmiki Samadhi ◽  
Utjok W.R. Siagian ◽  
Angga P Budiono
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Gas Injection ◽  
Molar Ratio ◽  
Co2 Injection ◽  
Co2 Flooding ◽  
Minimum Miscibility Pressure ◽  
Gas Flooding ◽  
Model Oil ◽  
Gas Drive

The technical feasibility of using flare gas in the miscible gas flooding enhanced oil recovery (MGF-EOR) is evaluated by comparing the minimum miscibility pressure (MMP) obtained using flare gas to the MMP obtained in the conventional CO2 flooding. The MMP is estimated by the multiple mixing cell calculation method with the Peng-Robinson equation of state using a binary nC5H12-nC16H34 mixture at a 43%:57% molar ratio as a model oil. At a temperature of 323.15 K, the MMP in CO2 injection is estimated at 9.78 MPa. The MMP obtained when a flare gas consisting of CH4 and C2H6 at a molar ratio of 91%:9% is used as the injection gas is predicted to be 3.66 times higher than the CO2 injection case. The complete gas-oil miscibility in CO2 injection occurs via the vaporizing gas drive mechanism, while flare gas injection shifts the miscibility development mechanism to the combined vaporizing / condensing gas drive. Impact of variations in the composition of the flare gas on MMP needs to be further explored to confirm the feasibility of flare gas injection in MGF-EOR processes. Keywords: flare gas, MMP, miscible gas flooding, EORAbstrakKonsep penggunaan flare gas untuk proses enhanced oil recovery dengan injeksi gas terlarut (miscible gas flooding enhanced oil recovery atau MGF-EOR) digagaskan untuk mengurangi emisi gas rumah kaca dari fasilitas produksi migas, dengan sekaligus meningkatkan produksi minyak. Kelayakan teknis injeksi flare gas dievaluasi dengan memperbandingkan tekanan pelarutan minimum (minimum miscibility pressure atau MMP) untuk injeksi flare gas dengan MMP pada proses MGF-EOR konvensional menggunakan injeksi CO2. MMP diperkirakan melalui komputasi dengan metode sel pencampur majemuk dengan persamaan keadaan Peng-Robinson, pada campuran biner nC5H12-nC16H34 dengan nisbah molar 43%:57% sebagai model minyak. Pada temperatur 323.15 K, estimasi MMP yang diperoleh dengan injeksi CO2 adalah 9.78 MPa. Nilai MMP yang diperkirakan pada injeksi flare gas yang berupa campuran CH4-C2H6 pada nisbah molar 91%:9% sangat tinggi, yakni sebesar 3.66 kali nilai yang diperoleh pada kasus injeksi CO2. Pelarutan sempurna gas-minyak dalam injeksi CO2 terbentuk melalui mekanisme dorongan gas menguap (vaporizing gas drive), sementara pelarutan pada injeksi flare gas terbentuk melaui mekanisme kombinasi dorongan gas menguap dan mengembun (vaporizing/condensing gas drive). Pengaruh variasi komposisi flare gas terhadap MMP perlu dikaji lebih lanjut untuk menjajaki kelayakan injeksi flare gas dalam proses MGF-EOR.Kata kunci: flare gas, MMP, miscible gas flooding, EOR

scholarly journals Experimental Study on Enhanced Oil Recovery by Nitrogen-Water Alternative Injection in Reservoir with Natural Fractures

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiang Li ◽  
Yuan Cheng ◽  
Wulong Tao ◽  
Shalake Sarulicaoketi ◽  
Xuhui Ji ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Water Flooding ◽  
Orthogonal Experimental Design ◽  
Fractured Reservoir ◽  
Natural Fractures ◽  
Nitrogen Injection

The production of a low permeability reservoir decreases rapidly by depletion development, and it needs to supplement formation energy to obtain stable production. Common energy supplement methods include water injection and gas injection. Nitrogen injection is an economic and effective development method for specific reservoir types. In order to study the feasibility and reasonable injection parameters of nitrogen injection development of fractured reservoir, this paper uses long cores to carry out displacement experiment. Firstly, the effects of water injection and nitrogen injection development of a fractured reservoir are compared through experiments to demonstrate the feasibility of nitrogen injection development of the fractured reservoir. Secondly, the effects of gas-water alternate displacement after water drive and gas-water alternate displacement after gas drive are compared through experiments to study the situation of water injection or gas injection development. Finally, the reasonable parameters of nitrogen gas-water alternate injection are optimized by orthogonal experimental design. Results show that nitrogen injection can effectively enhance oil production of the reservoir with natural fractures in early periods, but gas channeling easily occurs in continuous nitrogen flooding. After water flooding, gas-water alternate flooding can effectively reduce the injection pressure and improve the reservoir recovery, but the time of gas-water alternate injection cannot be too late. It is revealed that the factors influencing the nitrogen-water alternative effect are sorted from large to small as follows: cycle injected volume, nitrogen and water slug ratio, and injection rate. The optimal cycle injected volume is around 1 PV, the nitrogen and water slug ratio is between 1 and 2, and the injection rate is between 0.1 and 0.2 mL/min.

