adsorbed film
Recently Published Documents


TOTAL DOCUMENTS

159
(FIVE YEARS 0)

H-INDEX

22
(FIVE YEARS 0)

2020 ◽  
Vol 849 ◽  
pp. 156230
Author(s):  
Yuanmi Zhang ◽  
Yaxu Wu ◽  
Yumiao Jiang ◽  
Li Wang ◽  
Jinglai Zhang


Langmuir ◽  
2020 ◽  
Vol 36 (48) ◽  
pp. 14811-14818
Author(s):  
Hiromu Sakamoto ◽  
Akihiro Masunaga ◽  
Takanori Takiue ◽  
Hajime Tanida ◽  
Tomoya Uruga ◽  
...  




2018 ◽  
Vol 20 ◽  
pp. 357-363 ◽  
Author(s):  
Matthew Prosniewski ◽  
Andrew Gillespie ◽  
Ernest Knight ◽  
Tyler Rash ◽  
David Stalla ◽  
...  


2017 ◽  
Vol 69 (6) ◽  
pp. 881-890 ◽  
Author(s):  
Bingjing Lin ◽  
A. Kiet Tieu ◽  
Hongtao Zhu ◽  
Buyung Kosasih ◽  
Oyong Novareza

Purpose This paper aims to assess the adsorption behaviour and the adhesion strength of lubricant films formed by polypropylene oxide-polyethylene oxide-polypropylene oxide (PPO-PEO-PPO) with phosphate ester additive on Ti-coated surface and to identify the influence of molecular architecture and phosphate ester additive. Design/methodology/approach The thickness of the adsorbed PPO-PEO-PPO with phosphate ester lubricant films on Ti surfaces was measured by ellipsometry. The adhesion strength of the copolymer and the copolymer with phosphate ester lubricants was studied by the micro-scratch tests; the scratch tracks on the surfaces were observed by atomic force microscopy and scanning electronic microscopy. Findings The copolymer with a higher weight percentage of PPO not only formed a thicker film but also showed stronger adhesion and better lubrication performance. The added phosphate ester increased the film thickness and improved the tribological behaviour. The finding reveals that the adsorbed film thickness which depends on the PPO chain length and the presence of phosphate ester has a considerable effect on the scratch behaviour. Originality/value This paper fulfils the studies about adsorption behaviour and lubrication mechanism of this new lubricant which has not been adequately investigated on the metal surface.



2017 ◽  
Author(s):  
◽  
Andrew Karl Gillespie

The environmental impacts and costs of fossil fuels necessitate the development of clean, renewable fuel sources for vehicular applications. Hydrogen based systems, with water as their byproduct, have zero carbon emissions, which mitigates the negative effects of using conventional fossil fuels. Further, hydrogen can be produced from renewable energy sources, such as renewable electrolysis and biohydrogen. When produced from such methods, hydrogen is a renewable fuel. The main drawback of hydrogen as a fuel is its low energy density at ambient pressures and temperatures. Hydrogen has a mass energy density three times that of gasoline, but occupies more than 30 times the volume. Therefore, it is necessary to increase the volumetric energy density of hydrogen before it can be considered as a practical option. Conventional storage methods for hydrogen include compression and liquefaction. In order to yield a sufficient deliverable storage capacity, these methods require high pressures or cryogenic temperatures. Compressed gas systems require tanks with massive walls which reduce spatial and mass efficiency and thus, vehicle performance. These systems are geometrically constrained due to their high pressure, making them difficult to integrate into the vehicle. Due to these constraints, conventional storage methods are insufficient at increasing the energy density of hydrogen to compete with that of fossil fuels. To bridge this gap, it is necessary to develop a low-pressure, high-capacity storage technology in order to address the temperature, pressure, weight, and volume constraints present in the conventional storage methods. To achieve this, we investigate the storage capacity of nanoporous solids, which are capable of densifying a high volume of hydrogen on their surfaces through the process of adsorption. Several factors affect the adsorptive capacity of these materials, such as specific surface area, pore geometry, and the strength of the adsorption potential. The strength of the adsorption potential often cited as a figure of merit for the adsorptive capacity of new materials and is commonly estimated through the Clausius-Clapeyron relation between two adsorption isotherms. However, this method requires an assumption of the adsorbed film volume, which poses as the primary source of error. From supercritical hydrogen isotherms from 77 - 473 Kelvin, we propose a method to measure the volumes, densities, and thicknesses of the adsorbed film. This method will lead to more accurate isosteric heat calculations, which is an important factor to consider when designing storage tanks. Furthermore, we investigated the correlation between the isosteric heat of adsorption, surface chemistry, and pore size distribution with an adsorbed film. In most of the samples the saturated film density was approximately 100 g/L across a large range of temperatures. The specific volumes of the adsorbed film scaled with specific surface area and binding energies. The saturated, adsorbed film density approaches 100 g/L for all adsorbent types at 77 K. The saturated, adsorbed film thickness was between 3.1 - 3.2 [superscript A] for hydrogen on most sorbent materials. In the future, we intend to investigate changes in these parameters of the adsorbed film with increasing temperature as well as the affects that these changes may have on the estimated values of isosteric heat. Improved estimates of isosteric heats of adsorption will assist in optimizing the thermal properties of on-board storage tanks.



2016 ◽  
Vol 28 (5) ◽  
pp. 299-315 ◽  
Author(s):  
B. Kosasih ◽  
O. Novareza ◽  
H. Zhu ◽  
R. Taheri ◽  
B. Lin ◽  
...  




Sign in / Sign up

Export Citation Format

Share Document