Feasibility Study on Electrical Properties of 20 kV Polymeric Insulator Dry Test and Rainwater Test

Insulator is a very important equipment in an electric power system. Ceramic insulators have been widely used to support conductors in 20 kV power lines. The problem of ceramic insulators is that they are heavy, easily contaminated on the surface and require a lot of energy in the manufacturing process. Therefore, polymer insulators were developed. This paper presents the design of an epoxy resin polymer insulator with Titanium Dioxide (TiO2) as a nanofiller. The leakage current test was carried out in a high voltage laboratory by applying an AC high voltage of 50 Hz to the insulator dry conditions and the insulator wetted by rainwater contaminants. The results of the leakage current test in dry conditions are 487.6 μA, rainwater contaminated conditions are 594.93 μA, insulation resistance in dry conditions is 2.07 G-Ohms, and contaminated conditions are 1.41 G-Ohms. Based on the test results show that the insulator leakage current increases up to 22% when the surface of the insulator is contaminated with rainwater. Meanwhile, the insulation resistance decreased by up to 32% in conditions contaminated with rainwater. The value of leakage current and insulation resistance indicates that the epoxy resin insulator with TiO2 as filler is electrically feasible to use.

Analysis of Leakage Current and Insulator Resistivity for Quality Assurance of Medium Voltage Network Polymer Insulators Alumina - SiO2 in Tropical Climate Simulator Room

The tropical climate of Indonesia, which has moderately high rainfall, has an impact on the output of outdoor insulators. The presence of chemical particles, pollen, and salt in the air will bind to the insulating material's outer surface and settle, resulting in crystallization that allows the insulating material's surface roughness to increase. One of the insulators that are being produced is an insulator made of epoxy resin. The injection of fillers is used to further improve the durability of the outdoor epoxy resin insulators installed in tropical climatic conditions. Epoxy resin from bisphenol A-epichlorohydrin and polyaminoamide combined with silane, alumina, and SiO2 is used as research materials. The parameters examined were leakage current and resistance to insulation. The use of silane as a hardener will also improve the resistivity on the surface of the insulator, which makes it more difficult to flow or reduces the leakage current. Alumina is well-known for being a solid heat and voltage insulator. The addition of SiO2 to the epoxy resin insulating material increases the insulator's mechanical strength in the form of tensile and compressive strength. With fluctuations in temperature and humidity, the artificial tropical environment is replicated in a test chamber. The value of the leakage current increases with an increase in temperature and humidity. The correlation between air temperature and humidity and insulation resistance is inversely proportional, the higher the temperature applied to the insulator, the lower the insulator resistivity. The same refers to the relationship between air humidity and resistance to insulation. The higher the humidity applied to the insulator, the lower the insulator resistivity. At a test voltage of 11 kV, a humidity of 60%, and a temperature variation of 25oC, the leakage current of epoxy resin insulators is up to 9.2 uA lower than in a factory-made SiR insulator. The leakage current and insulator resistivity's number is already in the good and protected range such that the insulator can be used and reproduce.

Monitoring System of High Voltage Dielectric Equipment

Based on the research of the main causes of dielectric elements premature aging and electrical destruction of primary dielectric elements in high voltage electrical equipment the complex method for remote monitoring of said electrical equipment has been developed. The developed mobile diagnostic device is allowing detection and periodic control of the most dangerous defects. The set of diagnostic parameters of defects was experimentally obtained by using three physical methods (electromagnetic, optical, and acoustic), and allows to inspect the origin and development of defects, and to determine residual life of dielectric elements with a sufficient degree of reliability. The researched characteristics of the kinetics of reduction in operating parameters of polymer insulators permitted the development of the detection of accelerated increase in defects under the influence of ultra-large partial discharges.

About structural elements of polymer insulators of the contact network

The high load on electrified lines makes tougher the requirements for the reliability and maintainability of power supply devices. Insulators are a critical element of the overhead contact network, and great attention is paid to improving their characteristics — electrical and mechanical strength. Advantages of polymer insulators in comparison with traditional ones made of porcelain and glass are generally recognized: manufacturability, low weight, compactness, ease of installation and transportation, high mechanical strength and shock resistance.The article presents the results of comprehensive studies of the electrophysical characteristics of fiberglass rods and bars made of AG-4S carried out by the University of Railway Engineers (MIIT), which were used in the developed polymer structures of the contact network. Recommendations are given on the maintenance of fiberglass rods and bars from AG-4S and their engineering support. The issues of the mechanical strength of polymer insulators of the overhead contact network are covered quite fully, therefore, this article offers the basic principles for calculating their electrical strength. The main requirements for modern polymer insulators and design features are briefly presented for each type: suspended, tension, cantilever, fixing and supporting.

Leakage current signal parameter of various surface roughness conditions of field-aged polymer insulators

This paper presents the signal parameter of leakage current based on various surface roughness degradation conditions for field-aged high voltage polymer insulators. The arithmetical mean of surface roughness is measured accordingly, and also the surface leakage current signal is captured effectively using data acquisition device via the electrical stress test. With the variation of field-aged insulators ages which include 6-year, 12-year and 18-year, they have been mechanically tested using a surface roughness tester along with electrical testing by using the standard method of inclined plane test. The surface roughness data are recorded meanwhile the leakage current signals are further analyzed using Spectrogram to extract the signal parameter. These include the instantaneous root mean squared current, the instantaneous total harmonic distortion, the instantaneous total non- harmonic distortion and the instantaneous total waveform distortion. From the results of the comparative study, it has shown that the statistical quantity of leakage current signal parameters is responding in an increasing trend with respect to the incremental of the surface roughness. Thus, the signal parameters of the leakage current are able to indicate the degradation conditions of insulator surface.