A Laboratory Study of Coinjection of Water and CO2 to Improve Oil Recovery and CO2 Storage: Effect of Fraction of CO2 Injected

SPE Journal ◽  
2020 ◽  
pp. 1-9
Author(s):  
Emmanuel Ajoma ◽  
Thanarat Sungkachart ◽  
Saria ◽  
Hang Yin ◽  
Furqan Le-Hussain
Keyword(s):  
Oil Recovery ◽  
Laboratory Experiments ◽  
Water Pressure ◽  
Co2 Storage ◽  
Water Injection ◽  
Molar Fraction ◽  
Co2 Injection ◽  
The Core ◽  
Carbon Dioxide Co2 ◽  
Water Saturated

Summary To determine the effect on oil recovery and carbon dioxide (CO2) storage, laboratory experiments are run with various fractions of CO2 injected (FCI): pure CO2 injection (FCI = 1), water-saturated CO2 (wsCO2) injection (FCI = 0.993), simultaneous water and gas (SWAG) (CO2) injection (FCI = 0.75), carbonated water injection (CWI) (FCI = 0.007), and water injection (FCI = 0). All experiments are performed on Bentheimer sandstone cores at 70°C and 11.7 MPa (1,700 psia). The oil phase is composed of 65% hexane and 35% decane by molar fraction. Before any fluid is injected, the core is filled with oil and irreducible water. Pressure difference across the core and production rate of gas are measured during the experiment. The collected produced fluids are analyzed in a gas chromatograph to determine their composition. Cumulative oil recovery after injection is found to be 78 to 83% for wsCO2, 78% for SWAG, 74% for pure CO2, 53% for CWI, and 35% for water. Net CO2 stored is also found to be the highest for wsCO2 (59 to 65% of the pore volume), followed by that for CO2 injection (56%) and that for SWAG (42%). These results suggest that wsCO2 injection might outperform pure CO2 injection at both oil recovery and net CO2stored.

scholarly journals Simulation Study of Allied In-Situ Injection and Production for Enhancing Shale Oil Recovery and CO2 Emission Control

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3961
Author(s):  
Haiyang Yu ◽  
Songchao Qi ◽  
Zhewei Chen ◽  
Shiqing Cheng ◽  
Qichao Xie ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Co2 Emission ◽  
Gas Injection ◽  
Water Injection ◽  
Oil Production ◽  
Injection Rate ◽  
Oil Reservoirs ◽  
Shale Oil ◽  
Shale Oil Reservoirs

The global greenhouse effect makes carbon dioxide (CO2) emission reduction an important task for the world, however, CO2 can be used as injected fluid to develop shale oil reservoirs. Conventional water injection and gas injection methods cannot achieve desired development results for shale oil reservoirs. Poor injection capacity exists in water injection development, while the time of gas breakthrough is early and gas channeling is serious for gas injection development. These problems will lead to insufficient formation energy supplement, rapid energy depletion, and low ultimate recovery. Gas injection huff and puff (huff-n-puff), as another improved method, is applied to develop shale oil reservoirs. However, the shortcomings of huff-n-puff are the low sweep efficiency and poor performance for the late development of oilfields. Therefore, this paper adopts firstly the method of Allied In-Situ Injection and Production (AIIP) combined with CO2 huff-n-puff to develop shale oil reservoirs. Based on the data of Shengli Oilfield, a dual-porosity and dual-permeability model in reservoir-scale is established. Compared with traditional CO2 huff-n-puff and depletion method, the cumulative oil production of AIIP combined with CO2 huff-n-puff increases by 13,077 and 17,450 m3 respectively, indicating that this method has a good application prospect. Sensitivity analyses are further conducted, including injection volume, injection rate, soaking time, fracture half-length, and fracture spacing. The results indicate that injection volume, not injection rate, is the important factor affecting the performance. With the increment of fracture half-length and the decrement of fracture spacing, the cumulative oil production of the single well increases, but the incremental rate slows down gradually. With the increment of soaking time, cumulative oil production increases first and then decreases. These parameters have a relatively suitable value, which makes the performance better. This new method can not only enhance shale oil recovery, but also can be used for CO2 emission control.

Sign in / Sign up

Export Citation Format

Share Document